Buderus GB142 Guide de l'utilisateur

GB142 Startup

•Remove the cover of the boiler and set the cover aside

•Shut the incoming gas cock off so that no gas is supplied to the unit

•On the GB142’s gas valve, located to the left of the Fan Assembly, find the inlet

tapping, and slacken brass flat head screw approximately 2 full turns.

•Hook up a manometer so that it is reading Positive Gas Pressure onto this

tapping and turn on the incoming gas

•Check the gas pressure, making sure that it falls within the appropriate range

3.5 to 10.5 inch W.C. Natural Gas and 8.0 to 13.0 inch W.C. LPG

•Turn on the gas valve.

•Power up the unit by turning on the On/Off switch On the BC10 control.

•Press and hold the “Chimney Sweep” button until a decimal point can be seen in

the bottom right of the display

•Once the decimal point is visible, press and hold both the Chimney Sweep and

the Service buttons at the same time until “L - -” is visible on the display. This

is telling you that the boiler is going to fire off and modulate to 100% of its

capability.

•Check the gas pressure with the manometer once the unit has reached High Fire.

Confirm that it does not drop below 3.5” W.C. If it does, check gas pipe sizing

per the relevant gas pipe sizing chart.

•Turn off of the boiler using the On/Off button on the BC10 boiler control.

•Shut off the external boiler gas valve, remove the manometer, and tighten the

slackened brass screw.

•To the right of the inlet tapping on the gas valve is the manifold tapping.

Slacken this screw and hook up the manometer so that it is reading Negative

Gas Pressure.

•Open the external gas valve

•Turn the boiler on again with the On/Off button found on the BC10

•Locate the “Service Button” and confirm the operating pressure of the heating

system is at minimum 15psi

•Cycle through back to the temperature readout on the BC10 by pressing the

Service Button again

•Press and hold the “Chimney Sweep” button until a decimal point can be seen in

the bottom right of the display

•Press the “Wrench” and “Chimney Sweep button at the same time until “L—“

appears on the display

•Press and hold the “Reset” button to lower the percentage to “L30” which is

indicating that it is firing at 30% of its Load.

•Check the air/gas ratio on the manometer. It should be -.04 – 0 inch W.C. ( +/-

.02 inch W.C.)

•If ratio is out of range, adjust it with the adjustment screw on the gas valve,

located just to the lower right of the manifold pressure port.

•Unscrew the brass plug found on the adjustment screw.

•Using a 4mm Alan key, adjust the ratio as necessary.

•Once in range, turn off the boiler, remove the manometer, tighten the screw,

and reinstall the brass plug on the adjustment screw.

•Put the cover back onto the boiler

•Unscrew the plug for the flue gas test ports on the two pipe flue adapter

•Insert your combustion analyzer’s adapter into the flue gas test port

•Insert your combustion analyzer’s probe into the adapter making sure to locate

it in the center of the exhaust pipe (This can be done by fully inserting it until it

hits the back of the pipe. Mark the spot on the outside of the adapter, and

remove the probe. This will give you a depth marking. Find the halfway spot on

the probe and reinsert into the flue only up to that mark).

•Power up the unit by turning on the On/Off switch

•Using the BC10 control, press and hold the “Chimney Sweep” button until a

decimal point can be seen in the bottom right of the display

•Once the decimal point is visible, press and hold both the Chimney Sweep and

the Service buttons at the same time until “L - -” is visible on the display.

•Once on High Fire, confirm that your CO2, O2, and CO content to ensure that

they are all within a .02 +/- range from the prescribed specifications. If the

range is not met, remove the cover and adjust as necessary. Check the venting

and air intake piping to confirm that they are installed according to Buderus’s

specifications.

•Press the Service Button until the temperature is visible on the BC10 display

•Once viewing the temperature, press and hold the “Chimney Sweep” button until

the decimal point is removed from the display.

Rev: 2018-04-04

Autres manuels pour GB142

Table des matières

Autres manuels Buderus Chaudière

Buderus

Buderus 600 - 11R Guide de l'utilisateur

Buderus

Buderus G201 Manuel utilisateur

Buderus

Buderus Logano G315 Guide rapide

Buderus

Buderus P 120/5W Manuel utilisateur

Buderus

Buderus Logano GB125 Manuel utilisateur

Buderus

Buderus GB312/200 Manuel utilisateur

Buderus

Buderus Logano G215 US Manuel utilisateur

Buderus

Buderus Logano plus GB312 Manuel utilisateur

Buderus

Buderus Logano G334 X Manuel utilisateur

Buderus

Buderus Logamax plus GB142-24 Manuel utilisateur

Buderus

Buderus Logano GE515 Manuel utilisateur

Buderus

Buderus Logano G334 X Manuel utilisateur

Buderus

Buderus Condensing gas boiler Manuel utilisateur

Buderus

Buderus Logano plus GB312 Instructions d'utilisation

Buderus

Buderus Logamax plus GB162-100 kW Mode d’emploi

Buderus

Buderus Logamax plus GB162-100 kW Manuel utilisateur

Buderus

Buderus 500 Series Manuel utilisateur

Buderus

Buderus Logano GA244 Manuel utilisateur

Buderus

Buderus SU120/5 Manuel utilisateur

Buderus

Buderus Logano G334 X Manuel utilisateur

Buderus

Buderus SU120/5 Mode d’emploi

Buderus

Buderus Logamax plus Manuel utilisateur

Buderus

Buderus 500-24S Manuel utilisateur

Buderus

Buderus Logano plus GB402 Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur

Radiant

Radiant R2K 55 Manuel