Cadel FRAME3 Guide de l'utilisateur

INSTALLER MANUAL

Pellet Stove

FRAME3- FRAME3UP - QUASIMODO3UP -MODO AIRTIGHT

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

SUMMARY

1 MANUAL SIMBOLOGY....................................3

2 PACKAGING AND HANDLING..........................3

2.1 PACKAGING .............................................................3

2.2 REMOVING THE STOVE FROM THE PALLET ..............3

2.3 STOVE HANDLING....................................................4

3 CHIMNEY FLUE .............................................4

4 COMBUSTION AIR.........................................4

4.1 EXTERNAL AIR INLET...............................................4

4.2 COMBUSTIBLE AIR INLET FOR SEALEDCHAMBER

INSTALLATION ...................................................................5

4.3 COMBUSTIBLE AIR INLET FOR SEALEDCHAMBER

INSTALLATION ...................................................................5

5 INSTALLATION..............................................6

5.1 INTRODUCTION.......................................................6

5.2 OVERALL DIMENSIONS ...........................................6

5.3 GENERAL INSTALLATION.........................................8

5.4 MOUNTING MODO AT AND QUASIMODO3UP STAND9

5.5 MOUNTING MODO AT LEGS.....................................9

5.6 REMOVE SIDE PANELS FRAME3...............................9

5.7 REMOVESIDEPANELSMODOAIRTIGHT/QUASIMODO3

UP ..............................................................................10

5.8 DOOR ADJUSTMENT..............................................10

5.9 CONNECTION TO THE EXTERNAL THERMOSTAT.....11

5.10 ELECTRIC CONNECTION.........................................11

5.11 AIR REGULATOR ....................................................11

5.12 FRAME3AND QUASIMODO3HOT AIR DUCTING

OPTIONAL .....................................................................12

5.13 MODO AIRTIGHT CONCENTRIC PIPE INSTALLATION14

5.14 STOVE CALIBRATION AND DEPRESSION

MEASUREMENT ...............................................................16

6 SPECIAL MAINTENANCE ..............................16

6.1 INTRODUCTION.....................................................16

6.2 FEED SCREW MAINTENANCE.................................17

6.3 FUME FAN CLEANING............................................17

6.4 FUME CONDUIT CLEANING....................................18

6.5 FUME PIPES ANNUAL CLEANING .........................19

6.6 GASKET REPLACEMENT.........................................19

7 IN CASE OF ANOMALY..................................19

7.1 PROBLEM SOLVING ...............................................19

8 TECHNICAL DATAS ......................................22

8.1 FUSE REPLACEMENT .............................................22

9 FEATURES ..................................................23

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

1 MANUAL SIMBOLOGY

USER

AUTHORISED TECHNICIAN

(ONLY to interpret or the Stove-manufacturer or the Authorized Techni-

cian of Technical Assistance Service approved by the Stove-manufacturer)

SPECIALIZED STOVE-REPAIRER

CAUTION:

READ CAREFULLY THE NOTE

CAUTION:

DANGER OR IRREVERSIBLE DAMAGE POSSIBILITY

• The icons with the stylized figures indicates whom the subject dealt in the paragraph is addressed to (between the User and/

or the AuthorizedTechnician and/or the Specialized Stove-repairer).

• WARNING symbols indicates an important note.

2 PACKAGING AND HANDLING

2.1 PACKAGING

• The packaging is made up of recyclable cardboard boxes according to RESY standards, recyclable expanded polystyrene inserts

and wooden pallets.

• All packaging materials can be re-used for a similar use or eventually discharged as waste assimilable to the municipal solid

ones, in accordance with current regulations.

• After having removed the packaging please assure you about the integrity of the product.

2.2 REMOVING THE STOVE FROM THE PALLET

Proceed as follows to remove the stove from the pallet:

Fig. 1 - Remove the screws + brackets

• Remove the screws of the 2 brackets securing the stove (see Fig. 1).

• Then remove the stove from the pallet.

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

2.3 STOVE HANDLING

Both whether the stove is packed or not it is necessary to observe the following instructions for handling and transporting the

stove from its sale point to its installation point and for any future movements:

• The stove must be handled with idoneous means paying attention to the existing safety regulations;

• do not turn the stove upside down and/or upset it on one side, but keep it in vertical position or as accorded with the construc-

tor instructions;

• if the stove is made up of ceramic, stone, glass or any particularly fragile material components, all must be moved with the

utmost care.

3 CHIMNEY FLUE

4 COMBUSTION AIR

4.1 EXTERNAL AIR INLET

Fig. 2 - Direct air inow

LEGEND Fig. 2

1Room to ventilate

2External air inlet

• The room must be endowed with an external air recycling for a good climate in your ambient.

• The air inflow from outside to the inner occurs directly, through an opening on the external wall of the room (see Fig. 2).

• Bedrooms, garages, and store of flammable materials are excluded.

• The air inlet should have a total net surface of 80 sqcm2: the aforesaid surface is to widen if inside the room there are other

activated appliances (for example: electric ventilators for foul air suction, cooker hoods, other stoves, etc...) which depress the

environment.

• At switched on appliance it is necessary to check that the pressure fall between the room and the outside does not exceed 4,0

Pa value: if necessary widen the air inlet (EN 13384).

• The air inlet must be realized at a height close to the floor with an external grid against birds. In such a way it cannot be ob-

structed by any object.

• In case of installation with sealed-chamber the air inlet is not necessary.

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

4.2 COMBUSTIBLE AIR INLET FOR SEALEDCHAMBER INSTALLATION

Fig. 3 - Air inlet for sealed-chamber installation

LEGEND Fig. 3

1≥ 1,5 mt

2≥ 0,3 mt

3-3 Sectional view

4Shield grid

5Curve inlet to turn downwards

Check if the purchased stove has a sealed-chamber. If the stove is endowed with a sealed-chamber and you want also the whole

installation with sealed chamber, please read the following instructions:

• It is necessary to extract the air for combustion directly from outside.

• Use a tube with minimum Ø60 mm and maximum 2 meters lenght; to connect see the back of the stove.

• French standards require installation in double-walled flues (concentric system). The combustion air is drawn from the cavity.

• During installation step is necessary to verify the minimum distances required for the combustible air inlet as (for example)

an open door or window causes a vortex which could remove the combustible air necessary to the stove (see the underlying

scheme).

• On the external wall it is necessary to install a curve at 90° to protect the combustible air inflow from wind effects: turn the

curve inlet downwards, see Fig. 3.

• Endow the curve with an external shield grid against birds in such a way that it cannot be obstructed by any object.

Check with your local authorities if exists any restrictive regulation regarding the combustible air inlet: if pre-

sent, they must be applied

In some countries and/or regions the installation with sealed-chamber is obligatory: in case of doubt, please

follow the most restrictive regulations.

4.3 COMBUSTIBLE AIR INLET FOR SEALEDCHAMBER INSTALLATION

How to connect to the stove in the sealed chamber with concentric system:

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

Fig. 4 - Phase 1

• Insert the female tube ø 6 cm (see Fig. 4).

5 INSTALLATION

5.1 INTRODUCTION

• The assembly position must be chosen depending on environment, outlet, chimney flue.

• Check with local authorities if there are any restrictive regulations which regard the combustible air inlet, room ventilation,

fume exhaust system together with chimney flue and chimney pot.

• Check if there is the combustible air inlet.

• Check the probable presence of other stoves or appliances which could depress the room.

• Check at switched on stove if there is the presence of CO in the room.

• Check if the chimney has the necessary draught.

• Check if during the fume passage all has been executed in safety (probable fume losses and distances from flammable mate-

rials, etc.…).

• The installation of the appliance must enable an easy access for appliance, fume exhaust pipes and chimney flue cleaning.

• The installation must enable en easy access to the electric connection plug (see ELECTRIC CONNECTION a pag. 11).

• To install more appliances, the external air inlet must be correctly dimensioned (see FEATURES a pag. 23).

5.2 OVERALL DIMENSIONS

Fig. 5 - General dimensions: FRAME3

LEGEND Fig. 5

170,3 cm 836,4 cm

278 cm 921,2 cm

353 cm 10 Exhaust fumes d.8 cm

420,3 cm 11 Hole combustion air inlet d.6 cm

515,4 cm 12 Ducting outlet d.8 cm (optional)

616,7 cm 13 Hot air outlet 32x2 cm

736,7 cm

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

Fig. 6 - General dimensions: FRAME3UP

LEGEND Fig. 6

170,3 cm

283 cm

361 cm

435,1 cm

512,5 cm

636,4 cm

721,2 cm

8Exhaust fumes d.8 cm

9Hole combustion air inlet d.13 cm

10 Ducting outlet d.8 cm (optional)

11 Hot air outlet 32x2 cm

Fig. 7 - General dimensions: QUASIMODO3UP

LEGEND Fig. 7

170 cm 835 cm

298,5 cm 910,6 cm

356,4 cm 10 17,3 cm

442,5 cm 11 71,2 cm

560 cm 12 Exhaust fumes d.8 cm

656,4 cm 13 Hole combustion air inlet d.13 cm

747,5 cm 14 Ducting outlet d.8 cm (optional)

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

Fig. 8 - General dimensions: MODO AT

LEGEND Fig. 8

170 cm

256 cm

358 cm

442,5 cm

535 cm

610,6 cm

7Exhaust fumes d.8 cm

8Hole combustion air inlet d.13 cm

970 cm

10 30 cm

11 60 cm

12 42,5 cm

13 65 cm

14 30 cm

5.3 GENERAL INSTALLATION

Fig. 9 - General installation

LEGEND Fig. 9

1Stove

2Minimum lateral distance = 200 mm

3Minimum rear distance = 200 mm

4Minimum front distance = 1000 mm

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

It is obligatory to install the stove away from walls and/or pieces of furniture, with a minimum air flow of 200 mm on the sides and

200 mm on the back, to enable an efficient appliance cooling and a good distribution of heat in the room (see Fig. 9).

If the walls are made up of flammable materials, check the safety distances (see Fig. 9).

At maximum power check that the wall temperature does not ever exceed 80°C. If it would be necessary please install a fire re-

sistant plate on the concerned walls.

In some countries also masonring load-bearing walls are considered flammable.

5.4 MOUNTING MODO AT AND QUASIMODO3UP STAND

Assembly operations must always be carried out by 2 people!

Proceed as follows to assemble the stand:

Fig. 10 - Stand fastening

• Set the machine body above the stand and fix it all with the supplied screws (see Fig. 10).

5.5 MOUNTING MODO AT LEGS

Assembly operations must always be carried out by 2 people!

To assemble the legs, proceed as follows:

Fig. 11 - Position base and legs Fig. 12 - Fasten legs to the base Fig. 13 - Stove fastening

• Set the base on a flat surface (with the bend facing upwards) and position it above the legs (see Fig. 11).

• Secure the legs to the base (see Fig. 12).

• Set the machine body above the legs and fix it all with the supplied screws (see Fig. 13).

5.6 REMOVE SIDE PANELS FRAME3

Proceed as follows to remove the stove side panels:

FRAME3 - FRAME3 UP - QUASIMODO3 UP - MODO AIRTIGHT

Fig. 14 - Remove the screws Fig. 15 - Unhook the side

• Loosen the 2 screws (see Fig. 14).

• Release the 2 teeth on the bottom of the side panel and remove it (see Fig. 15).

5.7 REMOVE SIDE PANELS MODO AIRTIGHT / QUASIMODO3UP

Proceed as follows to remove the stove side panels:

Fig. 16 - Remove the screws Fig. 17 - Unhook the side

• Loosen the 2 screws (see Fig. 16).

• Release the 2 teeth on the bottom of the side panel and remove it (see Fig. 17).

5.8 DOOR ADJUSTMENT

To centre the door, proceed as follows:

Fig. 18 - Door adjustment

• Open the door.

• Loosen the two front screws in the upper hinge and, using the side screw (the one circled in the picture) adjust the door

Autres manuels pour FRAME3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cadel Poêle

Cadel

Cadel VENUS Guide de démarrage rapide

Cadel

Cadel PRINCE3 11KW- GLOBE AIRTIGHT SFERA3 PLUS... Guide de l'utilisateur

Cadel

Cadel ARCO 7 T1 Guide de l'utilisateur

Cadel

Cadel LORD 7 Guide de l'utilisateur

Cadel

Cadel family Manuel utilisateur

Cadel

Cadel Martina Manuel

Cadel

Cadel SHELL3 UP Guide de l'utilisateur

Cadel

Cadel WALL3 PLUS Guide de l'utilisateur

Cadel

Cadel RIVERIDRO 16 T2 Guide de l'utilisateur

Cadel

Cadel INDIGO EVO Guide de l'utilisateur

Cadel

Cadel IDRO PRINCE 3 12 Guide de démarrage rapide

Cadel

Cadel RIVER IDROTECH 18 Guide de l'utilisateur

Cadel

Cadel SOUND3 5 UP Guide de l'utilisateur

Cadel

Cadel SFERA3 11KW Guide de l'utilisateur

Cadel

Cadel GO 11 Guide de l'utilisateur

Cadel

Cadel ARCO 7 T1 BI-FLUX Manuel utilisateur

Cadel

Cadel SWEET3 7 Manuel utilisateur

Cadel

Cadel KOBE 11 Manuel utilisateur

Cadel

Cadel INDIGO Manuel utilisateur

Cadel

Cadel aquos 15 Instructions d'installation et d'utilisation

Cadel

Cadel VERA 7 Manuel utilisateur

Cadel

Cadel IDRO PRINCE3 12 Guide de l'utilisateur

Cadel

Cadel SATURNO 16 Guide de l'utilisateur

Cadel

Cadel AMARANTO 9 Guide de l'utilisateur

Manuels Poêle populaires d'autres marques

Arada

Arada Cassette Stove Manuel utilisateur

Parmco

Parmco FS 600 Manuel utilisateur

MCZ

MCZ SUITE AIR 10 M2 Manuel utilisateur

HearthStone

HearthStone Stowe DV 8321 Guide de dépannage

Cattara

Cattara FAMILY Manuel utilisateur

Stanley

Stanley Argon F500 OVAL Manuel utilisateur

Avalon

Avalon B-VENT Manuel utilisateur

Nordpeis

Nordpeis Vega Manuel utilisateur

Exquisit

Exquisit EKC601-5 Manuel d'utilisation

Stanley

Stanley Oisin Oil MK II Manuel du propriétaire

Thermocet

Thermocet Brookfield S/CC Manuel utilisateur

HASE

HASE delhi Manuel utilisateur

Vermont Castings

Vermont Castings Intrepid 2 Manuel utilisateur

Italiana Camini

Italiana Camini CLASSICA Guide de démarrage rapide

Avalon

Avalon Vashon Avanti DVS FS Manuel utilisateur

Spartherm

Spartherm ambiente a1 Manuel utilisateur

Dimplex

Dimplex MCFSTV12AU Manuel utilisateur

Warmlite

Warmlite WL46040 Manuel utilisateur