Canon Mk1500 Manuel utilisateur

PUB. 4Y5-8222-010 ©Nisca Corporation 2011 PRINTED IN JAPAN

User’s Guide

Please read this guide before operating this product.

After you finish reading this guide, store it in a safe place for future reference.

User's Guide

Regulations for this product FCC Regulations

This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Do not make any changes or modifications to the equipment unless otherwise specified in the manual.

If such changes or modifications should be made, you could be required to stop operation of the equipment.

Trademarks

• "Canon" and the Canon logo are the registered trademarks or the trademarks of Canon Inc.

Notices

• The contents of this document may not be duplicated in whole or in part by any means without

permission.

• The information in this document is subject to change without notice.

• In no event shall Nisca Corporation bear any responsibility for any direct or indirect damages arising

from the use of our product.

• In no event shall Nisca Corporation bear any responsibility for any direct or indirect damages resulting

from the improper use of our product by the customer, or from modifications or changes made to our

product by the customer.

• If you find any errors or omissions in this document, or if you have any questions concerning this

document, contact your nearest dealer.

• The data created/saved with this printer cannot be backed up in another storage device such as the

hard disk of the PC. We assume no responsibility for the loss caused by data disappearance due to a

machine failure, repair, inspection, or weak battery as well as the carry-over loss.

A Vital Tool for Electrical Facilities

Introducing the Mk1500

When you open a power distribution panel, you are confronted with an array of tightly packed terminals, circuit

breakers, and switches, and these myriad devices are connected by a maze of cables. If each device and cable

is not clearly labeled with a symbol or a number, maintenance can become a nightmare. In such electrical

facilities, it is common practice to use printed tube to identify cables and printed labels to identify switches.

The Mk1500 is used to print such labels and tube.

Easy yet high-quality

printing

Printing tube

The Mk1500 can print

tube that identify cables:

“AB-01” or “+20V”, for

example. Because the tube

that is used is available

commercially, the Mk1500

provides an economical

solution. The Mk1500 can

also be used to print on heat

shrink tube and 4mm I.D.

strip.

Label switches clearly

Printing labels

The Mk1500 can also be

used to print label tape (sold

separately). Because labels

that correspond to speciﬁc

cable tube labels can be

printed and applied to the

corresponding devices,

using such labels results in

improved efﬁciency.

Label with clear adhesive

lamination

Wrap-around tape

with printable and

laminating layers

When applied after printing,

the printing is covered by

plastic laminating ﬁlm,

protecting the characters

from scratching.

Adheres to cables after they

have been connected.

Tube

Labeled with switch

name or number

Clear

laminate seal

Main Features

1Compact and easy to carry

In addition to being compact at 250 mm (W) x 300 mm (D) x 85 mm (H), the printer also has a

lightweight design (2kg), making it easy to transport to the site of electrical facilities. Overall, the

printer greatly increases work efﬁciency.

2Supports a variety of printing media

The printer can print on commercially available tube, label tape, heat shrink tube, wrap around tape, and

4mm I.D. strip.

3Legible printing even in cool environments

Install the optional Tube Warmer to print legibly in environments as cool as 5°C.

4Many functions not normally found in a hand-portable machine

Includes a variety of standard features such as adjustable character size, spacing and margins, and ﬁle

saving capabilities that are hard to imagine in such a light-weight machine.

Contents

Explanation of Symbols.......................................4

Safety Precautions...............................................5

Quick Guide to Using the Printer .......................12

Part 1 Before You Begin (Preparation)

1.1 Names and Functions of Parts .......... 18

Main Unit ....................................................18

LCD screen ................................................20

Keyboard ....................................................21

1.2 Connecting the AC Adapter................ 23

Part 2 Basic Operations

2.1 Printing on Tube and Clear Tube........ 26

Install cassettes ......................26

Insert tube ..............................28

Turn the power switch on........29

Input characters......................30

Print ........................................33

2.2 Printing on Label Tape, Heat Shrink

Tube, and 4mm I.D. Strip .................34

Install cassettes ......................34

Turn the power switch on........37

Input characters......................38

Print ........................................41

2.3 Printing on Wrap-around Tape ........... 42

Installing the cassettes ...........42

Installing the wrap-around tape

guide.......................................43

Turn the power switch on........44

Input characters......................45

Print ........................................47

Part 3 Character Input

3.1 Inputting Characters ........................... 50

Inputting characters ....................................50

3.2 Inputting Symbols............................... 51

Inputting symbols........................................51

3.3 Deleting Characters, Creating New

Pages, Moving the Cursor............... 52

Deleting or changing characters.................52

Deleting all entered text data......................53

Creating a new page ..................................53

Inserting a page .........................................54

Deleting a page ..........................................54

Moving the cursor.......................................55

Part 4 Advanced Operations

4.1 Changing the Characters and the

Number of Lines .............................. 58

Changing character size.............................58

Changing the spacing between characters 59

Adding an underline to “6” and “9” ..............60

Adding a frame to characters......................61

Printing on two lines ...................................62

4.2 Saving, Retrieving and Deleting

Character Data ................................. 64

Files............................................................64

Saving character data.................................65

Loading character data...............................66

Deleting character data ..............................67

4.3 Various Printing Functions ................68

Printing count .............................................68

Changing the printing orientation ...............70

Changing the length and the character

alignment ................................................72

Printing a specific page multiple times

(Continuous Print) ................................... 74

Generating sequential characters (serial

printing) ................................................76

Adjusting the printing start position and

vertical position.......................................79

Adjusting the printing density .....................81

4.4 Changing the Cutting Method............ 82

Half cuts and full cuts .................................82

Turning off half cuts ....................................82

4.5 Other Operations ................................ 84

Removing the print media ..........................84

Changing the display contrast ....................86

Restoring the initial settings........................87

Increasing the printing speed .....................88

Contents

Part 5 Maintenance

5.1 If a Tube or Label Tape Becomes

Jammed ............................................ 90

Action to Take against Media Jam

(When the “Media JAM” message is

displayed)................................................90

Actions to Take against Other Jams

(When the “Media JAM” message is not

displayed)................................................92

When a Tube or Label Tape is Not

Ejected/Fed.............................................94

5.2 What To Do If the Cutter

Is Getting Blunt................................ 96

Changing the cutting depth ........................96

5.3 Replacing the Cutter........................... 98

5.4 Replacing the Cassette..................... 100

Replacing the ribbon cassette ..................100

Replacing a tube or the label tape

cassette................................................. 101

5.5 Maintenance ...................................... 102

Cleaning the printer..................................102

Cleaning the transport rollers ...................102

Cleaning the print head ............................104

Cleaning/Replacing the tube cleaner .......104

Part 6 Appendices

6.1 Consumable Supplies and

Options........................................... 106

Consumable supplies ...............................106

Options.....................................................107

6.2 Message List ..................................... 108

6.3 Troubleshooting................................ 109

6.4 List of Symbols ..................................111

6.5 List of Function ................................. 112

6.6 Main Specifications .......................... 113

Explanation of Symbols

The meanings of the symbols that are used in this manual are explained below.

WARNING A precaution to be followed to use the printer in safe is written. Failure to follow it can

result in fatal or serious injury. Be sure to follow it.

CAUTION A precaution to be followed to use the printer in safe is written. Failure to follow it can

result in an injury. Be sure to follow it.

CAUTION A precaution to be followed to use the printer properly is written. Failure to follow it can

break the printer or damage other products. Be sure to follow it.

An important notice or restriction to be followed to prevent troubles due to improper

operation is written. Be sure to read it.

Supplementary information is provided to facilitate operation.

Supplementary information about the operational procedure is written.

Indicates a page that should be referenced in regards to a speciﬁc operation. Refer to the

information on that page.

Indicates a key that should be pressed on the keyboard.

Safety Precautions

In order to ensure safe operation of the printer, be certain to observe the following safety precautions.

The shape of the power plug varies according to country.

WARNING

Do not disassemble or modify the unit

Disassembling or modifying the unit could cause a ﬁre or damage the

unit.

Do not handle the power cord with wet hands

Do not attempt to plug in or unplug the AC adapter plug, etc., while

your hands are wet. Doing so could result in electric shock.

Do not place the unit in the vicinity of heating devices

Do not place the unit or the AC adapter cord in the vicinity of heating

devices. Doing so could cause the unit or the cord to melt, which could

result in ﬁre or electric shock.

Keep away from paint thinner, etc.

Do not place the unit near alcohol, paint thinner, or other ﬂammable

solvents. The solvents could come into contact with internal electric

components and cause a ﬁre or electric shock.

Plug the power cord in securely

Be sure to plug the AC adapter plug into the power outlet securely.

Failing to do so could result in a ﬁre or electric shock.

Always keep the AC plug clean

Clean the AC adapter plug periodically. If dust, dirt, soot, etc., is

allowed to accumulate on the plug, the dust could absorb moisture,

creating an insulation fault that could cause a ﬁre.

Do not continue to use the unit if an abnormality develops

If the unit begins to smoke or emit an unusual odor, turn the power

switch off immediately, unplug the AC adapter plug from the power

outlet, and then contact your nearest dealer. Continuing to use the unit

after an abnormal condition has developed could result in ﬁre or electric

shock.

Do not connect to a multi-outlet adapter or extension cord

Do not connect this unit to a multi-outlet adapter or extension cord.

Doing so could result in ﬁre or electric shock.

Do not power on with the power cord tied. It can cause ﬁre or electrical

shock.

Do not use sprays, etc., in the vicinity of the unit

Do not use ﬂammable sprays in the vicinity of this unit. The spray

could come into contact with internal components of the unit, resulting

in a ﬁre or electric shock.

Do not clean with paint thinner, etc.

If it is necessary to wipe dirt off the unit, use gauze that has been

dampened with water and then thoroughly wrung out. Never use

ﬂammable solvents such as alcohol, benzene or paint thinner. The

solvents could come into contact with internal electric components and

cause a ﬁre or electric shock.

Turn the unit off for cleaning

Before cleaning the unit, turn the power off and unplug the AC adapter

from the power outlet. Injury could result if the power switch is

inadvertently left in the “ON” position and the unit is put into operation.

Table des matières

Autres manuels Canon Imprimante

Canon

Canon Printer Manuel utilisateur

Canon

Canon Pixma IP4950 Manuel utilisateur

Canon

Canon pixma mx927 series Manuel utilisateur

Canon

Canon FAXPHONE L100 Manuel utilisateur

Canon

Canon iP5000 - PIXMA Color Inkjet Printer Mode d’emploi

Canon

Canon IR C2100 Manuel de programmation

Canon

Canon PIXMA PRO-10 Manuel utilisateur

Canon

Canon NP7160 Manuel utilisateur

Canon

Canon pro-10s series Guide de configuration

Canon

Canon MultiPASS L6000 Manuel utilisateur

Canon

Canon NP6260 Manuel utilisateur

Canon

Canon Laser Shot LBP-2900 Manuel utilisateur

Canon

Canon IMAGECLASS MF249dw Manuel utilisateur

Canon

Canon Selphy CP600 Manuel utilisateur

Canon

Canon PIXMA TS8152 Manuel utilisateur

Canon

Canon PIXMA G1411 Guide de configuration

Canon

Canon imagePROGRAFi iPF840 series Guide de l'utilisateur

Canon

Canon MAXIFY MB5020 Mode d’emploi

Canon

Canon Color imageRUNNER LBP5970 Manuel utilisateur

Canon

Canon i-SENSYS LBP122dw Manuel utilisateur

Canon

Canon Pixma TS3400 Series Manuel utilisateur

Canon

Canon Pixma E480 series Manuel d'instructions

Canon

Canon Color imageCLASS LBP712Cdn Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur

Epson

Epson Stylus Photo PX700W Instructions de montage

Ricoh

Ricoh SP204SF Manuel utilisateur

Star Micronics

Star Micronics futurePRNT TSP100 Manuel utilisateur

Epson

Epson TM-TM88V-i Manuel d'utilisation et d'entretien