Canon I860 Series Manuel utilisateur

REFILLING CANON PRINTERS

i860 and similar.

In the past I’ve owned several Epson, H.P, and one

Lexmark printer. With this Canon i860 I think I’ve found the

first consumer friendly printer, and that’s saying a lot.!!!!

This printer has an ink cartridge that can be removed

entirely for cleaning in about two seconds after the ink

tanks have been taken out, and it only take a couple of

seconds to remove all five of those. The cartridge case

can be easily cleaned by soaking in Windex or a mild

ammonia solution. How good can this get!!!!

As far as filling the ink tank with bulk ink, I’ve found there’s

a lot of confusion out there. I’ve found a way to fill these

tanks without leaking and with an easy technique, so this

is to share that with you.

TO BEGIN

Tools:You’ll need the following tools to do this job. Just

about everyone has these except maybe the glue gun.

Drill motor and a very small drill a bit larger than the

diameter of the fill needle.

Hot glue gun and glue (of course)

Bulk ink refilling kit (from Atlascopy.com--of course)

Ink (Same as above)

Newspapers (in case you make a mess first time)

And that’s about it!

THE INK TANKS

These aren’t cartridges, they’re tanks, which means there

is no sophisticated controllers built in, they’re only simple

tanks to hold ink. The ink comes out the bottom past a felt

lined round hole and into the cartridge (which does have

all those important controllers) and then to the paper.

The tanks have two internal spaces, one is filled with foam

and the other empty. There’s a transit space between the

two spaces for the ink to move from the empty space (a

reservoir) to the foam filled space. The computer uses

infra red technology to read the tanks and can report the

amount of ink remaining to you using the software “setup

utility). Another nice feature is the fact that the tanks are

clear plastic, so you can find out how low the ink is just by

taking out the tanks and looking at them.

Important: Don’t confuse the two black tanks! The large

tank “BK3e” is pigmented ink. It’s used primarily for text.

The smaller black tank “BK6” is dye based and is used for

photo. Don’t put pigmented ink into the small tank--it won’t

work! You may wind up buying a new cartridge!!!

HERE WE GO!!!

First, have the syringe laying down in front of you already

filled with the ink of choice, your rubber gloves on, paper

down on the table, and a sink nearby. You’ll need to

carefully clean the syringe after each fill in order to prevent

cross contamination. Have the drill handy to pick up with

the drill inserted. Have the glue gun hot and ready to go.

METHOD

You’ll need to drill two holes, one in each of these spaces,

on the top of each. Drill the first above the foam filled area

and slightly down into the foam to be sure there’s a clear

passage for venting. This prevents something called

“vapor locking” which won’t allow any ink to leave from the

bottom.

NEXT,

With your rubber gloves on, put your finger over the exit

hole on the bottom below the foam filled space. Hold it

tight! Now drill another hole on the top of the empty

reservoir near the front. You’ll see a slight dimpled spot

almost to the front. Drill there. Now you’re ready to insert

the ink. Pick up the syringe and fill the space almost to the

top. If there’s any ink at all on the top near the hole, wipe it

off with a paper towel, pick up the glue gun and spread a

bit of hot glue over and slightly around the hole. This is the

“fill hole”---not the vent hole over the foam area.

Continue to hold your finger over the exit till the glue sets

up and you’re done. How easy was that????

Once you’re set up it shouldn’t take more than fifteen or

twenty minutes to fill all the tanks even including cleanup.

It’ll go quicker after the first time as the holes are already

drilled. In future fills it’ll be necessary to clear the hole

each time over the reservoir in order for the needle to

enter. Generally that will mean using the drill again as the

glue will go down into the hole a bit.

If you don’t get a good seal with the glue over the fill hole,

ink will immediately begin to run out of the exit hole on the

bottom. I tried using electrical tape as others have

suggested, and even though it was applied very tightly, it

didn’t seal. The glue does, and is easy to use. Only

problem with it is the need to clear the fill hole each time

you want to refill. The tape would have been more

convenient, but that’s the way it goes!!!

Caveat:

I haven’t tried this with any other Canon printer so can’t

vouch for this method with any other than the i860. Seems

that it ought to work on any with this tank system though,

but you’ll have to try for yourselves.

Good printing :-)

Ted Johnson

Autres manuels pour i860 Series

Table des matières

Autres manuels Canon Imprimante

Canon

Canon iR1018 Manuel utilisateur

Canon

Canon MP-C635 Manuel utilisateur

Canon

Canon LBP-1760 Manuel utilisateur

Canon

Canon FC220 Manuel utilisateur

Canon

Canon imagePRESS V1000 Manuel technique

Canon

Canon imageCLASS LBP-6650DN Manuel utilisateur

Canon

Canon Color imageCLASS MF8280Cw Manuel de service

Canon

Canon ImagePROGRAF iPF680 Manuel utilisateur

Canon

Canon MK5000 Instructions de montage

Canon

Canon PiXMA TR8550 Series Manuel utilisateur

Canon

Canon PIXMA MX512 Manuel utilisateur

Canon

Canon LBP-2000 Manuel utilisateur

Canon

Canon S520 Manuel utilisateur

Canon

Canon LBP361dw Manuel utilisateur

Canon

Canon i-SENSYS LBP6680x Manuel utilisateur

Canon

Canon PIXMA PRO-100 Series Manuel utilisateur

Canon

Canon imagePROGRAF iPF820 Manuel utilisateur

Canon

Canon imageCLASS MFG500 Series Guide de configuration

Canon

Canon MF275dw Manuel utilisateur

Canon

Canon Laser Shot LBP-1420 Manuel utilisateur

Canon

Canon GX5070 Guide de configuration

Canon

Canon i 320 Manuel utilisateur

Canon

Canon PIXMA iP2700 Manuel utilisateur

Canon

Canon iR6570 series Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur

Epson

Epson Stylus Photo PX700W Instructions de montage

Ricoh

Ricoh SP204SF Manuel utilisateur

Star Micronics

Star Micronics futurePRNT TSP100 Manuel utilisateur

Epson

Epson TM-TM88V-i Manuel d'utilisation et d'entretien

Canon i860 Series Manuel utilisateur

Manuels Imprimante populaires d'autres marques