Canon BJC-6000 Series Manuel

BJC-6000 Series Setup Instructions

Step 1: Remove All Shipping Tape and Protective Materials

Note that tape may not be in the exact locations shown here.

Remove all tape and material from the front, back, and inside of the printer.

Make sure you have these items:

• BC-31 Color BJ Cartridge

• BC-30 Black BJ Cartridge

• Documentation kit (User's Manual, Warranty Card, Registration Card)

• Canon Creative Pro CD packet

• Printer cable (not included)

Check the outside of your box for other contents.

Important! Save the box and shipping materials. You may need them later if you have to transport the

printer.

Step 2: Select a Location for the Printer

• Choose a flat sturdy surface with enough space around the printer to store and feed paper.

• Avoid placing the printer in direct sunlight.

• Fully extend the paper support and paper output tray to ensure enough space is available for proper

operation.

• Make sure you have enough room to manually feed single sheets of paper from the back of the printer

• Always lift the printer by gripping both sides.

Step 3: Connect The Printer To The Computer

Important! Make sure the printer and your computer are turned off.

1. Connect a parallel cable to the printer.

• You need to purchase a parallel cable from your dealer.

• The cable must be a Centronics-compatible, bi-directional cable (IEEE 1284-compliant).

2. Then connect the cable to your computer's parallel port..

Step 4: Plug In The Printer

1. Plug the printer into a properly grounded AC outlet.

You can plug the power cord from the printer into either a wall outlet or a power surge protector.

Important! Never turn off the printer using a power strip.

2. Turn on the printer.

Press the POWER button to turn on the printer. The printer beeps once and the POWER light starts to flash.

Step 5: Install The BC-31 Color BJ Cartridge

Important! Spilled ink can stain any surface. Open BJ cartridges and Ink Tanks very carefully to

protect against spilled ink.

1. Lower the paper output tray and lift up the front cover.

The cartridge holder moves to the center of the printer.

2. Remove the shipping material and tape from the cartridge holder.

• Remove the protective cover.

• Remove tape from the left and right side of the cartridge holder.

3. Raise the blue lock lever on the right side of the cartridge holder.

The cartridge holder moves to the center of the printer.

4. Remove the BC-31 Color BJ Cartridge from its box.

Remove the orange protective cap from the print head, and then remove the orange tape.

Do not attempt to replace the cap on a BJ cartridge.

5. Insert the BJ cartridge.

• Set the BC-31 Color BJ cartridge into the right slot of the cartridge holder.

• Lower the blue lock lever on the right side of the holder until it locks into place.

• Remove the empty protective tanks one by one from inside the BJ cartridge; press the tab on each tank to

release it.

6. Prepare the Ink Tank.

• Start with the BCI-3Y (Yellow) Ink Tank.

• Pull up the orange tape to break the seal of the clear film.

• Remove the film.

• Push the lever on the protective orange cap in the direction of the arrow and gently twist it off.

• To prevent spilling ink, do not apply force when twisting off the cap. Use firm even pressure and twist

slowly.

7. Insert the Ink Tank.

• Insert the BCI-3Y (Yellow) Ink Tank into the first slot on the right side of the BJ cartridge.

• Gently press down on the top of the Ink Tank until it locks into place.

8. Insert the other Ink Tanks.

• Repeat steps 6 and 7 for the BCI-3M (Magenta) and BCI-3C (Cyan) Ink Tanks.

• Insert the magenta tank into the center slot and the cyan tank into the left slot.

Step 6: Install The BC-30 Black BJ Cartridge

1. Raise the blue lock lever on the left side of the cartridge holder.

2. Remove the BC-30 Black BJ Cartridge from its box.

• Remove the orange protective cap from the print head, and then remove the orange tape.

• Do not attempt to replace the cap on a BJ cartridge.

3. Insert the BJ cartridge.

• Set the BC-30 Black BJ cartridge into the left slot of the cartridge holder.

• Lower the blue lock lever on the left side of the holder until it locks into place.

• Remove the protective tank from inside the BJ cartridge.

4. Prepare the Ink Tank.

• Pull up the orange tape to break the seal of the clear film. Remove the film.

• Push the lever on the protective orange cap in the direction of the arrow and gently twist it off.

• To prevent spilling ink, do not apply force when twisting off the cap. Use firm even pressure and twist

slowly.

5. Insert the Ink Tank.

• Insert the BCI-3BK (Black) Ink Tank into the slot in the BJ cartridge.

• Gently press down on the top of the Ink Tank until it locks into place.

6. Close the front cover.

After you close the front cover, you will hear the cartridge holder return to the home position.

The printer automatically cleans the print heads.

Step 7: Load Paper

1. Pull up the paper support; then lower the paper output tray and pull it all the way out.

Move the paper guide to the left to match the width of your paper.

2. Fan a stack of paper and slide it into the sheet feeder until it stops.

• Adjust the paper guide snug to the edge of the stack.

• The sheet feeder holds up to 130 sheets of paper.

• Make sure the stack of paper does not exceed the limit mark and tab.

Step 8: Install The Printer Driver

Important! You must install the BJC-6000 Series Printer Driver for Windows. The printer driver controls the

communication between the printer and your computer. Installing your printer driver is easy. Use the Canon Creative Pro

CD-ROM and follow these simple bjc6000steps for one of the following operating systems:

Printer Setup for Windows 98/ Windows 95/ NT 4.0

Starting your System

Start your system in this order:

1. Make sure your computer is turned off.

2. Check that the printer is connected to the computer.

3. Make sure the printer is turned on.

4. Now turn on the computer.

Starting Windows Printer Setup

If you see a "New Hardware Found", "Update Device Driver Wizard" or "Add New Hardware Wizard" screen, click Cancel.

(Click whatever you need to until you return to the Windows Desktop.)

3. When you see the Windows Desktop, follow these bjc6000steps:

1. Insert the Canon Creative Pro CD-ROM into your CD-ROM drive.

oIf Setup starts automatically, go to 3.

oIf Setup doesn't start, from the taskbar, click Start and then Run.

1. Type D:\SETUP (where D: is your CD-ROM drive - most CD-ROM drives are D: or E: - try

D: first; if you see an error message, try E:). Then click OK.

2. Follow the on-screen instructions. Be sure to wait for Windows to complete each operation.

Click OK to restart your computer.

Note: The next time you start your computer, you may see the "New Hardware Found" screen. Wait a few

seconds while the system updates itself; the screen will disappear.

Printer Setup for Windows 3.1

Starting your System

Turn on your printer, and then turn on your computer.

Starting Windows 3.1

Be sure to wait for Windows to complete each operation.

1. Insert the CD-ROM labeled Canon Creative Pro into your CD-ROM drive.

2. From Program Manager, select Run in the File menu.

3. Type D:\SETUP (where D: is your CD-ROM drive). Then click OK.

4. Follow the on-screen instructions.(Select BJC-6000 Series from the list of printers.)

5. When complete, restart Windows.

Autres manuels pour BJC-6000 Series

Table des matières

Autres manuels Canon Imprimante

Canon

Canon E4500 Series Guide de configuration

Canon

Canon iP90v - PIXMA Color Inkjet Printer Manuel utilisateur

Canon

Canon PIXMA MP190 Manuel utilisateur

Canon

Canon BJC-85 Manuel utilisateur

Canon

Canon BJC-S520 Manuel

Canon

Canon i 320 Manuel utilisateur

Canon

Canon Pixma iP4300 Series Manuel utilisateur

Canon

Canon 3410 Manuel utilisateur

Canon

Canon PIXMA TS6100 series Manuel utilisateur

Canon

Canon Pixma iP110 series Manuel utilisateur

Canon

Canon imageCLASS LBP-6650DN Manuel utilisateur

Canon

Canon PIXMA MP800 Manuel utilisateur

Canon

Canon PIXMA Pro9000 Mark II Series Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

Canon

Canon iP100 - PIXMA Color Inkjet Printer Manuel utilisateur

Canon

Canon BJC-3000 Series Manuel utilisateur

Canon

Canon iPF650 - imagePROGRAF Color Inkjet Printer Guide de l'utilisateur

Canon

Canon Oce VarioPrint 110 Manuel utilisateur

Canon

Canon iP8500 - PIXMA Color Inkjet Printer Manuel utilisateur

Canon

Canon 2238B002 Manuel utilisateur

Canon

Canon PIXMA iX6520 Manuel utilisateur

Canon

Canon image Prograf iPF680 Series Guide de l'utilisateur

Canon

Canon imageCLASS MF5880dn Guide de sécurité

Canon

Canon 4496B008AA Guide de configuration

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur

Ricoh

Ricoh Aficio AP400 Manuel utilisateur

BIXOLON

BIXOLON SRP-352plusV Manuel utilisateur

Epson

Epson Stylus Photo PX700W Instructions de montage

Ricoh

Ricoh SP204SF Manuel utilisateur

Star Micronics

Star Micronics futurePRNT TSP100 Manuel utilisateur

Epson

Epson TM-TM88V-i Manuel d'utilisation et d'entretien