Brighter Eye 360 Led Manuel utilisateur

Eye 360 Led

LED WASH

This product manual contains important information about the

safe installation and use of this projector. Please read and follow

these instructions carefully and keep this manual in a safe place

User manual

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions........................................................................................................................................... 3

2. Installation....................................................................................................................................................... 4

3. Features & Specifications ................................................................................................................................ 5

5. Operating Instructions..................................................................................................................................... 6

7. DMX-512 Control Connections........................................................................................................................ 7

8. Menu ............................................................................................................................................................... 8

9. DMX Channels ................................................................................................................................................. 9

10. Maintenance and Cleaning.......................................................................................................................... 10

11. Troubleshooting .......................................................................................................................................... 11

STATEMENT

The product has full capability and intact packing when leaves factory. All the users should

comply with provided warnings and manual. Any damages caused by misuse are not

included in our guarantee. We cannot be responsible for any malfunctions & problems

owing to ignoring the manual.

1. Safety Instructions

•Please keep this User Guide for future consultation. If you sell the unit to another user, be

sure that they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire

hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but

always by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is

higher than this Unit surface temperature may reach up to 85℃.

•DO NOT touch the housing bare-hands during its operation. Turn off the power and allow

about 15 minutes for the unit to cool down before replacing or serving.

•In case of serious operating problem, stop using the unit immediately. Never try to repair

the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance centre. Always use

the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or

moisture.

•DO NOT open the unit within five minutes after switching off.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly

damaged.

Caution:

There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs by yourself. If your unit requires service, please contact your nearest dealer.

2. Installation

Take 1 hook and 1 safety cord out from the package and x the hook on the chassis, and fasten the

hook with the chassis to the underside of fixture with 2 screws, Hang the fixture on the structure

and fasten the screws attached to the hook. (See the WARNING on the underside of the base as

shown above) Always ensure that the projector is firmly anchored to avoid vibration and slipping

whilst functioning. Always ensure that the structure, that you are going to mount the projector on,

is secure and is strong enough to support a weight of each projector.

WARNING:

The projector MUST be lifted or carried by the HANDLES instead of clamps.

For safety the safety cord should afford 10 times of the unit’s weight.

3. Features & Specifications

VOLTAGES:

100V~240V AC，50/60Hz

POWER CONSUMPTION:

400W@220V

LED:

Power consumption: 12W(RGBW)

Quantity: 36pcs

Manufacturers Rated LED Lifespan: 50000 Hours

COLOURS:

RGBW linear color mixing

DIMMER:

0-100% linearly adjustable

STROBE:

Electronic Strobe 0 ~25F.P.S

PAN AND TILT:

PAN(0°~540°) and TILT(0°~270) , User-selectable Pan/Tilt ranges

ZOOM ANGLE:

10°~55°

CONTROL:

DMX512, 3 pins interfaces DMX Control Protocol

18 channels in standard mode, and 25 channels in extended mode, Master/Salve Synchronous

Control Mode:

DMX512 / Master-Slave / Auto

HOUSING:

Flame retardant engineering plastic shell/cast aluminum, Ip20

WORK ENVIRONMENT TEMPERATURE:

-10°C~40°C

CARTONS PACKING DIMENSION:

Inner: 460x335x385 (mm) Outer: 435x345x480 (mm)

WEIGHT:

Net weight :9.6Kgı Gross Weight: 13.0Kg

DIMENSIONS [mm]:

4. Operating Instructions

•The moving head is for spot effect for on-site decoration purpose.

•Don’t turn on the fixture if it’s been through severe temperature difference like after

transportation because it might damage the light due to the environment changes. So make

sure to operate the fixture until it is in normal temperature.

•This light should be keep away from strong shaking during any transportation or movement.

•Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.

•Don’t expose the fixture in overheat, moisture or environment with too much dust when

installing it. And don’t lay any power cables on the floor. Or it might cause electronics shock

to the people.

•Make sure the installation place is in good safety condition before installing the fixture.

•Make sure to put the safety chain and check whether the screws are screwed properly when

installing the fixture.

•Make sure the lens are in good condition. It’s recommended to replace the units if there are

any damages or severe scratch.

•Make sure the fixture is operated by qualified personnel who know the fixture before using.

•Keep the original packages if any second shipments is needed.

•Don’t try to change the fixtures without any instruction by the manufacturer or the

appointed repairing agencies.

•It is not in warranty range if there are any malfunctions from not following the user manual

to operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.

5. DMX-512 Control Connections

Connection between controller and projector and between one projector and another must be made

with a 2 core-screened cable, with each core having at least a 0.5mm diameter. Connection to and

from the projector is via cannon 3 pin XLR plugs and sockets. The XLR's are connected as shown in

the figure above.

Note: Ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The projector accepts digital control signals in protocol

DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to

the second fixture’s input and connect the rest fixtures in the same way. Eventually connect the last

fixture’s output to a DMX terminator as shown in the figure below.

TERMINATOR:

6. Menu

Setting DMX Start Address

Each projector must be given a DMX start address, so that, the correct projector responds to the

correct control signals. This DMX start address is the channel number from which the projector

starts to “listen” to the digital control information being sent out from the controller. The fixture

have 3 DMX modes. There are simple mode, standard mode and extended mode. For example

standard mode has 15 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address

016, No. 3 projector’s address 031, No. 4 projector’s address 046 and so on.

Launch the projector. Press button ENTER more than 5 seconds to unlock panel.

Press button ENTER to display DMX address.

Press button UP or DOWN , you can set the address.

Press button ENTER to confirm, which means the projector has saved the Start Address

automatically, when powered on next time, it will display the value saved last time.

Press button UP or DOWN to change values (add or subtract).

Press button FUNC, to return to the upper menu one by one.

Configuration:

Press button ENTER to unlock panel. Menu will be displayed on the screen. Each menu has its own

sub-menu. Each menu has specific function. Please refer to “Operation Menu” below for details.

Press button UP or DOWN if you want to browse or change through the various Setup Options.

Press button ENTER to save your settings or enter the next menu.

Press button UP or DOWN to change values.(Add or subtract)

Press button FUNC , it will return to the upper menu one by one.

7. DMX Channels

18 Mode chanel Function Instruction

1Pan 0-255

2Tilt 0-255

3Pan Fine 0-255 (16 bit)

4Tilt Fine 0-255 (16 bit)

5Motor Speed 0-255 From fast to slow

6Dimmer 0-255 (0-100% dimming)

7Shutter 0-255 Strobe Slow to fast (0 is open)

8Red 0-255 (linear)

9Green 0-255 (linear)

10 Blue 0-255 (linear)

11 White 0-255 (linear)

12 Chose Color 0-255 (build in color makro)

13 Ring Control

0-60: all rings work together

61-120: First Ring

121-180: Second Ring

181-255: Third Ring

14 Makro

0-10 No Makro

10< Makro ON

15 Makro Speed 0-255 From slow to fast

16 Zoom 0-255 Zoom range

17 XY Motor

0-64: no effect

64-128: X motor reverse

129-192: Y motor reverse

193-255: XY motor reverse

18 Reset

0-64: No effect

65-128: Auto mode

129-192: Sound mode

193-255: Reset

10. Maintenance and Cleaning

To prolong a Projector’s life, regular maintenance should be done for its LED optical system, to

ensure that the system is in its best operational condition. If the projector does not work properly,

check the fuses on the power socket of the projector, if it is burned, they should only be replaced

by fuses of the same specification. Should these be damaged, call a qualified technician before

replacement. The projector has thermal protection device that will switch off the projector in case

of overheating. Should this occur, check if the fans work normally or fan and fan shield are blocked

by dust.

Any maintenance work should only be carried out by qualified technicians.

25 Mode chanel Function Instruction

1Pan 0-255

2Tilt 0-255

3Pan Fine 0-255 (16 bit)

4Tilt Fine 0-255 (16 bit)

5Motor Speed 0-255 From fast to slow

6Dimmer 0-255 (0-100% dimming)

7Shutter 0-255 Strobe Slow to fast (0 is open)

8Red 0-255 (linear) Ring 1

9Green 0-255 (linear) Ring 1

10 Blue 0-255 (linear) Ring 1

11 White 0-255 (linear) Ring 1

12 Red 0-255 (linear) Ring 2

13 Green 0-255 (linear) Ring 2

14 Blue 0-255 (linear) Ring 2

15 White 0-255 (linear) Ring 2

16 Red 0-255 (linear) Ring 3

17 Green 0-255 (linear) Ring 3

18 Blue 0-255 (linear) Ring 3

19 White 0-255 (linear) Ring 3

20 Chose Color 0-255 (build in color makro)

21 Makro

0-10 No Makro

10< Makro ON

22 Makro Speed 0-255 From slow to fast

23 Zoom 0-255 Zoom range

24 XY Motor

0-64: no effect

64-128: X motor reverse

129-192: Y motor reverse

193-255: XY motor reverse

225 Reset

0-64: No effect

65-128: Auto mode

129-192: Sound mode

193-255: Reset

Table des matières

Autres manuels Brighter Luminaire

Brighter

Brighter Smart 1000 Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur