Campbell SR05 Manuel utilisateur

Revision:04/2020

Campbell Scientific, Inc.

Table of contents

1. Introduction 1

2. Specifications 1

3. Siting 2

4. Mounting procedure 2

5. Wiring 4

6. Register map 5

7. RS-485 programming 6

8. Analog programming 7

9. Example programs 8

10. Maintenance and troubleshooting 12

Table of Contents - i

1. Introduction

The SR05, manufactured by Hukseflux Thermal Sensors, is an ISO 9060:2018 spectrally flat Class C

(second class) pyranometer designed for general solar radiation measurements in agricultural

and meteorological networks and PV monitoring. Both analog output and Modbus over RS-485

are supported.

2. Specifications

ISO 9060:2018 classification: Spectrally flat Class C (second class)

Digital output: Modbus over 2-wire RS-485

Voltage output: 0 to 1 V

Analog output range: 0 to 1600 W/m²

Default Modbus address: 53

Response time (95 %): 18 s

Calibration uncertainty: < 1.8 % (k = 2)

Zero offset A: < 15 W/m² (unventilated) response to 200 W/m² net thermal

radiation

Zero offset B: < ± 4 W/m² response to 5 K/h change in ambient temperature

Spectral range: 285 to 3000 nm

Operatingtemperaturerange: –40 to 80 °C

Temperature response: < ± 0.4 % (–30 to 50 °C)

Operating voltage range: 5 to 30 VDC

Power consumption: <75 mW at 12 VDC

Weight: 0.35 kg (12.34 oz)

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 1

3. Siting

The solar radiation sensor is usually installed horizontally, but can also be installed at any angle

including an inverted position. Site the sensor to allow easy access for maintenance while ideally

avoiding any obstructions or reflections above the plane of the sensing element. It is important

to mount the sensor such that a shadow or a reflection will not be cast on it at any time. If this is

not possible, try to choose a site where any obstruction over the azimuth range between earliest

sunrise and latest sunset has an elevation not exceeding 5°. Diffuse solar radiation is less

influenced by obstructions near the horizon. The sensor should be mounted with the cable

pointing towards the nearest magnetic pole. For example, in the northern hemisphere, point the

cable toward the North Pole.

4. Mounting procedure

Required tools:

lDiopter

lSolar compass

l8 mm (5/16-inch) open-end wrench for U-bolt nuts

1. On a level surface, level the solar radiation sensor using the leveling feet on the sensor.

Alternatively, remove the sensor leveling feet to allow it to be mounted directly to the

mounting bracket.

2. Secure the solar radiation sensor to the mounting bracket. The blue dots in the following

figure indicate the mounting holes used for this pyranometer.

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 2

3. Using a diopter in combination with a solar compass, install and orient the crossarm on the

tripod or the mast. If installing the mounting bracket on a vertical pole, ensure the pole is

truly vertical.

4. Secure the mounting bracket to the crossarm or vertical pole using the hardware included

with the mounting bracket. The CM255 uses one U-bolt, nuts, flat washers, and lock

washers to mount the bracket, as shown in the following figure.

5. For pyranometers mounted horizontally, ensure the mounting bracket is horizontal in two

dimensions. For pyranometers mounted at an angle, set the mounting bracket angle to the

desired angle prior to tightening the mounting hardware.

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 3

6. Verify mounting hardware is firmly tightened, and that the mounting bracket is at the

desired angle.

5. Wiring

Table 5-1 (p. 4) provides RS-485 wiring and Table 5-2 (p. 5) provides analog wiring.

Table 5-1: RS-485 wire color, function, and data logger connection

Wire color1Function Data logger

connection2

MeteoPV

connection Pin out

Green RS485 A- C(odd) A- 5

White RS485 B+ C(even) B+ 2

Red Power in (12 V) 12V 12V 1

Black Power ground G G 4

Clear Shield ⏚(analog ground) ⏚(analog ground)

1Blue wire is not used.

2Assumes the sensor directly connects to the data logger.

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 4

Table 5-2: Analog wire color, function and data logger connection

Wire color1Function Data logger connection Pin out

Blue Pyranometer signal high

Uconfigured for differential input2,

DIFF H (differential high, analog-voltage

input)

Pyranometer signal

reference

Uconfigured for differential input2, 3,

DIFF L (differential low, analog-voltage

input)3

Red Power in (12 V) 12V 1

Black Ground ⏚(analog ground) 4

Clear Shield ⏚(analog ground)

1Green and white wires are not used.

2Uterminals are automatically configured by the measurement instruction.

3Jumper to ⏚with user-supplied wire.

6. Register map

Table 6-1 (p. 5) provides the register map for the most commonly used values. A comprehensive

Table 6-1: RS-485 register map

Starting register

number

count Data format Units Description

1 1 Signed 16 bit integer Modbus address

3 2 Signed 32 bit integer mW/m² Irradiance (temperature

compensated signal)

7 1 Signed 16 bit integer 0.01 °C Sensor body temperature

8 1 Signed 16 bit integer x 0.1 Ω Sensor electrical

resistance

9 1 Signed 16 bit integer Scaling factor irradiance

10 1 Signed 16 bit integer Scaling factor

temperature

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 5

Table 6-1: RS-485 register map

Starting register

number

count Data format Units Description

11 2 Signed 32 bit integer nV Sensor voltage output

41 1 Signed 16 bit integer Serial number

42 2 Float µV/W/m2Sensor sensitivity

47 2 Signed 32 bit integer Calibration date

7. RS-485 programming

The RS-485 output can be directly read by a MeteoPV, CR6-series, CR1000X-series, or Modbus

RTU RS-485 network. Other Campbell Scientific data loggers can use an MD485 multidrop

interface to read the RS-485 output (refer to the MD485 manual).

A CR6 or CR1000X data logger programmed as a Modbus Master can retrieve the values stored in

the Input Registers. To do this, the CRBasic program requires a SerialOpen() instruction

followed by the ModbusMaster() instruction.

The SerialOpen instruction has the following syntax:

SerialOpen (ComPort, Baud, Format, TXDelay, BufferSize, Mode)

The Format is typically set to logic 1 low; even parity, one stop bit, 8 data bits. The Mode

parameter should configure the ComPort as RS-485 half-duplex, transparent. The

ModbusMaster() instruction has the following syntax:

ModbusMaster (Result, ComPort, Baud, Addr, Function, Variable, Start, Length,

Tries, TimeOut, [ModbusOption])

The Addr parameter must match the sensor Modbus address. To collect all of the values, the

Start parameter needs to be 1 and the Length parameter needs to correspond with the

the CRBasic Editor Help. Refer to Example programs (p. 8) for more information.

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 6

8. Analog programming

The pyranometer outputs a low level voltage that is measured using either the VoltDiff()

CRBasic instruction or VoltSE() CRBasic instruction.

CAUTION:

Nearby AC power lines, electric pumps, or motors can be a source of electrical noise. If the

sensor or data logger is located in an electrically noisy environment, the measurement should

be made with the 60 or 50 Hz rejection integration option as shown in the example programs.

If measurement time is not critical, the autorange option can be used in the VoltDiff() or

VoltSE() instruction; the autorange adds a few milliseconds to the measurement time.

Otherwise, select the input range as follows:

1. Estimate the maximum expected input voltage by multiplying the maximum expected

irradiance (in W × m–2) by the calibration factor (in μV / W × m–2). Divide the answer by

1000 to give the maximum in millivolt units.

2. Select the smallest input range that is greater than the maximum expected input voltage.

If electromagnetic radiation can be a problem, use an fN1 of 50 or 60 Hz. Select 60 Hz Noise

Rejection for North America and areas using 60 Hz AC voltage. Select 50 Hz Noise Rejection for

most of the Eastern Hemisphere and areas that operate at 50 Hz. The multiplier converts the

millivolt reading to engineering units. Table 8-1 (p. 7) provides the calculations required for the

various units. The offset will normally be fixed at zero (see Example programs (p. 8)).

Table 8-1: Multipliers required for flux density and total fluxes

Units Multiplier Output processing

W × m–2 M Average

MJ × m–2 M × t × 0.000001 Totalize

kJ × m–2 M × t × 0.001 Totalize

cal × cm–2 M × t × 0.0239 × 0.001 Totalize

cal × cm–2 × min–1 M × 1.434 × 0.001 Average

W × hr × m–2 M × t / 3600 Totalize

M = 1000/c, where c is the sensor output in μV / W × m–2

t = data logger program execution interval in seconds

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 7

9. Example programs

Table 9-1 (p. 8) provides wiring for the example programs. CRBasic Example 1 (p. 8) uses Modbus

over RS-485 and CRBasic Example 2 (p. 11) uses analog voltage measurements.

Table 9-1: Connections for example programs

Wire color Function RS-485 program

CR1000X connections

Analog program

CR1000X connection

Green RS485A C5 N/C

White RS485B C6 N/C

Red Power in (12 V) 12V 12V

Black Power ground G G

Blue Pyranometer signal high N/C 1H

Pyranometer signal

reference N/C Jumper 1L to ⏚with user-

supplied wire

Clear Shield ⏚(analog ground) ⏚(analog ground)

CRBasic Example 1: CR1000X program using Modbus over RS-485 to measure the SR05

'CR1000X Series Datalogger

'Hukseflux SR2005 Pyranometer

'SR05 is an ISO 9060 Second Class pyranometer

Public CheckSensorID As Boolean

Dim SR05(15) As Long

Public SR05_IRR_TC 'Temperature compensated x 0.01 W/M^2

Public SR05_IRR 'Uncompensated x 0.01 W/M^2

Public SR05_BodyTemp As Float

Public SR05_SerialNumber As Float

Public SR05_CalDate As Long

Public SR05_Humidity As Float

Public SR05_ScaleFactor_IRR As Long

Public SR05_ScaleFactor_BodyTemp As Long

Public SR05_ElecResistance As Long

Public SR05_VoltageOut As Float

SR05 ISO Spectrally Flat Class C (Second Class) Pyranometer with Various Outputs 8

Autres manuels pour SR05

Table des matières

Autres manuels Campbell Instrument de mesure

Campbell

Campbell CM3 Manuel utilisateur

Campbell

Campbell HC2-S3-L Manuel utilisateur

Campbell

Campbell CNR4 Manuel utilisateur

Campbell

Campbell CS300 Manuel utilisateur

Campbell

Campbell CS205 Manuel utilisateur

Campbell

Campbell VWANALYZER Manuel utilisateur

Campbell

Campbell 107 Manuel utilisateur

Campbell

Campbell CS110 Manuel utilisateur

Campbell

Campbell CPEC300 Manuel utilisateur

Campbell

Campbell TCAV Manuel utilisateur

Campbell

Campbell SkyVUE 8 Manuel utilisateur

Campbell

Campbell 105T Manuel utilisateur

Campbell

Campbell CNR4 Manuel utilisateur

Campbell

Campbell MMW-005 Manuel utilisateur

Campbell

Campbell IRGASON Manuel utilisateur

Campbell

Campbell CR23X Manuel utilisateur

Campbell

Campbell HC2S3 Manuel utilisateur

Campbell

Campbell OXYGUARD TYPE III CS512 Manuel utilisateur

Campbell

Campbell TDR100 Manuel utilisateur

Campbell

Campbell LI200R Manuel utilisateur

Campbell

Campbell TEMPERATURE PROBE 109SS Manuel utilisateur

Campbell

Campbell 110PV Manuel utilisateur

Campbell

Campbell HMP60 Manuel utilisateur

Campbell

Campbell CR10TCR Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur