Calculated Industries 4054 Manuel utilisateur

CONSTRUCTION

MASTER

En Español

ADVANCED FEET-INCH-FRACTION CALCULATOR

Model 4054

Pocket Reference Guide

➡

Insert This

Direction



The Construction Master 5 calculator helps

you save time, cut costly errors and build

like a pro!

Quickly Solve:

• Feet-Inches-Fractions, Yards, Metric

Dimensional Problems and Conversions

• Problems Involving All Fractions

— 1/2-1/64ths!

• Areas, Volumes and Weights

• Circle/Arc Calculations

• Common, Hip/Valley, Jack Rafter

Lengths (Regular and Irregular)

• Rake-Wall Solutions

• Concrete, Flooring Quantity

• Roofing Materials

• Squaring-Up

• Stair Layout Solutions, and more!

CONSTRUCTION MASTER®5 v3.1

GETTING STARTED ...............................1

KEY DEFINITIONS/FUNCTIONS..........1

Basic Function Keys ............................1

Dimension Keys...................................2

Arc/Circle Keys ....................................4

Right Triangle/Roof Framing Keys ......4

Stair Layout Key ..................................7

Stair Settings .......................................8

Miscellaneous Functions .....................8

PAPERLESS TAPE EXAMPLE ...........10

PREFERENCE SETTINGS .................11

ENTERING DIMENSIONS ..................13

Linear Dimensions.............................13

Square and Cubic Dimensions..........13

Linear Conversions............................14

Square and Cubic Conversions.........15

BASIC MATH OPERATIONS ..............15

EXAMPLES ...........................................16

Adding and Subtracting Strings of

Dimensions.....................................16

Multiplying Dimensions......................16

Dividing Dimensions ..........................17

Percent Calculations..........................17

Square Area.......................................18

Rectangular Area and Volume...........18

Entering Square and Cubic and

Adding a Waste Allowance.............19

Weight Conversions ..........................19

Weight per Volume ............................20

Using the Memory .............................21

Board Feet and Cost .........................22

Carpentry — Calculating Number

of Studs ..........................................22

Baluster Spacing ...............................23

TABLE OF CONTENTS

Circle Area and Circumference .........24

Arc Angle or Degree ..........................24

Concrete Volume for Driveway..........25

Concrete Columns.............................25

Complex Concrete Volume................26

RIGHT ANGLE/FRAMING...................28

Squaring-Up a Foundation ................29

Pitch — Converting Roof Angle.........29

Converting Slope ...............................30

Common Rafter Length .....................30

Regular Hip/Valley and Jack

Rafters............................................31

Irregular Hip/Valley ............................33

Rake-Wall — No Base.......................34

STAIRS ................................................35

Stairs — Given Rise and Run ...........35

Stairs — Given Only the Floor-to-Floor

Rise; Entering Other Than 7-1/2 Inch

Desired Riser Height ......................37

APPENDIX ............................................38

Setting Fractional Resolution.............38

Default Settings .................................39

Auto-Shut Off.....................................39

Accuracy/Errors .................................40

Battery ...............................................41

Replacing the Battery ........................41

Reset .................................................41

AREA AND VOLUME FORMULAS .....42

REPAIR AND RETURN .......................44

WARRANTY ........................................45

FCC CLASS B .....................................47

LOOKING FOR NEW IDEAS ..............47

POCKET REFERENCE GUIDE — 1

KEY DEFINITIONS / FUNCTIONS

Basic Function Keys

+ – x Arithmetic operation keys.

÷ =

0– 9Keys used for entering

and •numbers.

%Percent Key — Four-func-

tion (+, –, x, ÷) percent key.

OOff Key — Turns all power

off, clearing all non-perma-

nent registers.

oOn/Clear Key — Turns on

power. Pressing once clears

the display. Pressing twice

clears all temporary values.

ÇConvert Key — Used with

the dimensional keys to

convert between dimen-

sions or with other keys to

access special functions.

√Square Root Key — Used to

find the Square Root of a

non-dimensional or area

value.

Ç √ x2Function — Finds the

Square of a linear or non-

dimensional value.

GETTING STARTED

POCKET REFERENCE GUIDE — 2

®Recall Key — Used with

other keys to recall stored

values and settings.

μMemory Key — Adds the

displayed value to Memory.

Clears when the calculator

is shut off.

Ç μ Memory Minus (M–) —

Subtracts the displayed

value from Memory.

Ç ® Memory Clear — Clears

Memory without changing

current display.

® ® Memory Clear — Clears

Memory and displays

Memory Total.

Dimension Keys

yYards Key — Enters or

converts to Yards.

fFeet Key — Enters or con-

verts to Feet as whole or

decimal numbers. Also

used with the iand /

keys for entering Feet-Inch

values (e.g., 6 f 9 i

1 / 2). Repeated press-

es during conversions tog-

gle between Fractional and

Decimal Feet.

POCKET REFERENCE GUIDE — 3

iInch Key — Enters or con-

verts to Inches. Entry can

be whole or decimal num-

bers. Also used with the /

key for entering fractional

inch values (e.g., 9 i 1

/2). Repeated presses

during conversions toggle

between Fractional and

Decimal Inches.

/Fraction Bar Key — Used

to enter Fractions. Fractions

can be entered as proper

(1/2, 1/8, 1/16) or improper

(3/2, 9/8). If the denomina-

tor (bottom) is not entered,

the calculator's fractional

accuracy setting is auto-

matically used.

mMeters Key — Enters or

converts to Meters.

cCentimeters Key — Enters

or converts to Centimeters.

MMillimeters Key — Enters

or converts to Millimeters.

bBoard Feet Key — Enters

or converts Cubic values to

Board Feet. One Board

Foot is equal to 144 Cubic

Inches.

POCKET REFERENCE GUIDE — 4

wWeight Key — Enters or

converts (a volume value)

to Tons, Pounds, Metric

Tons or Kilograms.

Repeated presses will cycle

through these units.

Arc/Circle Keys

CCircle Key — Calculates

Circle Area and

Circumference based on

entered Diameter.

Ç C Arc — Calculates Arc

Length or Degree based on

entered Diameter and Arc

Degree or Length (e.g., if

Arc Degree is entered, it

will calculate Arc Length,

and vice versa).

Right Triangle/Roof Framing Keys

pPitch Key — This key is

used to enter or calculate

the Pitch (Slope) of a roof

(or Right Triangle). Pitch is

the amount of “Rise” over

12 Inches of “Run.” Pitch

may be entered as:

POCKET REFERENCE GUIDE — 5

a Dimension 9 i p

an Angle 3 0 p

a Ratio 0 • 7 5 Ç p

a Percentage 7 5 % p

A Pitch entry will remain in

permanent storage until

revised or reset. A solution

will be replaced by its

entered value once the

calculator is cleared.

Ç p Enters Pitch Ratio (e.g., •

5 8 3 Ç p).

rRise Key — Enters or cal-

culates the Rise or vertical

leg (height) of a Right

Triangle.

RRun Key — Enters or cal-

culates the Run or horizon-

tal leg (base) of a Right

Triangle.

dDiagonal Key — Enters or

calculates the common or

Diagonal leg (Hypotenuse)

of a Right Triangle. Typical

applications are “squaring”

slabs or finding common

rafter lengths.

HHip/Valley Key —

Calculates length of the

Regular or Irregular Hip/

Valley rafter.

POCKET REFERENCE GUIDE — 6

Ç H Irregular Pitch — Enters

Irregular Pitch used to cal-

culate lengths of the

Irregular Hip/Valley and

Jack rafters.

jJack Key — Calculates

Jack rafter lengths on the

Regular-pitched roof side.

Ç j Irregular Jack — Calculates

Jack rafter lengths on the

Irregular-pitched roof side.

∑Rake-Wall Key — Finds

the stud sizes based on

entered Right Triangle val-

ues and the stored On-

Center spacing. If a dimen-

sional value is entered

before pressing ∑, that

value is considered the

base and will be added to

the stud lengths.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Calculated Industries Calculatrice

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Manuel utilisateur

Calculated Industries

Calculated Industries Construction Master III Manuel utilisateur

Calculated Industries

Calculated Industries Home ProjectCalc Manuel utilisateur

Calculated Industries

Calculated Industries 8515 Manuel utilisateur

Calculated Industries

Calculated Industries KitchenCalc 8300 Manuel utilisateur

Calculated Industries

Calculated Industries Sheet Metal/HVAC Pro Calc Manuel utilisateur

Calculated Industries

Calculated Industries Measure Master 4018 Manuel utilisateur

Calculated Industries

Calculated Industries Machinist Calc 4086 Manuel utilisateur

Calculated Industries

Calculated Industries ProjectCalc Plus MX 8528 Manuel utilisateur

Calculated Industries

Calculated Industries KitchenCalc Pro Manuel utilisateur

Calculated Industries

Calculated Industries 4065 Construction Master Pro v3.0 Manuel utilisateur

Calculated Industries

Calculated Industries Material Estimator Manuel utilisateur

Calculated Industries

Calculated Industries 9130 Manuel utilisateur

Calculated Industries

Calculated Industries 4030 Manuel utilisateur

Calculated Industries

Calculated Industries PROJECTCALC CLASSIC 8503 Manuel utilisateur

Calculated Industries

Calculated Industries 4020 Manuel utilisateur

Calculated Industries

Calculated Industries Construction Master IV Manuel utilisateur

Calculated Industries

Calculated Industries CONVERSIONCALC PLUS Manuel utilisateur

Calculated Industries

Calculated Industries 3420 Manuel utilisateur

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8025 Manuel utilisateur

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8020 Manuel utilisateur

Calculated Industries

Calculated Industries Construction Master 5 4050 Manuel utilisateur

Calculated Industries

Calculated Industries TimeCard Tabulator II Manuel utilisateur

Calculated Industries

Calculated Industries 4325 Manuel utilisateur

Manuels Calculatrice populaires d'autres marques

HP 35s Manuel

Casio

Casio CFX-9970G Manuel utilisateur

LEXIBOOK

LEXIBOOK EL350 Manuel utilisateur

HP HP-97 Manuel utilisateur

Citizen

Citizen SDC-414N Manuel utilisateur

Casio

Casio fx-3800P Manuel utilisateur

Canon

Canon P26-DHIII Manuel utilisateur

Citizen

Citizen 520DPA Manuel utilisateur

Sharp

Sharp EL-9900 Manuel utilisateur

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manuel utilisateur

Casio

Casio MS-7UC Manuel utilisateur

Sharp

Sharp WriteView EL-W506 Manuel technique

Casio

Casio FC-200 Manuel utilisateur

Casio

Casio fx-CG50 Manuel utilisateur

HP HP-67 Guide de l'utilisateur

Royal

Royal CBC2000 Manuel utilisateur

Heathkit

Heathkit IC-2009 Manuel utilisateur

Universal

Universal UNV-15907 Manuel utilisateur