CAB FABY 2 Manuel utilisateur
Manual n° 151010 Ott. 2010
SERVICE MANUAL
FABY
2
MODEL
C.A.B.
- Via Campana, 233 - Pozzuoli (NA) 80078 - ITALY
S.p.A.
Before using the machine please read this manual carefully.
Please note that non-compliance to the manual releases the manufacturer from any responsibility.
The machine must not be used for purposes other than the ones shown in this manual. Any improper use of
the machine will nullify warranty conditions. The slush machine should not be placed close to explosive or
fire hazards and should be installed in accordance with local fire and electrical codes. This manual provides
basic infomation about the slush machine. The illustrations and specifications are not binding in the tile.
We reserve the right to make changes to the slush machine without notice, and without incurring any
obligation to modify or provide new parts for slush machine built prior to date of change. Do not attempt to
service or operate the slush machine until instructions and safety precautions in this manual are read
completely and are thoroughly understood. If problems develop or questions arise in connection with
installation, operation or servicing of the slush machine, contat your distributor.
The slush machine has been assembled, operated and inspected at the factory. Upon arrival at the final
destination, the complete slush machine must be checked for any damage which may have occurred during
transit.
With the method of packaging used, the slush machine should arrive in excellent condition. The carrier is
responsible for all damage in transit, whether visible or concealed.
Installation of the slush machine involves moving the slush machine close to its permanent location;
removing all crating, setting in place, assembling parts and cleaning.
SHIPMENT and TRANSIT
INSTRUCTION MANUAL
MODEL 1 MODEL 2 MODEL 3
ELECRTICAL
POWER ABSORBED
BOWL
Dimensions
WIDTH
DEPTH
HEIGHT
NET WEIGHT
GAS
1 phase,
115Vac
60 Hz
1 phase,
115Vac
60 Hz
1 phase,
115Vac
60 Hz
530 W 850 W 1100 W
2.75 gallon 2.75 gallon 2.75 gallon
7.87 “ 15.75 “ 23.62 “
18.90 “ 18.90 “ 18.90 “
33.08 “ 33.08 “ 33.08 “
66 lbs
R404a
5.3 oz
114.40 lbs
R404a
10.94 oz
154 lbs
R404a
13.75 oz
Pic. 3
Height
Pic. 1
Pic. 2
Widht
Depht
8 inches
8 inches
8 inches
2
Place machine on a flat surface. Leave at least 8 inches on all sides for air circulation
to avoid overheating. Optimum room temperature range: 77° F - 90° F.
The slush machines are equipped with air-cooled condenser and require correct
ventilation. The left side is the air intake and must be unobstructed. Air discharge out
is on the right side. Do not obstruct the discharge.
Pic. 4
Pic. 6
Pic. 7
Pic. 5
Pay attention to the voltage. Be sure
there is a ground pole. Do not plug more
than one machine in to one socket.
Extensions cords not recommended.
GENERAL USE OF THE MACHINE
3
INSTALLATION OF THE MACHINE
Adjustment for slush consistency
Remove the mini door for slush adjustment (see pict. 8) on the back part of machine.
Rotate clockwise in order to increase the thickness.
Rotate counterclockwise in order to decrease the thickness of the slush (see pict.9).
The machine has been adjusted for fruit granitas (normal).
Products containing milk, or other products which may take longer to freeze, adjust
“+” as shown in picture.
-+
SLUSH
ADJUSTMENT
WHEEL
NORMAL MEDIUM MAXIMUM
Pic. 8
Pic. 9
Pic. 10
4
Mix product in a separate container if your product is a liquid concentrate, or powder,
to be mixed with water, do not dilute more.
There must be at least 18% sugar content to avoid breakage of ice scraper blade.
Pour syrup into the tank and set the level of liquid between MIN and MAX (Pic. 16).
Do not let product go below “MIN” line (keep at least 1" above cylinder at all times).
Refill with refrigerated product when level is halfway between min and max levels
(Pic. 16). This way there will always be frozen product available for customers.
Attention: do not pour hot product in the tank.
INSTALLATION OF THE MACHINE
Pic. 13
Pic. 12
Pic. 15Pic. 14
lift the upper lid gently and put it on one side of the machines drip tray panel by using
the appropriate hook (see pict. 11, 12 & 13).
Never turn machine on without product in bowl or with only water in bowl.
18% sugar
Pic. 16
Pic. 11
5
CONTROL PANEL
FUNCTION OF TIMER
Before starting the machine it is necessary to
set the timer.
W
TIMER PROGRAMMING
The TIMER switch, ( ) as shown in picture 19,
assembled on the control panel starts the night
function (cold drink dispenser).
(Day & Night Function)
For example, to have the machine work for slush
(Day function) from 7:00 AM to 11:00 PM, push
inwards all segments included in those hours, as
shown in Picture 19. During the remaining hours
the machine will work as a cold drink dispenser
(Night function).
.
Set the triangle of the timer on the right local time.
Please noteAM - PM signs (pic. 19).
After timer setting it is possible to start the
machine with some simple operations.
Without the correct time setting, the timer
will not work properly.
Turn on the INDIVIDUAL BOWL FREEZE
switches (C) as shown in picture 19.
Turn on the MAIN POWER switch (A) as shown in
picture 19. The
Turn on the LIGHT switch (B) as shown in picture
19
N.B.:
INSTRUCTIONS TO START THE MACHINE
main power switch starts all
BOWL UPPER AGITATOR and main gear-motor
too.
Pic. 19
To operate on the
machine's switches
open the cover for
control panel with the
lock key.
After settings of the
machine's desired
functions please lock
the panel and keep the
key in a safe place (see
Pic. 17 & 18).
Pic. 17
Pic. 18
A
W
C
C
B
Pic. 24
Pic. 26 Pic. 27
6
CLEANING OPERATION
Pic. 25
Place fingers under the front lower part
of the bowl, near the tap, and push
upwards until legs pop out.
Turn power off.
Drain product. Fill bowl with tepid water, and wait 15 minutes (see Pict.24 & 25).
To continue cleaning operation empty the bowl again.
Place fingers behind the bowl legs and
pull the bowl onwards slowly until it has
been completely removed.
For an easy removal of the bowl. Please follow instructions shown in Pictures
26 & 27.
ATTENTION: Place all the components in a safe place in order to be sure they are not lost.
NOTE: Do not use too hot water to clean the plastic components .
Clean the components with dish-washing soap and tepid water. Never use abrasive cleaners.
Pic. 28 Pic. 29
Pic. 30 Pic. 31
CLEANING OPERATION
7
To remove spiral blade put fingers on the plate part of the spiral and pull it onwards
gently as shown in Pict. 28 & 29.
Remove bowl gasket from the back part
of the evaporator tube (see Pict. 31).
Once the spiral blade is removed
completely remove the suction cap
gasket from the front spiral as shown in
Pict. 30
ATTENTION: Place all the components in a safe place in order to be sure they
are not lost.
NOTE: Do not use too hot water to clean the plastic components .
Clean the components with dish-washing soap and tepid water. Never use abrasive
cleaners.
Pic. 32
Pic. 35
CLEANING OPERATION
Pic. 33
How to remove and clean the tap components
1- Pull out the pin for handle fixing (see
Pict. 32).
2- Pull the handle from its place (see
Pict. 33).
3- Unthread the main tap pin by pulling
it downwards (see Pict.34)
4- Repeat the same operation for the
tap spring (see Pict. 35)
ATTENTION: Place all the components in a safe place in order to be sure they
are not lost.
NOTE: Do not use too hot water to clean the plastic components .
Clean the components with dish-washing soap and tepid water. Never use abrasive
cleaners.
Pic. 34
8
Pic. 39
Pic. 38
CORRECT INCORRECT
Reassembly of the parts removed during the cleaning.
Before reassebling of parts, clean the evaporapor tube and drip trays & grids without using abrasive
cleaners. Before reassemblyng the bowl gasket rinse it with water in order to facilitate the assembly
of the bowl.
Lubricate the front part of evaporator tube as indicated in Pict. 39/ . Insert the spiral blade by
pushing it gently and deeply as indicated in Pict. 40a & 40b. After this it is important to lubricate the
head of the spiral (see Pict. 34/ ).
1
2
1
Lubricate
2
REASSEMBLY OF THE COMPONENTS
Put the bowl gasket in its position on the back part of the evaporator tube.
Once the bowl gasket is in its right position press it with your thumbs first in the lower part and then
progressively towards its upper part (marking a circle with your fingers); until it is correctly fixed in its
site (see Pict. 36 & 37).
Insert the suction cap gasket into the
spiral blade by pushing it deeply (see
Pict. 38).
Lubricate with lubricanrs provided in the
machine like shown in Picture 38.
Pic. 36 Pic. 37
Pic. 40a
Pic. 40b
9
Table des matières
Autres manuels CAB Système de filtration d'eau
CAB
CAB MAESTRO 4S Manuel utilisateur
CAB
CAB MAESTRO 2M Manuel utilisateur
CAB
CAB MAESTRO 5L Manuel utilisateur
CAB
CAB HEKTOR 4 Manuel utilisateur
CAB
CAB MAESTRO 6 Manuel utilisateur
CAB
CAB MAESTRO 2M Manuel utilisateur
CAB
CAB MAESTRO 4S Manuel utilisateur
CAB
CAB MAESTRO 3E/450 Manuel utilisateur
CAB
CAB MAESTRO 3E Manuel utilisateur
CAB
CAB MAESTRO 2 Manuel utilisateur
Manuels Système de filtration d'eau populaires d'autres marques
Wisy
Wisy LineAir 100 Manuel utilisateur
Schaffner
Schaffner Ecosine FN3446 Series Manuel d'utilisation
Pentair
Pentair FLECK 4600 SXT Guide de l'utilisateur
H2O International
H2O International H20-500 Manuel utilisateur
Renkforce
Renkforce 2306241 Manuel utilisateur
Neo-Pure
Neo-Pure TL3-A502 Manuel utilisateur
