Canon EF70 Manuel utilisateur
EF70-200mm f/2.8L IS II USM
Instruction
ENG
COPY
ENG-1
Dedicated to EOS cameras, the Canon EF70-
200mm f/2.8L IS II USM lens is a high-
performance telephoto zoom lens equipped
with an Image Stabilizer.
•“IS” stands for Image Stabilizer.
•“USM” stands for Ultrasonic Motor.
Features
1. The Image Stabilizer gives the equivalent
effect of a shutter speed four stops faster*.
2. With fluorite and UD lens elements,
outstanding image delineation is obtained.
3. Ultrasonic motor (USM) for quick and quiet
autofocusing.
4. Manual focusing is available after the subject
comes into focus in autofocus mode (ONE
SHOT AF).
5. A truly round aperture hole results in a nicer
background blur.
6. The lens is compatible with Extender EF1.4X ll
and EF2X ll.
7. Tight seal structure ensures excellent dust-
proof and drip-proof performance.
*Based on [1/focal length] second. Generally, it requires
a shutter speed [1/focal length] second or faster to
prevent camera shake.
Thank you for purchasing a Canon product.
Conventions used in this instruction
Warning to prevent lens or camera malfunction
or damage.
Supplementary notes on using the lens and
taking pictures.
COPY
ENG-2
aSafety Precautions
aSafety Precautions
•Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
•Do not point the lens or camera at the sun or
photograph it. This is because the lens
concentrates the sun’s rays even when the sun is
outside the image area or when shooting with
backlight, which could cause malfunction or fire.
•
Whether it is attached to the camera or not, do not
leave the lens under the sun without the lens cap
attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a fire.
Handling Cautions
•If the lens is taken from a cold environment into
a warm one, condensation may develop on the
lens surface and internal parts. To prevent
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment.Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
•Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules.These limits are designed to provide reasonable protection
against harmful interference in a residential installation.This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Consult the dealer or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
COPY
ENG-3
Nomenclature
Hood mount (→7)
Filter mounting
thread (→13)
Focusing ring (→5)
Focusing distance range selection switch (→5)
Image stabilizer switch (→8)
Image stabilizer mode selector switch (→8)
Focus mode switch (→5)
Distance scale (→11)
Zoom ring (→6)
Contacts (→4)
Tripod mount (→12)
Lens mount index (→4)
Orientation lock knob (→12)
Rubber ring (→4)
For detailed information, reference page numbers are provided in parentheses (→**).
COPY
ENG-4
See your camera’s instructions for details on
mounting and detaching the lens.
•After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
•If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result.The camera and lens
may not operate properly.
•If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
•If you remove the lens, cover it with the dust
cap.To attach it properly, align the lens mount
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise.To remove it,
reverse the order.
1.Mounting and Detaching the Lens
The lens mount has a rubber ring for enhanced
water- and dust-resistance.The rubber ring may
cause slight abrasions around the camera's lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
COPY
ENG-5
You can set the focusing distance range to
1.2 m/3.9 ft. to infinity or 2.5 m/8.2 ft. to infinity.
By setting the suitable focusing distance range,
the actual autofocusing time can be shorter.
3.
Switching the Focusing
Distance Range
2.Setting the Focus
Mode
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
To use only manual focusing (MF), set the focus
mode switch to MF, and focus by turning the
focusing ring.The focusing ring always works,
regardless of the focus mode.
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
COPY
ENG-6
4.Zooming
To zoom, turn the zoom ring.
Be sure to finish zooming before focusing.
Zooming after focusing can affect the focus.
COPY
ENG-7
5.Hood
Attaching
To attach the hood, align the hood’s attachment
position mark with the red dot on the front of the
lens, then turn the hood as shown by the arrow
until the lens' red dot is aligned with the hood's
stop position mark.
The ET-87 hood can keep unwanted light out of the lens, and also protects the front of the lens from
rain, snow, and dust.
Removing
To remove the hood, hold down the button on the
side and turn the hood in the direction of the
arrow until the position mark on the hood aligns
with the red dot.
The hood can be reverse-mounted on the lens
for storage.
•Part of the picture may be blocked if the hood is not attached properly.
•When attaching or detaching the hood, grasp the base of the hood to turn it.To prevent deformation, do not
grasp the rim of the hood to turn it.
Button
COPY
ENG-8
You can use the image stabilizer in AF or MF mode.
6.Image Stabilizer Settings
Select the stabilizer mode.
•MODE 1: Corrects vibrations
in all directions. It is mainly
effective for shooting still
subjects.
•MODE 2: It compensates for
vertical camera shake during
following shots in a horizontal
direction, and compensates for
horizontal camera shake
during following shots in a
vertical direction.
When you press the shutter
button halfway, the Image
Stabilizer will start
operating.
•Make sure the image in the
viewfinder is stable, then press
the shutter button the rest of
the way down to take the
picture.
Set the STABILIZER switch
to .
•If you are not going to use the
image stabilizer function, set
the switch to .
COPY
ENG-9
7.Tips on Using the Image Stabilizer
•In semi-darkened areas such as indoors or
outdoors at night.
•In locations where flash photography is
prohibited, such as art museums and theater
stages.
•In situations where your footing is uncertain.
•In situations where fast shutter settings cannot
be used.
•When panning subjects in motion.
●MODE 1 ●MODE 2
The image stabilizer in this lens is effective for hand-held shots under the following conditions.
COPY
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Canon Lentille
Canon
Canon EF100-400mm f/4.5-5.6L IS II USM Manuel utilisateur
Canon
Canon RF 24-70mm F2.8 L IS USM Manuel utilisateur
Canon
Canon EF 75-300mm f/4-5.6 III USM Manuel utilisateur
Canon
Canon KT20x5B KRSD Manuel utilisateur
Canon
Canon EF28-135mm f/3.5-5.6 IS USM Manuel utilisateur
Canon
Canon RF 135mm F1.8 L IS USM Manuel utilisateur
Canon
Canon CN-E20-50mm T2.4 L F Manuel utilisateur
Canon
Canon 25 mm f:3.5 Manuel utilisateur
Canon
Canon KJ10EX4.5B IRSE Manuel utilisateur
Canon
Canon CN-E70-200mm T4.4 L IS KAS S Manuel utilisateur
Canon
Canon CN7x17 KAS S/E1 Manuel utilisateur
Canon
Canon EF 100mm f/2.8 Macro USM Manuel utilisateur
Canon
Canon A 6000 ILCE-6000 Manuel utilisateur
Canon
Canon RF-24-105mm-f-4L-IS-USM Manuel utilisateur
Canon
Canon HD XS HJ15ex8.5B Manuel utilisateur
Canon
Canon XL 1S Manuel utilisateur
Canon
Canon EF85mm f/1.2L II USM Manuel utilisateur
Canon
Canon EF24-105MM Manuel utilisateur
Canon
Canon RF15-35mm F2.8 L IS USM Manuel utilisateur
Canon
Canon eHDxs HJ11ex4.7B Manuel utilisateur
Manuels Lentille populaires d'autres marques
Tamron
Tamron SP 70-300mm F/4-56 Di VC USD Manuel utilisateur
FujiFilm
FujiFilm FUJINON ZA17x7.6BERD-S6 Manuel utilisateur
Panasonic
Panasonic VW-W4907 Manuel utilisateur
Navitar
Navitar 1-51332 Mode d’emploi
Leica
Leica APO-SUMMICRON-SL 1:2/50 ASPH. Manuel utilisateur
Sony
Sony LKRL-Z200 Series Manuel utilisateur
