burchland XTS Manuel de programmation
SILT FENCE INSTALLER
S I L T F E N C E I N S T A L L E R
OPERATOR & PARTS MANUAL
TABLE OF CONTENTS
SAFETY
GENERAL SAFETY PRECAUTIONS………………………………………2-5
SAFETY DECAL PLACEMENT……………………………………………..6-7
SAFETY DECALS…………………………………………………………..8-10
OPERATION ………………………………………………………………………11-19
MAINTENANCE ……………………………………………………………………...20
WARRANTY
LIMITED WARRANTY………………………………………………………...21
WARRANTY REGISTRATION CARD …………………………………...…23
PARTS
MACHINE CONFIGURATIONS……………………………………………...25
SKID STEER HITCH ADAPTER ASSEMBLY - 10675…………………....26
TOP LINK CYLINDER – 10481…………………………………………..27-28
3-POINT ASSEMBLY – 11116……………………………………………….29
SKID STEER HITCH ASSEMBLY – 11117…………………………………30
SLIDING OFFSET ASSEMBLY………………………………………….31-33
SFI LEG ASSEMBLY – 11118…………………….…………………...........34
SFI FRAME ASSEMBLY – 11119…………………………………………...35
CENTERING SPRING ASSEMBLY – 11124……………………………….36
COULTER ASSEMBLY- 13245, 12346………………………………... 37-39
SFI ROLL HOLDER ASSEMBLY – 11120………………………………….40
SFI BLADE ASSEMBLY – 11121……………………………………………41
SAFETY
RECOGNIZE SAFETY INFORMATION
This is the safety alert symbol.
When you see this symbol on
your machine or in this manual,
be alert for the potential of
personal injury.
Follow the precautions and safe
operating practices highlighted by
this symbol.
A signal word - DANGER,
WARNING, or CAUTION - is used
with the safety alert symbol.
DANGER identifies the most
serious hazards.
On your machine, DANGER signs
are red in color, WARNING signs
are orange, and CAUTION signs
are yellow. DANGER and
WARNING signs are located near
specific hazards. General
precautions are on CAUTION
labels.
Follow Safety Instructions
Read the safety messages in this manual and on the machine. Follow these warnings
and instructions carefully. Review them frequently.
Be sure all operators of this machine understand every safety message. Replace
operator's manual and safety labels immediately if missing or damaged.
2
Wear Protective Equipment
Guard against injury from flying pieces
of debris; wear goggles or safety
glasses.
Wear close fitting clothing and safety
equipment appropriate to the job.
Prolonged exposure to loud noise can
cause impairment or loss of hearing.
Wear suitable hearing protection such
as earmuffs or earplugs to protect
against objectionable or uncomfortable
loud noises.
Inspect Machine
Inspect machine carefully each day by
walking around it before starting.
Keep all guards and shields in good
condition and properly installed. Fix
damage and replace worn or broken
parts immediately. Pay special
attention to hydraulic hoses and
electrical wiring.
Avoid High-Pressure Fluids
This machine uses a high-pressure
hydraulic system. Escaping fluid under
pressure can penetrate the skin
causing serious injury.
Never search for leaks with your
hands. Protect hands. Use a piece of
cardboard to find location of escaping
fluid. Stop engine and relieve pressure
before disconnecting lines or working
on hydraulic system.
3
If hydraulic fluid penetrates your
skin, see a doctor immediately.
Injected fluid must be removed
surgically within hours or gangrene
may result. Contact a knowledgeable
medical source or call 911.
Avoid Backover Accidents
Before moving machine, be sure all
persons or vehicles are clear of
machine path. Turn around and look
directly for best visibility. Keep
windows clean.
Be certain reverse warning alarm is
working properly (if equipped).
Use a signal person when backing if
view is obstructed or when in close
quarters. Keep signal person in view
at all times. Use prearranged hand
signals to communicate.
WARNING: Keep all people away
from the machine while operating. Do
not allow workers to walk near the
installer while putting fabric in the
ground.
4
Avoid Work Site Hazards
Avoid contact with gas lines, buried
cables and water lines. Call utility
line location services to identify all
underground utilities before starting
work.
Prepare work site properly. Avoid
operating near structures or objects
that could fall onto the machine. Clear
away debris that could move
unexpectedly if run over.
Avoid boom or attachment contact
with overhead obstacles or
overhead electrical lines. Never
move machine closer than 3 m (10 ft)
plus twice the line insulator length to
overhead wires.
Keep bystanders clear at all times.
Use barricades or a signal person to
keep vehicles and pedestrians away.
Use a signal person if moving machine
in congested areas or where visibility is
restricted. Always keep signal person
in view. Coordinate hand signals
before starting machine.
Operate only on solid footing with
strength sufficient to support machine.
Be especially alert working near
embankments or excavations.
Avoid working under over-hanging
embankments or stockpiles that
could collapse under or on machine.
5
SAFETY DECAL PLACEMENT
GENERAL INFORMATION
The diagrams on this page show the locations of the safety decals used on the Silt
Fence Installer. The decals are identied by their part numbers, with images of the
decals shown on the following pages. Use this information to order replacements for
lost or damaged decals. Be sure to read all decals before operating the Silt Fence
Installer. They contain information you need to know for both safety and longevity.
7137318
7137317 6583862
6815993
6815993
11187
7137317
7137319
6815993 6815993
6583862
6
6815993
6815993
11187
7137317
7105979
6815993
11187
7137317
11190
7105979
11187
6815993
IMPORTANT: Keep all safety signs clean and legible. Replace all missing, illegible, or
damaged safety signs. When replacing parts with safety signs attached, the safety signs
must also be replaced.
REPLACING SAFETY SIGNS: Clean the area of application with nonammable solvent,
then wash the same area with soap and water. Allow the surface to fully dry. Remove the
backing from the safety sign, exposing the adhesive surface. Apply safety sign to the position
shown in the diagram above and smooth out any bubbles.
7
be AWARe of sAfety sIGNs oN the mAchINe
68647 SW 7137317 enUS
Do not stand between tractor
and implement.
Keep bystanders away.
Install support stands before
disconnecting implement
from tractor.
CRUSHING CAN CAUSE
SERIOUS INJURY
OR DEATH
WARNING
DECAL - WARNING, HITCH CRUSH
PART # 7137317
WARNING: Stay clear of tractor or loader when
attaching to installer. Do not stand between installer
and loader or tractor. Make sure the installer is se-
curely mounted to the loader quick attach or tractor
3-point before engaging locking levers.
AVOID INJURY OR DEATH
68647 SW 7137318 enUS
STORAGE POSITION
LOCKED POSITION
Swing lock must be in locked position before transporting
and before adjusting side shift (if equipped).
WARNING
DECAL - WARNING, TRANSPORT LOCK
PART # 7137318
WARNING: Always lock installer in
the straight position before trans-
port. Move the latch to the storage
position before use to prevent dam-
age to the installer.
1-888-258-0808
68647 SW 6702301
PART # 7137319
DANGeR: Electricity or gas explosion can kill.
Locate utilities before installing silt fence.
DECAL - WARNING, BURIED UTILITIES
8
Table des matières
Autres manuels burchland Matériel agricole
Manuels Matériel agricole populaires d'autres marques
GSi
GSi PNEG-2314 Manuel utilisateur
Checchi & Magli
Checchi & Magli TEXDRIVE Manuel utilisateur
Amazone
Amazone Cenius 4003-2TX Manuel utilisateur
MASSEY FERGUSON
MASSEY FERGUSON MF 9313S Manuel utilisateur
Cima
Cima BLITZ Instructions d'utilisation et d'entretien
Amazone
Amazone CombiDisc 3000 Instructions d'installation
