BroadMobi R800A Manuel utilisateur
R800A User Manual
Interface
key
Illustrate
Power key
Long press over 5 seconds to power on and long press to power off
WPS
Press to active the WPS
Reset
The Reset button is on the opposite side of the machine. If you forget
Administrator password or Wireless network key, you can press the
Reset key to restore factory default settings.
LED Indication
Indicator
Color
Working Status
Power
LED
Green
Solid: booting up the device
Amber
Blink: Charging
Blink:
Turn
on-0.5s
Turn
off-0.5s
Blue
Solid: Battery High(100%-60%) or Charge Completed
Amber
Solid: Battery Middle (60%-15%)
Red
Solid: Battery too low nearly shut down (<15%)
SMS LED
Blue
Blink: New SMS
Signal
LED
Blue
Blink: Register to LTE(not connect)
Solid: Connected to LTE network
Green
Blink: Register to 3G(not connect)
Solid: Connected to3G network
Purple
Blink: Register to2G(not connect)
Solid: Connected to2G network
Red
Blink: No Service/Device Error
WiFi LED
Blue
Solid: No Client
Blink: Client is actived
Blink: WPS is active
Blink:
Turn
on-0.2s
Turn
off-0.1s
Installation
Follow the diagram to install the SIM card and SD card
Tips: Always switch the device off and disconnect the charger before removing the
battery.
1. Remove the back cover and battery;
2. Insert the SIM card and SD card. Ensure that the contact area on the card is facing
down and that the beveled corner on the card is facing the beveled corner on the
holder.
3. Align the battery contacts with the battery compartment connectors, and insert
the battery. Replace the back cover lastly.
R800A Usage
R800A support 4G/3G/2G networks. Insert the SIM card, Wi-Fi devices and the
computer can access the Internet through R800A, enjoy high-speed network
services. Smart phones, tablet computers, game consoles and other Wi-Fi devices
can be connected with the R800AC Wi-Fi connection for Internet access.
Computers & laptops etc. may be connected to the R800A via USB cable for
Internet Access.
R800A computer for the first time via a USB connection, you need to follow the
prompts to install the driver
Wi-Fi wireless Internet access
In order for a Wi-Fi device to establish a connection with the R800A for the first
time, you will need to select the R800ASSID (Wi-Fi name) & enter the relevant Wi-Fi
password, which you may find in the following ways:
Method one: on the nameplate view the default SSID and Wi-Fi passwords
Method Two: Login management page view
1. Computer, open your browser, input http://192.168.0.1 and enter.
●The default Account is admin
●The default Password is admin
Enter the Account and Password, login administration pages
2. Enter the Wi-Fi menu, view the default SSID and Wi-Fi password. The default 2.4G
SSID is R800A_2.4G.The default 5G SSID is R800A_5G.The Wi-Fi password are both
1234567890.
★Recommend that you start using R800A administration pages after setting a
convenient landing memorizing SSID and a higher safety factor Wi-Fi
passwords
Install the driver and connecting the device
USB Connection: Windows 7 for example
1. Keep R800A powering on, Plug the device into your computer, it will shows like
the following pictures step by step.
2. Double-click the , wait for the installation to complete
3. Check the network card is installed correctly, like the following pictures
Or,
Establish Wi-Fi connection: you must ensure that the computer equipped with
a wireless network card. If the computer showed the presence of Wi-Fi
connectivity, the wireless LAN is available. Otherwise, you need to check your
wireless network card is working properly. (The following will be 2.4GWi-Fi as
an example)
1. In the Wi-Fi list, select the SSID consistent with R800A Wi-Fi, click Connect
2. Enter the correct Wi-Fi password, click OK
3. Wait a moment, Wi-Fi connection is displayed next to the name, Wi-Fi
connection is successful
4. Check the network card is installed correctly, like the following pictures
Table des matières
Autres manuels BroadMobi Routeur sans fil
