Canon EF24-105MM Manuel utilisateur

EF24-105mm F4L IS USM

Instruction

ENG-1

Thank you for purchasing a Canon USM lens.

The Canon EF24-105mm f/4L IS USM lens is a

high-performance standard zoom lens

developed for EOS cameras. It is equipped

with an Image Stabilizer, and covers a wide

range of focal lengths from wide angle to

mid-telephoto. It is equipped with an Image

Stabilizer effective for hand-held shooting at

slow shutter speeds.

¡“IS” stands for Image Stabilizer.

¡“USM” stands for Ultrasonic Motor.

Features

1. Aspheric and super UD lens elements for

excellent imaging performance.

2. The Image Stabilizer gives the equivalent

effect of a shutter speed three stops faster.

3. USM for fast, quiet focusing.

4. Great close-ups at 0.45 m/1.5 ft at all focal

lengths.

5. Manual focusing available in autofocusing

mode (ONE SHOT AF).

6. A truly round aperture hole results in a nicer

background blur.

7. Tight seal structure ensures excellent dust-

proof and drip-proof performance.

Conventions used in this instruction

Warning to prevent lens or camera

malfunction or damage.

Supplementary notes on using the lens

and taking pictures.

ENG-2

aSafety Precautions

1. Do not look at the sun or a bright light source

through the lens or camera. Doing so could result in

loss of vision. Looking at the sun directly through the

lens is especially hazardous.

2. Whether it is attached to the camera or not, do

not leave the lens under the sun without the lens

cap attached. This is to prevent the lens from

concentrating the sun’s rays, which could cause a fire.

aHandling Cautions

If the lens is taken from a cold environment into a warm

one, condensation may develop on the lens surface and

internal parts. To prevent condensation in this case, first

put the lens into an airtight plastic bag before taking it from

a cold to warm environment. Then take out the lens after it

has warmed gradually. Do the same when taking the lens

from a warm environment into a cold one.

his device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Do not make any changes or modifications to the equipment

unless otherwise specified in the instructions. If such changes or

modifications should be made, you could be required to stop

operation of the equipment.

This equipment has been tested and found to comply with the

limits for a class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Consult the dealer or an experienced radio/TV technician for

help.

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus as set out in the

interference-causing equipment standard entitled “Digital

Apparatus”, ICES-003 of the Industry Canada.

N118

ENG-3

Distance scale (→4, 8)

Infrared index (→8)

Contacts (→4)

Focus mode switch (→5)

Image stabilizer switch (→6)

Hood mount (→9)

Lens mount index (→4)

Filter mounting

thread (→10)

Zoom ring (→5)

Focusing ring (→5)

Zoom position index

Nomenclature

For detailed information, reference page numbers are provided in parentheses (→ **).

ENG-4

See your camera’s instructions for details on

mounting and detaching the lens.

¡After detaching the lens, place the lens with the

rear end up to prevent the lens surface and

electrical contacts from getting scratched.

¡If the contacts get soiled, scratched, or have

fingerprints on them, corrosion or faulty

connections can result. The camera and lens

may not operate properly.

¡If the contacts get soiled or have fingerprints on

them, clean them with a soft cloth.

¡If you remove the lens, cover it with the dust

cap. To attach it properly, align the lens mount

index and the

index of the dust cap as shown

in the diagram, and turn clockwise. To remove it,

reverse the order.

Mounting and Detaching the Lens

Close-up Photography (Macro Photography)

The lens mount has a rubber ring for enhanced

water- and dust-resistance. The rubber ring may

cause slight abrasions around the camera's lens

mount, but this will not cause any problems. If the

rubber ring becomes worn, it is replaceable by a

Canon Service Center at cost.

The lens can focus as close as 0.45 m/1.5 ft for

close-ups (macro photography).

To focus at 0.45 m/1.5 ft, set the lens focus mode

switch to MF. Look through the viewfinder and

move your body forward or back to focus. Take the

shot when the subject is in focus.

ENG-5

Setting the Focus Mode

4. Zooming

After autofocusing in ONE SHOT AF mode, focus

manually by pressing the shutter button halfway

and turning the focusing ring. (Full-time manual

focus)

To shoot in autofocus mode, set the focus mode

switch to AF.

To use only manual focusing, set the focus mode

switch to MF, and focus by turning the focusing

ring. The focusing ring always works, regardless

of the focus mode.

To zoom, turn the lens’ zoom ring.

Be sure to finish zooming before focusing.

Changing the zoom ring after focusing can affect

the focus.

ENG-6

5. Image Stabilizer

You can use the image stabilizer in AF or MF mode.

The image stabilizer is particularly

effective for hand-held shots in

the following conditions.

¡Dimly lit scenes, such as at

dusk or indoors

Locations such as art galleries

or theater stages where flash

photography is forbidden

¡Situations in which your

footing is uncertain

1Set the STABILIZER

switch to .

¡If you are not going to

use the image stabilizer

function, set the switch to

2When you press the

shutter button halfway,

the Image Stabilizer

will start operating.

¡Make sure the image in

the viewfinder is stable,

then press the shutter

button the rest of the way

down to take the picture.

ENG-7

Image Stabilizer

¡When you use a tripod, the Image

Stabilizer should be turned off to save

battery power.

¡The stabilizer is equally effective for hand-

held photography and photography with a

monopod.

¡The image stabilizer function also

operates when the lens is used with an

Extension Tube EF12 ll or EF25 ll.

¡If you set the camera’s Custom Function

to change the assigned button to operate

the AF, the Image Stabilizer will operate

when you press the newly assigned AF

button.

¡The Image Stabilizer cannot compensate

for a blurred shot caused by a subject that

moved.

¡Set the STABILIZER switch to when

you are taking pictures using the Bulb

setting (long exposures). If the

STABILIZER switch is set to , the

image stabilizer function may introduce

errors.

¡The Image Stabilizer might not be fully

effective in the following cases:

• You move the camera for a panned shot.

• You shoot while riding on a bumpy road.

¡Compared to using a normal non-IS lens,

fewer shots can be taken when you use

an Image Stabilizer lens because more

power is consumed.

¡The image stabilizer operates for about

two seconds even when your finger is off

the shutter button. Do not remove the lens

while the stabilizer is in operation. This will

cause a malfunction.

¡With the EOS-1V/HS, 3, 30/33/Elan7/7E,

30V/33V/Elan7N/7NE, Elan ll/Elan ll

E/50/50 E, 300/Rebel2000, IX, and D30,

the Image Stabilizer will not work during

self-timer operation.

ENG-8

6. Infinity Distance Mark

To compensate for shifting of the infinity focus

point that results from changes in temperature.

The infinity position at normal temperature is the

point at which the vertical line of the L mark is

aligned with the distance indicator on the

distance scale.

For accurate manual focusing on subjects at

infinity distance, look through the viewfinder while

rotating the focusing ring.

The infrared index corrects the focus setting

when using monochrome infrared film. Focus on

the subject manually, then adjust the distance

setting by moving the focusing ring to the

corresponding infrared index mark.

7. Infrared Index

Some EOS cameras cannot use infrared film. See

the instructions for your EOS camera.

¡The infrared index position is based on a

wavelength of 800 nm.

¡Be sure to observe the manufacturer’s

instructions when using infrared film.

¡Use a red filter also when you take the picture.

ENG-9

The EW-83H hood can keep unwanted light out of the lens, and also protects the lens from rain,

snow, and dust.

To attach the hood, align the hood’s attachment position mark with the red dot on the front of the

lens, then turn the hood clockwise until the lens’s red dot is aligned with the hood’s stop position

mark.

The hood can be reverse-mounted on the lens for storage.

¡Part of the picture may be blocked if the hood is not attached properly.

¡When attaching or detaching the hood, grasp the base of the hood to turn it. To prevent deformation, do not

grasp the rim of the hood to turn it.

8. Hood

Autres manuels pour EF24-105MM

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Canon Objectif de l'appareil photo

Canon

Canon CJ12ex4.3B Manuel utilisateur

Canon

Canon EF-M 22mm f/2 STM Manuel utilisateur

Canon

Canon EF-S60mm f/2.8 MACRO USM Manuel utilisateur

Canon

Canon CN-E14-35mm T1.7 L SP Manuel utilisateur

Canon

Canon EF100-400mm f/4.5-5.6L IS II USM Manuel utilisateur

Canon

Canon EF 35mm 1:2.0 Mode d’emploi

Canon

Canon EF135MM F/2L USM Manuel utilisateur

Canon

Canon RF 28mm F2.8 STM Manuel utilisateur

Canon

Canon EF 24mm f/1.4L II USM Manuel utilisateur

Canon

Canon EF-S18 Manuel utilisateur

Canon

Canon EF-S60mm f/2.8 MACRO USM Manuel utilisateur

Canon

Canon EF 17-40mm f/4L USM Manuel utilisateur

Canon

Canon CN-E30-300mm T2.95-3.7L SP Manuel utilisateur

Canon

Canon EF 28-80mm 1:2.8-4.0L USM Manuel utilisateur

Canon

Canon KT20x5B KRSD Manuel utilisateur

Canon

Canon EF50mm f/1.0L USM Manuel utilisateur

Canon

Canon EF 75-300 mm F4-5 Manuel utilisateur

Canon

Canon EF 70-200mm f/2.8 L IS II USM Manuel utilisateur

Canon

Canon 4318C002 Manuel utilisateur

Canon

Canon TS-E 24mm 1:3.5 L Mode d’emploi

Canon

Canon TS-E17MM F/4L Manuel utilisateur

Canon

Canon IMAGE STABILIZER ULTRASONIC EF300MM f/4L IS... Manuel utilisateur

Canon

Canon EF 180mm f/3.5L MACRO USM Manuel utilisateur

Canon

Canon EF 180mm f/3.5L MACRO USM Mode d’emploi

Manuels Objectif de l'appareil photo populaires d'autres marques

THORLABS

THORLABS ELL15 Manuel utilisateur

FUJICA

FUJICA ZC1000 Manuel utilisateur

Tamron

Tamron A09 Manuel

Sony

Sony SEL-55210 Manuel utilisateur

Sony

Sony VCL-HG2037 Manuel utilisateur

Honeywell

Honeywell HLM25V6F12 Manuel utilisateur

Sony

Sony VCL-ST30 Manuel utilisateur

Sony

Sony SAL-85F14Z - 85mm f1.4 Carl Zeiss Planar T Coated Telephoto... Manuel utilisateur

ARRI

ARRI Lenses Manuel utilisateur

Panasonic

Panasonic LUMIX G X Vario 45-175mm f/4.0-5.6 Manuel utilisateur

Nikon

Nikon AF-S VR 24-120 f/3.5-5.6G IF-ED Manuel utilisateur

Rokinon

Rokinon DS50M-C Manuel utilisateur

Olympus

Olympus M.Zuiko Digital ES 300mm f4.0 IS PRO Manuel utilisateur

Sony

Sony VCL-DE07T Manuel utilisateur

Tamron

Tamron A036 Manuel utilisateur

Samsung

Samsung 20-50mm F3.5-5.6 ED II Manuel utilisateur

Tamron

Tamron 272E Manuel utilisateur

Sinar

Sinar Rolleiflex 6008 AF Manuel utilisateur