Burster 2311 Manuel utilisateur

OPERATION MANUAL

Resistomat 2311

PROFINET Integration into TIA Portal

Manufacturer:

burster

praezisionsmesstechnik gmbh & co kg

burster

präzisionsmesstechnik gmbh & co kg

Talstr. 1 - 5

P.O. Box 1432

76593 Gernsbach

76587 Gernsbach

Germany

Valid from:

01.02.2023

Tel.: +49-7224-645-0

Applies to:

Resistomat 2311-VXX03

Fax.: +49-7224-645-88

Email: inf[email protected]om

www.burster.com

4426-2311PROFINETIAEN-5999-081530

2of 17

Contents

1Introduction................................................................................................................................................3

2Creating new project .................................................................................................................................4

3Installation of GSDML files.......................................................................................................................5

4Creation of network connections ............................................................................................................6

5Perform a measurement and read the measurement result .................................................................9

6Further Examples ....................................................................................................................................16

6.1 Writing of string data types...............................................................................................................16

3of 17

1 Introduction

This quick start guide describes an approach how you can configure the RESISTOMAT®2311 via TIA Portal

using the example of S7-1511 CPU. Please note that the samples here cannot be directly used in your

production line because they have beed extremely simplified to reach a better understanding. Therefore, you

may have to complete them by checking of status, error, length values etc.

Note: Please also note that you will have to use the RESISTOMAT®2311 PROFINET manual to get

futher information about input and output parameters (cyclic as well acyclic data transfer).

4of 17

2 Creating new project

1. Start the Totally Integrated Automation Protal, select Create New Project (a), assign the project a

name (b) and click Create (c):

2. Go to Devices & networks (a) on the left side select Add new device (b) and look for yor CPU (c).

Afterwards click the Add button (d).

5of 17

3 Installation of GSDML files

Note: Please make sure that your GSDML file is compatible to the field bus firmware in the Resistomat

2311. Also for compatibility reasons, uninstall all previous GSDML files of particular device if you

have any!

1. Go to Options→Manage general station description files (GSD) (a)

2. Navigate to your Resistomat 2311 GSDML directory (a) (you will find the GSD on

www.burster.com/en/download-area), select the GSDML file (b) and click Install (c)

6of 17

4 Creation of network connections

1. Double click Device Configuration (a) in the project tree und switch to Network view (b) :

2. Now select the Resistomat 2311 device in the catalog and drag & drop it into the working area (a):

7of 17

3. Please select an ethernet port on the S7 and hold the left mouse button down to connect the S7 with

Resistomat 2311 (a):

4. Change now to Network view (a) to assign a controller to the Resistomat 2311. Click on the link “Not

assigned” (b) of Resistomat 2311 and select your controller (c):

8of 17

IMPORTANT: Check if devices are also connected physically to the right ports. You find the port number

assignment in the section Port-Identification of Resistomat 2311 PROFINET manual

5. Change the device name in Device view →Properties →General →Ethernet addresses:

9of 17

5 Perform a measurement and read the measurement result

In this section, you will learn how to create a simple program to start and stop a measurement periodically

and display the measured resistance value with corresponding unit in a watch table. You will need to refer to

sections PLC inputs and PLC outputs of the RESISTOMAT®2311.

PROFINET manual to understand the meaning of inputs and outputs bytes.

1. Add the variables out_start, in_ready and in_error as shown below

Note: Please note: the addresses may be different. You have to check them in the Device view 

Device overview of the Resistomat®2311:

2. Expand the tree node Program blocks in the Project tree and double click Add new block:

10 of 17

3. Select in the new window Organization block (a) →Cyclic interrupt (b). Set the cyclic time to

3.000.000 µs (c). As language set SCL (d) and click OK:

4. Type in the following source code in the code field of the new block:

IF "out_start" =TRUE THEN

"out_start" := FALSE;

IF "in_error" = FALSE THEN

"read_meas_value"();

END_IF;

ELSE

IF "in_ready" = TRUE THEN

"out_start" := TRUE;

END_IF;

// Is measurement start set?

// Then reset it

// No error?

// Read the measurement value

// Is 2311 ready for a new measurement?

// Start a new measurement

Table des matières

Autres manuels Burster Instrument de mesure

Burster

Burster REISTOMAT 2x11 EtherNet/IP Manuel utilisateur

Burster

Burster RESISTOMAT 2329 Manuel utilisateur

Burster

Burster DIGIFORCE 9307 Manuel utilisateur

Burster

Burster DIGIFORCE 9307 Manuel utilisateur

Burster

Burster 9186-V Series Manuel utilisateur

Burster

Burster 8627 Manuel utilisateur

Burster

Burster DIGIFORCE 9307 Manuel utilisateur

Burster

Burster 9180 Manuel utilisateur

Burster

Burster 9181 Manuel utilisateur

Burster

Burster RESISTOMAT 2329 Manuel utilisateur

Burster

Burster 1427 Manuel utilisateur

Burster

Burster Resistomat 2316 Manuel utilisateur

Burster

Burster TRANS CAL 7270 Manuel utilisateur

Burster

Burster Resistomat 2316 Manuel utilisateur

Burster

Burster RESISTOMAT 2 11 Series Manuel utilisateur

Burster

Burster Resistomat 2323 Manuel utilisateur

Burster

Burster 24508 Manuel utilisateur

Burster

Burster DIGIFORCE 9311 Manuel utilisateur

Burster

Burster RESISTOMAT 2302-V001 Manuel utilisateur

Burster

Burster Resistomat 2316 Manuel utilisateur

Burster

Burster DIGIFORCE 9307 Manuel utilisateur

Burster

Burster 8524 Manuel utilisateur

Burster

Burster DIGIFORCE 9310 Manuel utilisateur

Burster

Burster 9163 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur