C.P. Electronics AT-BB-IN Manuel utilisateur

Product Guide

AT -BB -IN

RF inputunit

Overview

TheAT -BB-INInputUnitprovidesacontrolinterface

betweenalightingsystem andexternal devicessuchas:

Button/switch plates

Security systems

AV equipment

TheunitfeaturessevenVolt-freeswitchinputsthatcanbe

activatedbythecontactclosureofpush-buttons,switches,

or relays.

ActivatinganinputcausestheunittotransmitaRFcontrol

messagetootherdevices,triggeringvariousactionssuch

asrecallingascene,raising/loweringlightlevels,turning

overrideon/off,startingandstoppingsequences,etc.

The integral RF transceiver allows wireless communication

withother An-10®compatibleproducts.Allfunctionalityis

fully programmable using an infrared handset (e.g. the

UHS4orUNLCDHS)orPCcontrolsoftware.

Theunitispoweredeitherbytheinternalbatteryorviaan

external 12Vdcsupply.

Features

Front features

Back features

Infrared Receiver (IR)

Allowstheunittoreceiveprogrammingcommandsfroman

IR Handset (e.g. the UHS4) when IR Receive mode is

activated(seeConfigButtonandStatusLEDsbelow).

Config Button

PressthistoputtheunitintoIRReceivemode,enablingit

toreceiveprogrammingcommandsfromanIRHandset.

Status LEDs

These flash R ed and/or G reen to indicate the following:

IR Receive mode active at 1 second intervals

Valid setting received

Invalid setting received

Software reset received

Factory reset received

Battery (type CR2477)

Provides power to the unit if an external supply is not used.

Optional 12Vdc Supply Terminal

Topowertheunitfromanexternalsupply,connectthe

supplytothisterminalensuringcorrectpolarity.Referto

TechnicalDataonpage8forpowersupplyspecification.

Plug -in RJ45 lead and socket

Ashort8coreflatcablewithplugthatissuppliedwitheach

unit,usedtoconnecttheinputstoexternaldevices.

Installation

The AT-BB-IN Input Unit can either be mounted to any

suitable solid surface or concealed inside a backbox.

Surface Mounting Method

Fit the two snap-on mounting brackets on the back side of

the unit as shown in opposite.

Use the holes in the mounting brackets to affix the unit to a

wall or other solid surface using suitable screw fixings.

Backbox Mounting Method

For unsecured fixing, the unit can be simply placed inside

a UK or European backbox (without fitting the snap-on

mounting brackets). This enables a proprietary switch

plate to be connected and screwed to the backbox.

Alternatively, for secured fixing, fit the two snap-on

mounting brackets on the front side of the unit as shown

opposite. The unit can then be secured to the backbox

using suitable fixing screws (up to M3.5).

NOTE: The mounting bracket holes are spaced to suit

either a UK (60.3mm pitch) or European (60mm pitch)

backbox.

CAUTION: Do not over tighten the fixing screws as

this may cause the brackets to split.

Mounting bracket location

for surface mounting.

Mounting bracket location for

secured backbox mounting.

Electrical connection

Connections to the AT-BB-IN Input Unit are made via the

RJ45 lead supplied. The lead has 8 wires, comprising 7

switch inputs plus a common connection (see below).

Connect the lead wires to suitable push-buttons or switches

as required (see wiring examples on page 3).

Each input has two possible states:

•Inactive when the input is unconnected

(i.e. open circuit), and

•Active when the input is connected to common,

(i.e. during button or switch closure).

Each input can be configured (using the Switch Type

parameter) for use with either momentary or latching type

buttons and switches.

•Momentary operation is the default, used for normally-

open push-buttons or centre-retractive type switches.

•Latching operation is typically used for toggle type

switches that remain in either a closed or open state.

IMPORTANT NOTE: Latching Mode is not suited to battery

operation due to the continuous current drain while a switch

is closed. An external 12V power supply must, therefore,

be connected if Latching Mode is used.

Input connection identification

• •

3 - Input 3

Yellow

4 - Input 4 Green

5 - Input 5 Red

6-lnput6

Black

7 - Input 7

Orange

8- Common Grey

•

Wiring examples

Example 1: Using individual push-buttons

RJ45 Lead

1 - Input 1 Brown

•

Example 2: Using centre retractiveswitches

RJ45 Lead

1 - Input 1 Brown 0

0 2 - Input 2 Blue 0

0 3 - Input 3 Yellow 0

04 - Input 4 Green 0

0 5-lnput5 Red 0

0 6 - Input 6 Black 0

0 7 - Input 7 Orange 0

NC---0

8 - Common Grey

Example 3: Using latching switches (for use with external 12Vdc supplyonly)

RJ45 Lead

0 1 - Input 1 Brown 0

2 - Input 2 Blue

0 0

IMPORTANT NOTE:

Latching Mode is not suited to

battery operation due to the

continuous current drain while a

switch is closed. An external 12V

power supply must, therefore, be

03 - Input 3 Yellow 0

04 - lnput 4 Green 0

5 - Input 5 Red

6 - Input 6 Black

0 7 - Input 7 Orange 0

8- Common Grey

connected if Latching Mode is used.

•

Input

Basic programming

The functionality of the AT-BB-IN Input Unit is controlled

by a number of parameters which can be changed or

programmed by any of the following devices:

•UHS4 Infrared Handset

•UNLCDHS Infrared Handset (with LCD)

For most basic programming operations the UHS4 handset

is recommended and the following procedures are based

on using this device.

Step 1: Put Input Unit in receive mode

To enable the AT-BB-IN Input Unit to receive programming

commands it must be put into receive mode by pressing

the Config Button.

While the unit is in receive mode send the required

programming commands to the unit (see Step 2 and 3).

Valid commands will be indicated by a green LED flash.

See page 1 for details of other LED responses.

NOTE: While in receive mode, if no commands are

received by the Input Unit within 30 seconds, the unit will

automatically revert to its normal standby mode.

Step 2: Set input channel addresses

The addressing for an input channel defines the devices

that will respond to any control messages sent by the

input unit.

For example, activating an input that has its Local Code

set to 1, generates a control message that will only be

actioned by devices that also have a Local Code of 1.

To program the settings for a specific input channel you

must specify the appropriate channel number (i.e.1 to 7)

using the programming device.

If no channel number (or channel 0) is specified, all input

channels will be set to the same address.

Basic programming

Step 3: Choose a presetconfiguration

To simplify the programming of commonly used

applications, a number of Preset Configurations are

available. Preset 0 is implemented by default.

HINT: Where scene numbers or channel numbers are

given in a Preset Configuration, these can be changed

(after applying the Preset) by using the Map Scene/

Channel to Button/Input command.

Refer to the UHS4 user instructions for further assistance.

Circuit mode

Toggle=On/off/raise/lower

Preset No.

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

Function

On / up

Off / down

On / up

Off / down

On / up

Off / down

Em Test

(default)

Circuit

Switch type

Function

Off

Em Test

Circuit

Switch type

Function

Toggle

Em Test

Circuit

Switch type

Function

On/off

Em Test

Circuit

Switch type

Scene mode

Toggle=On/off/raise/lower

Preset No.

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

Function

Down

Off

Scene

Active scene

Off

Switch type

Function

On / up

Off / down

On / up

Off / down

On / up

Off / down

Off

Scene

Off

Switch type

Function

Toggle

Off

Scene

Off

Switch type

Function

On/off

Off

Scene

Off

Switch type

Key—switch types

M Momentary push to make switch

L Latching switch

Limited to Preset Configurations

Advanced programming

Input Behaviour

Changes in the state of an input (e.g. from inactive to

active) generate different events that can then be used to

trigger various control functions.

The events generated depend on whether momentary or

latching mode is selected (via the Switch Type parameter).

Momentary Mode Operation

In this mode the input is usually inactive (open circuit) and

only active (shorted to common) when the button or switch

is pressed. This gives rise to four possible input events:

•Single Press

•Double Press

•Long Press – Hold (switch closed for longer than300ms)

•Long Press – Release (switch opened after Long Press –Hold)

Latching Mode Operation

This mode is typically used for toggle type switches that

remain in either a closed or open state for long periods.

Latching mode, therefore, gives rise to two possible events:

•Pressed (switch closed)

•Released (switch open)

Control Functions

Each type of input event can be used to trigger any of the

following control functions:

•Scene Select

used to select a specific lighting scene. Depending on

the input channel addressing both Local and/or Area

scenes can be selected.

•Scene Raise or Lower

used to increase or decrease the overall lighting levels

for the currently active scene.

•Circuit Absolute Level

used to set the level of a specific output channel.

•Circuit Raise or Lower

used to increase or decrease the level of a specific

output channel.

•Sequence Control

used to start, stop or pause a sequence of scenes.

•Override Control

used to select global override scenes, typically during

emergency situations (e.g. fire evacuation).

•Emergency Test

used to test device/systems for correct operation during

a mains power failure.

The table below and on page 7 gives a summary of all

programmable parameters for the AT-BB-IN Input Unit.

Parameter Name Default Value Range / Options Description

Programming

Devices

UHS4 UNLCDHS

For Device

Product ID Automatically

assigned by the

device

1 to 999 A number used to uniquely identify each device within a range of

devices that are set to the same Local Code. 



Building Code

1 to 999 A number shared by all devices that belong to the same building or

system. 



For Each Input Channel

Switch Type Momentary Momentary, Latching Defines whether the input is used in conjunction with momentary or

latching type switches. Also defines the range of events available

for triggering control functions.

*



Local Code

1 to 999 A number corresponding to the Local Code of all devices to be con-

trolled by the associated input channel. 



Sub Local Code Not set 1 to 99

0 to clear A number corresponding to the Sub Local Code of all devices to be

controlled by the associated input channel. 



Area Code(s) Not set 1 to 999 A number corresponding to the Area Code of all devices to be con-

trolled by the associated input channel. Up to 10 Area Codes can

be set for each input channel.



For Each Input Event

Control Function As per Preset 0 None (do nothing)

Scene Select

Scene Raise

Scene Lower

Circuit Absolute Value

Circuit Raise

Circuit Lower

Sequence Control

Override Control

Emergency Test

Defines the type of radio control message sent to other devices. *



Advanced programming

* Limited to Preset Configurations 7

Parameter Name Default Value Range / Options Description

Programming

Devices

UHS4 UNLCDHS

Control Function = Scene Select

Local On Scene

Fade Rate

Timeout

1 second

255

1 to 20

0 to 255*

A Scene Select message comprises of three Local Scenes (On, Step

and off) and three Area Scenes (On, Step and off)

When a Scene is selected the input unit recalls the Local and/or Area

On Scenes.

If a Local and/or Area Step Scene is specified this will be requested first

followed by the Local and/or Area Off Scenes.

NOTE: Area On, Step and Off Scenes are ignored unless one or more Area Codes

are set for the corresponding input channel and they match the Area Codes set in

any output channel.

The values of the Timeout parameters associated with each scene

determine whether or not the scene is actually recalled and whether or

not to try and recall the next scene:

Time / delay table

Value Fade rate time Timeout delay period

No fade Ignore the Stepscene

to 59 1 to 59 seconds, in 1 1 to 59 seconds, in 1 secondincre-

second increments ments

60 to 177 1 to 59.5 minutes, in 0.5 1 to 59.5 minutes, in 0.5 minute incre-

minute increments ments

178 to 254 1 to 20 hours,in 15 1 to 20 hours, in 15 minute incre-

minute increments ments

255 Infinite fade No timeout recall the specified scene

only

*



Local Step Scene

Fade Rate

Timeout

1 second

255

1 to 20

0 to 255*

Local Off Scene 20 1 to 20

Area On Scene

Fade Rate

Timeout

101 to 107

1 second

255

101 to 220

0 to 255*

Area Step Scene

Fade Rate

Timeout

101 to 107

1 second

255

101 to 220

0 to 255*

Area Off Scene 220 101 to 220

Control Function = Scene Raise

Raise Action Not set Start or none Starts (or stops) raising light levels for the currently active Scene.

Typically used with a Long Press Hold (to start) and Long Press Release

(to stop).

*



Control Function = Scene Lower

Lower Action Not set Start or none Starts (or stops) lowering light levels for the currently active Scene.

Typically used with a Long Press Hold (to start) and Long Press Release

(to stop).

*



Control Function = Circuit Absolute Level

Circuit Number As per Preset 0 1 to 999 Sets the target output level for the specified Circuit Number to the value

given by Output Level. The time taken for the output to fade to the new

level is set by the Fade Rate.





Output Level 100% (on)

0% (off) 0 to 100%

Fade Rate 1 second 1 to 60 seconds

Control Function = Circuit Raise

Circuit Number As per Preset 0 1 to 999 Starts (or stops) raising the output level of the specified Circuit Number.

Typically used with a Long Press Hold (to start) and Long Press Release

(to stop).

*



Raise Action As per Preset 0 Start or none

Control Function = Circuit Lower

Circuit Number As per Preset 0 1 to 999 Starts (or stops) lowering the output level of the specified Circuit

Number. Typically used with a Long Press Hold (to start) and Long

Press Release (to stop).

*



Lower Action As per Preset 0 Start or none

Control Function = Override Control

Override Type Not set On, off Selects whether the Override On or Override Off global scene is to be

applied or released. 



Override Action Not set Active or released Sets the specified Override global scene active or releases it.

Control Function = Sequence Control

Sequence Number

1 to 99 Selects the Sequence Number to be controlled. 



Sequence Action Not set Start, stop or

pause Selects the action to be applied to the specified Sequence.

Control Function = Emergency Test

Test Condition Not set on or off Turns the Emergency Test feature on or off. *



On Test Timeout Not set 0 to 255 Sets the maximum On Test time before the feature is automatically

turned off. (See note on Timeout values above).

ReplacingtheBattery

Press -inthelargeretainingclipsuffi cientlytoallow thetwo

halvesof thecasingtobeseparated.

LiftoutthePCBmodule,takingcarenottodamagethe

electronic components.

Slide out the battery from its mounting clip and insert a

replacement battery (type CR2477 or equivalent), ensuring

correct polarity.

Carefullyreassembletheunit,ensuringthatthethree

retaininglugsarecorrectlylocatedbeforeclippingthe

casing backtogether.

Accessing the internal battery

Technicaldata

Weight 0.025kg

Battery 3Vdc lithiumbattery,

type CR2477 (supplied with unit)

BatteryLife Greaterthan7yearswithtypical

usage

Optional External Supply Requirements:

SupplyVoltage 12Vdc regulated

SupplyCurrent 50mAmax.

SupplyPower 600mW max.

TerminalCapacity

2.5mm2

ReceiverClass 2

TransmitterDutyCycle <10%ong3band(defaultband)

<0.1% on g2 band

<1% on g1 band

Range The maximum RF range between An -10

devices is 100m in free air and up to 30m

indoors.Howeverthematerialsusedwithin

abuildingwillvaryandthiswillimpactupon

theRFrange.Inrealitythenatureofhow

theAn-10’shybrid-meshworksmeansthat

inmostscenariostheindividualrangeofan

An-10product willnot beimportant.

Temperature 0ºC to35ºC

Humidity 5 to 95% non -condensing

Material(casing)

Flame retardant polycarbonate

Dimensions - without brackets

Dimensions - with brackets

Hereby,CPElectronicsLtd,declaresthatthis AT

-BB-IN is incompliancewiththeessential

requirements and other relevant provisions of Directive 1999/5/EC. The declaration ofconformity

maybeobtainedforCPElectronicsLtdBrentCrescent,London,NW107XR,UK.

Partnumbers

EBDSPIR -AT-PRM RFCeilingPIRpresencedetector

– switched

EBDSPIR -AT-DD RFCeilingPIRpresencedetector – DALI/DSI dimming

EBDSPIR -AT-AD RFCeilingPIRpresencedetector

– 1-10V dimming

AT-SL-R RF relaycontroller

AT-SL-R-SA

RFrelaycontroller(standalone)

AT-SL-DDR

RFDALI/DSI +relaycontroller

AT-SL-DDR-SA RFDALI/DSI+relaycontroller(standalone)

AT-SL-ADR

RF1 -10V+relaycontroller

AT-SL-ADR-SA RF1 -10V+relaycontroller(standalone)

VITM4 -ATMOD

RF Switchingmodule

VITM6-ATMOD-AD RFVITM61 -10Vmodule

VITM6-ATMOD-DD

RF VITM6 DALI/DSImodule

UNLCDHS

Universal LCDIRhandset

If any of these symbols are on the

product or battery, the product or battery

must be disposed of in the correct

manner and must not be treated as

household or general waste.

Unit 16

1 Talavera Road Macquarie

Park, NSW 2112

T: 1300 697 627

F: (02) 9887 1333

www.mysmart.com.au

Due to our policy of continual product improvement mySmart reserves the right to alter the specification of this product without prior notice.

Order

code Region Radio

frequency

Compliance

blank

European

Union 868MHz

EN300 220 -2 V2.1.2

EN301 489 -1 V1.8.1

EN301 489 -3 V1.2.1

-A2 Australia &

New Zealand

915MHz AS/NZS 4268:2008

Autres manuels pour AT-BB-IN

Table des matières

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur