Burkert 8030 HT Manuel utilisateur
Instruction Manual
© Bürkert 2003-2011 Subject to technical change without notice
00449752_ 1105/0_Original_FR
ENGLISH
ENGLISH
1.1 Utilisation ..................................................................................................................................................................................................4
1.2 Precautions at installation and commissioning .........................................................................................................5
1.3 Conformity to standards ..............................................................................................................................................................5
2.1 Design and Measuring principle............................................................................................................................................6
2.2 Ordering table of electronic modules SE30 HT .......................................................................................................7
2.3 Dimensions (mm) ..............................................................................................................................................................................7
4.1 General recommendations .....................................................................................................................................................12
4.2 Mounting on the pipe ..................................................................................................................................................................12
ENGLISH
ENGLISH
4.3 Electrical connection ...................................................................................................................................................................13
4.3.1 Connector EN 175301-803 (type 2508, supplied) ...........................................................................13
4.3.2 Wiring of the frequency output: pulse version (transistor outputs NPN and PNP)...14
4.3.3 Wiring of the frequency output: sinusoidal version (coil output) ..............................................15
5.1 Description of the label of the sensor SE30 HT ..................................................................................................16
5.2 Flow-velocity-DN diagrams ..................................................................................................................................................17
5.4 Wiring example .................................................................................................................................................................................19
ENGLISH
ENGLISH
The sensor 8030 HT has been designed to measure the flow rate of
neutral or slightly aggressive solid-free liquids.
There will be no manufacturer warranty for damages caused by
unexpected handling or wrong usage of the device. The warranty on the
device becomes invalid if any modification or change is made on the
device.
ENGLISH
ENGLISH
- Always ensure the materials in contact with the medium to measure are
chemically compatible with this medium.
- To clean the device, only use chemically compatible products.
- Always protect the device from electromagnetic perturbations,
ultraviolet radiations and, when installed outside, from the effects of
climatic conditions.
EMC: EN 50081-1, 61000-6-2
Security: EN 61010-1
Vibration: EN 60068-2-6
Shock: EN 60068-2-27
ENGLISH
ENGLISH
The flow sensor 8030 HT is built up with an electronic module SE30 HT
associated to a fitting S030 HT with integrated metallic paddle-wheel.
The sensor detects the rotation of the paddle-wheel which produces a
signal whose frequency f is proportional to the flow rate Q.
Two electronic module versions with frequency output are available:
- either with 2 pulse outputs (transistor NPN and PNP), where f = K.Q
- or with one sinusoidal output (coil), where f = 2 K.Q
where f = frequency in Hz
K = K factor specific to each fitting in pulses/l,
Q = flow rate in l/s
The electrical connection is carried out via an EN 175301-803
connector.
SE30 HT
S030 HT
ENGLISH
ENGLISH
32
40
66
44
54
9
EN 175301-803
12-36 VDC Pulse: 1 transistor NPN + 1 transistor PNP EN 175301-803 connector 449694
None Sinus: 1 coil EN 175301-803 connector 449693
6 95.5
8 95.5
15 100.5
20 98
25 98
32 102
40 105.5
50 112
H
ENGLISH
ENGLISH
Pipe diameter DN6 to DN50 (DN65 on request); determine the appropriate diameter using the flow-
velocity-DN diagrams (see Annex)
Medium temperature -15 °C up to 125 °C
Medium pressure PN40 if Tfluid < 90 °C
PN25 if 90 °C < Tfluid < 125 °C
Medium viscosity max. 300 cSt
Rate of solid particles max. 1%
Measuring range 0,5 m/s to 10 m/s
Accuracy ≤ ±1 % of the full scale*, with calibration on site (for example, using the teach-in feature of a
transmitter 8025, remote version)
≤ ± (1 % of the full scale* + 3% of the measured value), with standard K factor
Linearity ≤ ± 0.5 % of the full scale*
Repeatability 0.4% of the measured value
Measuring element metallic paddle-wheel of the stainless steel S030 HT fitting
* full scale = 10 m/s
Power supply none
Output data up to 500 Hz, about 2.8 mV peak-to-peak/Hz when loaded with 50 kΩ
(frequency = 2 x K factor x flow rate; for the value of the K factor, refer to the instruction
manual of the fitting)
Cable length max. 5 m, shielded
ENGLISH
ENGLISH
Power supply 12-36 VDC, filtered and regulated
Current consumption ≤ 10 mA (no load)
Protection against
polarity reversal yes
Output data transistor NPN and PNP, open collector, 700 mA max., NPN output: 0,2-30 VDC and
PNP output: supply voltage (see example in the Annex)
frequency: up to 250 Hz (frequency = K factor x flow rate; for the value of the K factor,
refer to the instruction manual of the fitting)
Protection against
short-circuits yes
Cable length max. 50 m, shielded (up to 500 m depending on the cable impedance and the current
consumption)
Pulse or sinus version EN 175301-803 connector (type 2508, supplied)
Type of cable recommended shielded, wire section between 0.14 and 0.5 mm2
Housing / Cable gland PPS, glass fiber reinforced / PA
Fitting S030HT, paddle-wheel stainless steel
Bearings of fitting S030HT Iglidur
Seal / axis of fitting S030HT FKM / ceramics
Ambient temperature - pulse version: -15 to +80° C
(operating and storage) - sinusoidal version: -15 to +100° C
Relative humidity <80%, non condensated
Protection rating (housing) IP 65, connector plugged-in and tightened
ENGLISH
ENGLISH
19
234567810
4
8
20
-4
-8
-12
-16
-20
1
v.
%
+
3
P.
E.
S.
/
F.
/
E.
v.
%
M./ o.R./V.M.
1
v.
%
P.
E.
S.
/
F.
/
E.
16
12
with calibration on site
without calibration on site, but standard K factor
Medium velocity
in m/s
max. error %
F.S = Full scale
o.R. = of Reading (measured value)
These values have been determined in the following reference conditions: medium = water, water and ambient
temperatures = 20 °C, min. straight upstream and downstream distances respected, appropriate pipe dimensions.
Accuracy of the measures with (teach-in feature of a transmitter 8025 for instance) and without
calibration on site
Measuring error - % of the measure
Autres manuels pour 8030 HT
1
Table des matières
Langues :
Autres manuels Burkert Accessoires
Burkert
Burkert GENERIC 8400 Manuel utilisateur
Burkert
Burkert 8020 Low Power Instructions d'installation et d'utilisation
Burkert
Burkert 8220 Manuel utilisateur
Burkert
Burkert 8030 Manuel utilisateur
Burkert
Burkert 8223 Manuel utilisateur
Burkert
Burkert 2509 Manuel utilisateur
Burkert
Burkert S030 Manuel utilisateur
Burkert
Burkert MS05 Manuel utilisateur
Burkert
Burkert 8007 Manuel utilisateur
Burkert
Burkert 8020 Manuel utilisateur
Burkert
Burkert 8045 Manuel utilisateur
Burkert
Burkert 1060 Manuel utilisateur
Burkert
Burkert FULLBORE S056 Manuel utilisateur
Burkert
Burkert MS06 Series Manuel utilisateur
Burkert
Burkert 8020 Manuel utilisateur
Burkert
Burkert GENERIC 8400 Manuel utilisateur
Burkert
Burkert 2510 Manuel utilisateur
Burkert
Burkert MS09 Manuel utilisateur
Burkert
Burkert 8798 Manuel utilisateur
Burkert
Burkert S070 Manuel utilisateur
