Cameo CLCONTROL6 Manuel utilisateur
6-CHANNEL DMX CONTROLLER
CLCONTROL6
USER´S MANUAL
BEDIENUNGSANLEITUNG
MANUEL D´UTILISATION
MANUAL DE USUARIO
INSTRUKCJA OBSŁUGI
MANUALE D‘USO
Introduction
The Cameo CLCONTROL6 is an especially compact DMX controller with 6 channels that is perfect for controlling
small lighting systems. It can be mounted in many ways and of course can also be used as a freestanding unit; it
is extremely easy to operate.
The CLCONTROL6 has 6 smoothly shifting faders for the individual DMX channels and a master fader. It can
be powered using the included external power adapter or batteries and thus is universally useable for manual
control of DMX systems. A 3-pole XLR socket is used as the DMX output; a red LED serves as a power indicator.
This straightforward lightweight impresses with clear functionality and high user friendliness.
2
3
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESpAñoLpoLSKIITALIANo
Thank you for choosing Cameo Lights!
We have designed this product to give you reliable operation over many years.
Please, take a few moments to read these instructions carefully, as we want you to enjoy your new Cameo Lights
products quickly and to the fullest.
Further information about Cameo Lights check our website WWW.CAMEOLIGHT.COM
6-CHANNEL DMX CONTROLLER
CLCONTROL6
2
3
ITALIANOPOLSKIESPAÑOL
FRANCAISFRANCAIS FRANCAISFRANCAIS FRANCAISDEUTSCHENGLISH
4
5
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESpAñoLpoLSKIITALIANo
PREVENTIVE MEASURES:
1. Please read these instructions carefully.
2. Keep all information and instructions in a safe place.
3. Follow the instructions.
4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.
5. Use the equipment only in the intended manner and for the intended purpose.
6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall
mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.
7. During installation, observ e the applicable safety regulations for your country.
8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make
certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.
9. Never place sources of ignition, e.g., burning candles, on the equipment.
10. Ventilation slits must not be blocked.
11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment -
in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials,
fluids or gases.
12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with
liquids, such as vases or drinking vessels, on the equipment.
13. Make certain that objects cannot fall into the device.
14. Use this equipment only with the accessories recommended and intended by the manufacturer.
15. Do not open or modify this equipment.
16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to
tripping hazards.
17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and
personal injuries.
18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or
if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a
powered device). This equipment may only be repaired by authorized, qualified personnel.
19. Clean the equipment using a dry cloth.
20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate
plastic and paper/cardboard.
21. Plastic bags must be kept out of reach of children.
FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:
22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to
an outlet with a protective ground. Never deactivate the protective ground of a power cord.
23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do
not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the
equipment until it has reached room temperature.
24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match
the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to
the power outlet only if the equipment values and the mains power values match. If the included power cord or
power adapter does not fit in your wall outlet, contact your electrician.
25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the
mains outlet and/or power adapter and the equipment connector.
26. When connecting the equipment, make certain that the power cord or power adapter is always freely
accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want
4
5
ITALIANOPOLSKIESPAÑOL
FRANCAISFRANCAIS FRANCAISFRANCAIS FRANCAISDEUTSCHENGLISH
SAFETY:
to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or
adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.
27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this
can shorten the useful life of the equipment.
28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repea-
tedly, please contact an authorised service centre.
29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter
from the power outlet.
30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be
unlocked before it can be removed. However, this also means that the equipment can slide and fall down if
the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be
careful when laying cables.
31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or
before extended periods of disuse.
CAUTION
RISK OF ELECTRIC S HOCK
DO NOT OPEN
CAUTION:
Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable
parts inside. Have repairs carried out only by qualified service personnel.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user
to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electrical shock.
The exclamation mark within an equilateral triangle is intended to alert the user to the presence of
important operating and maintenance instructions.
CAUTION – HIGH VOLUME LEVELS WITH AUDIO PRODUCTS!
This equipment is intended for professional use. Therefore, commercial use of this equipment is subject to the
respectively applicable national accident prevention rules and regulations. As a manufacturer, Adam Hall is
obligated to notify you formally about the existence of potential health risks.
Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing
high sound-pressure levels (SPL) that can lead to irreversible hearing damage in performers, employees, and
audience members. For this reason, avoid prolonged exposure to volumes in excess of 90 dB.
CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS
1. Do not look into the beam from a distance of less than 40 cm.
2. Do not stare into the beam for extended periods at short-to-medium distances.
3. Do not view the beam directly with optical instruments such as magnifiers.
INTRODUCTION:
FEATURES:
6-CHANNEL DMX CONTROLLER
(CLCONTROL6)
• 6 DMX channels
• 6 smoothly shifting faders
• 1 separate master fader
• light and compact
• operation as a tabletop console
• installable
• ready for wall mounting
• power supply via included power adapter or 9V battery
6
7
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESpAñoLpoLSKIITALIANo
OPERATION:
The CLCONTROL6 is a 6-channel DMX controller with which one or more DMX spotlights in a group with the
same DMX start address (001) can be operated in 6-channel mode with the same DMX signal. If the DMX
spotlights have a 3-channel mode, then two groups of spotlights can be controlled separately (group 1 = DMX
start address 001, group 2 = DMX start address 004); if they have a 2-channel mode, then three groups of
spotlights can be controlled independently (group 1 = DMX start address 001, group 2 = DMX start address 003,
and group 3 = DMX start address 005).
EXAMPLE OF USE:
Controlling 3 x 2 LED lights in 2-channel mode
DMX start address: 001
LED group 1
Controller channel: 1
and 2
DMX out / DMX in
DMX out / DMX in
DMX out / DMX in
DMX out / DMX inDMX out / DMX in
DMX in
DMX start address: 003
LED group 2
Controller channel: 3 and 4
DMX start address: 005
LED group 3
Controller channel: 5 and 6
DMX out
6
7
ITALIANOPOLSKIESPAÑOL
FRANCAISFRANCAIS FRANCAISFRANCAIS FRANCAISDEUTSCHENGLISH
CONTROLS AND DISPLAY:
1CHANNEL FADERS 1 TO 6
When the faders are all the way down, the lowest DMX value (0%) is output; when the faders are all the way
up, the highest DMX value (100%) is output.
2MASTER FADER
Channels 1 to 6 are ganged on this fader, which means that the master fader controls the output of all 6 DMX
channels.
3POWER LED
Lights up when the DMX controller is on, the low-voltage connector of the power adapter is inserted in the
equipment correctly, and the power adapter is connected to the power mains. The LED also lights up during
battery-powered operation.
4MOUNTING HOLES
The 4 mounting holes can be used to fasten the DMX controller securely during installation (installed dimen-
sions W x H x D 148 x 128 x 52 mm).
8
9
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESpAñoLpoLSKIITALIANo
1
2
3
4
REAR PANEL:
1LOW-VOLTAGE SOCKET
Connector for power adapter. Please use only the original power adapter supplied with the equipment.
Note: When the equipment is operated with the power adapter, the battery power supply is automatically
interrupted.
2ON / OFF SWITCH
Always turn the equipment off after use.
3DMX OUTPUT SOCKET
Use a DMX cable to connect the female 3-pole XLR socket of the DMX controller to the DMX input of your
spotlight.
8
9
ITALIANOPOLSKIESPAÑOL
FRANCAISFRANCAIS FRANCAISFRANCAIS FRANCAISDEUTSCHENGLISH
1 2 3
BOTTOM:
1BATTERY COMPARTMENT
For battery-powered operation, a 9V battery must be inserted and connected. Remove the battery before
extended periods of disuse and operation only with the power adapter.
2MOUNTING HOLES FOR WALL MOUNTING
IMPORTANT: The mounting screws must not protrude more than 5 mm into the housing. The spacing bet-
ween holes is 110 mm.
10
11
ENGLISHDEUTSCHFRANCAIS
FRANCAISFRANCAIS FRANCAISFRANCAIS ESpAñoLpoLSKIITALIANo
1
2 2
Table des matières
Langues :
Autres manuels Cameo Routeur réseau
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité