BRAYER BR4956 Manuel utilisateur
Instruction manual
Инструкция по эксплуатации
Fan BR4956
Вентилятор BR4956
brayer.ru
СОДЕРЖАНИЕ
EN......................................................................................................................................3
DE....................................................................................................................................12
RU ...................................................................................................................................22
KZ....................................................................................................................................32
3
EN
FAN BR4956
The fan is intended for articial ventilation of the
room.
DESCRIPTION
1. Base
2. Body
3. Outgoing Airow Grill
4. Control Panel/Display
5. Carrying Handle
6. Air-Inlet Grill
7. Power Cable
Control Panel/Display
8. 8. On/O button « »
9. 9. Power Indicator « »
10. Display Backlight and Operation Modes Indicator
On/O Button « »
11. Timer Indicator « »
12. Timer on/o button « »
13. Display
14. Room Temperature Indicator « »
15. Airow Speed Selection button « »
16. Oscillation Mode Indicator « »
17. Oscillation Mode On/O button « »
EN
Remote control
18. On/O button « »
19. Airow speed selection button « »
20. Timer On/O button « »
21. Battery Holder
22. Remote Control
23. Oscillation Mode On/O button « »
24. Display backlight on/o button « »
4
EN
°C
1
2
3
4 5
6
7
12 15
13
14
8
9
16
24 19
18
23 20
22
11
10 17
21
5
EN
Рiс. 1 Рiс. 2
Рiс. 3
6
EN
SAFETY MEASURES AND OPERATION
RECOMMENDATIONS
Read the operation manual carefully before using
the fan; after reading, keep it for future reference.
• Use the unit for its intended purpose only, as it is
stated in this manual.
• Mishandling the unit can lead to its breakage and
cause harm to the user or damage to the user’s
property, which is not covered by warranty.
• Do not use the power cord as a carrying handle for
the fan.
• Do not wind the power cord around the fan body.
• Provide that the power cord does not contact with hot
surfaces and sharp furniture edges.
• Protect the unit from impacts, falling, vibrations and
other mechanical stress.
• Avoid blocking the air inlet grid of the fan with foreign
objects, do not cover the unit during the operation.
• Do not use the unit in places where inammable
liquids are used or aerosols are sprayed, do not use
the unit in the places where such liquids are stored.
• Do not use the unit near heating appliances, heat
sources or open ame.
• Do not use the unit outdoors, in bathrooms or in
places with high humidity.
• Do not use the unit in proximity to the kitchen sink,
near swimming pools or other containers lled with
water.
• If the unit is dropped into water, unplug it
immediately, and only then you can take the unit out
of water. Apply to the authorized service center for
testing or repairing the unit.
• Do not touch the unit body, the power cord and the
power plug with wet hands.
• It is not recommended to use the unit during lightning
storms.
• Do not block the fan grids and do not insert foreign
objects onto them.
ATTENTION! A lithium battery is used in the remote
control. To avoid danger, do not allow children to play
with the battery. If your child swallowed a battery,
immediately see your doctor.
• Make sure that the operating voltage of the unit
indicated on the label corresponds to your home
mains voltage.
• Place the fan vertically on a at dry moisture- and
heat-resistant surface, do not place it horizontally and
do not turn it over.
• Do not place the fan on soft surfaces, such as
carpets with high pile, sofas or beds.
• Do not place the fan near curtains and do not direct it
to house plants.
• Do not use the fan in a limited space, for example, in
built-in cabinets or wall niches.
• It is not recommended to stay in the zone of the air
ow from the fan for a long period of time, especially
for children and the elderly.
7
EN
• Never leave the unit connected to the mains
unattended.
• Unplug the unit after usage or before cleaning.
• Switch the fan o and unplug the power cord plug
from the mains socket.
• When unplugging the unit, hold the power plug and
carefully remove it from the mains socket, do not pull
the power cord, as this can lead to its damage or
cause a short circuit.
• Do not immerse the unit into water or any other
liquids.
• If water droplets fall on the fan body, switch it o and
disconnect the power plug from the mains before
touching the unit, then wipe the fan body with a dry
cloth.
• For child safety reasons do not leave polyethylene
bags used as packaging unattended.
ATTENTION! Do not allow children to play with
polyethylene bags or packaging lm. Danger of
suocation!
• During the unit operation and breaks between
operation cycles, place the unit out of reach of
children.
• The device is not intended to be used by people
(including children) with physical, sensory,
psychological, or mental disabilities, or lacking
experience or knowledge, if they are not under the
supervision of or have not been instructed on the
usage of the device by the person responsible for
their safety.
• From time to time check the power cord integrity.
• If the power cord is damaged, it should be replaced
by the manufacturer, a maintenance service or
similar qualied personnel to avoid danger.
• Do not repair the unit by yourself. Do not
disassemble the unit by yourself, if any malfunction
is detected, and after the unit was dropped, unplug it
and apply to the service center.
• To avoid damages, transport the unit in the original
package.
• Keep the unit in a dry cool place out of reach of
children and disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, DO NOT USE THE UNIT FOR COMMERCIAL
OR LABORATORY PURPOSES.
• The unit is not intended for usage by children.
• Do not leave children unattended to prevent them
using the device as a toy.
• Do not allow children to touch the operating surface,
the unit body, the power cord or the power plug
during operation of the unit.
• Be especially careful if children or disabled persons
are near the operating unit.
8
EN
BEFORE THE FIRST USE
After the unit’s transportation or storage at negative
temperature, unpack it and wait for at least 3 hours
before using it.
• Unpack the unit and remove all the packaging
materials.
• Keep the original package.
• Read the safety measures and operating
recommendations.
• Check the delivery set.
• Examine the unit for damages, in case of damage do
not plug it into the mains.
• Make sure that specied specications of power
supply voltage of the unit correspond to the
specications of your mains.
• Wipe the fan body with a slightly damp cloth and then
wipe it dry.
ASSEMBLING THE FAN
• The fan is delivered with a disassembled base (1).
Do not switch the fan on without the base (1).
• Use a crosshead or at tip screwdriver (not supplied)
to assemble the base (1).
• Position the fan body (2) horizontally.
• Assemble the Base (1): join the two halves of the
Base (1) (g. 1) and secure them using 4 screws.
• Using the 4 screws, attach the Base (1) to the lower
part of the body (2) (g. 2).
• Place the fan vertically on the base (1).
Remote control (23)
ATTENTION! A lithium battery is used in the remote
control. To avoid danger, do not allow children to
play with the battery. If your child has swallowed
a battery, immediately see a doctor. Battery
installation/replacing (pic. 3)
• Press on the clamp and remove the battery holder
(21) from the remote
• control (22) body, insert a CR2025 battery (supplied
with the unit) into the holder, strictly following the
polarity.
• Install the battery holder (21) into the remote control
(22).
Notes:
- if there is an isolation insert in the battery holder
(21), remove the insert;
- replace the battery in time;
- do not recharge the lithium battery;
- remove the battery if you are not planning to use
the unit for a long time;
- remove the used battery from the remote control
(22) and dispose of it.
• When you use the remote control, direct it to the front
part of the fan body (2).
• The distance between the remote control and the fan
should not exceed 5 m, the coverage angle should
be up to 30 degrees.
9
EN
• Avoid exposing the receiver to direct sunlight,
otherwise false activation of control commands is
possible.
USING THE FAN
• Use the handle (5) to carry the fan.
• Place the fan base (1) on a at, dry and steady
surface.
• Do not place the fanon soft surfaces, such as carpets
with high pile, sofas or beds.
• Insert the Power Cable (7) plug into the mains, you
will hear a sound signal, the Power Indicator (9) «
» and the Room Temperature Indicator (14) «
» will turn on, and numeric indication of the room
temperature will appear on the Display (13).
Switching the fan on/o and selecting the airow
speed
Notes:
- the buttons on the control panel (4) are sensory,
you just need to touch the button to switch the
necessary operation mode on;
- each pressing of buttons on the control panel (4)
or on the remote control (22) is accompanied with
a sound signal;
- if no buttons have been pressed, in 10 minutes
the Display (13) backlight will turn o, as well as
the Room Temperature Indicator (14) « », the
Current Mode Indicators (11 or 16), and the Power
Indicator (9) « ».
• To turn the fan on, press the « » button (8) on the
Control Panel (4) or the « » button (18) on the
Remote Control (22), you will hear a sound signal and
the fan will turn on at the medium airow speed (13);
the digital «2» symbol will turn on.
• After a while the numeric indication of the room
temperature will appear on the Display (13).
Note: the temperature digital indications (18) may
be slightly dierent from the readings of another
thermometer.
• Pressing the button (15) « » on the control panel (4)
or the button (19) « » on the remote control (22) you
can select the airow speed, the symbols «1-2-3» will
appear on the display (13).
• To turn on the fan, press the « » button (8) on the
Control Panel (4) and the « » button (18) on the
Remote Control (22), the fan will turn on, the (9) « »
and (14) « » indicators will turn on and the numeric
indication of the room temperature will appear on the
Display (13).
Fan operation time timer
• To set the operating time of the fan, press the « »
button (12) on the Control Panel (4) or the « » button
(20) on the Remote Control (22) button you will hear
a sound signal, the « » indicator (11) will turn on, and
10
EN
the Timer operation time will appear on the Display
(13) as ickering numeric symbols «00».
• Press again the buttons (12 or 20) to set the timer
operation time. Timer operation time can be set from
1 hour to 12 hours with 1 hour setting step.
• To turn o the Timer press the button (12 or 20)
repeatedly until the Display (13) shows numeric
indication with the value of «00».
Switching the fan body oscillation on/o
• To turn the oscillation mode on, press the «
» button (17) on the Control Panel (4) or the «
» button (23) on the Remote Control (22), the «
» indicator (16) will turn on, to turn o the oscillation
mode, press the « » button (17) on the Control
Panel (4) or the « » button (23) on the Remote
Control (22), the « » indicator (16) will turn o.
The display backlight on/o button
• To turn o the Display backlight, press the «
» button (10) on the Control Panel (4) or the « »
button (24) on the Remote Control (22), the Display
(13) and Indicators (9, 11, 14, 16) backlight will turn
o. To turn the Display (13) and the operation modes
indicators backlight o, press the « » button (10) on
the Control Panel (4) or the « » button (24) on the
Remote Control (22), the Display (13) and indicators
backlight will turn on.
Note: if no actions are taken for 10 minutes, the Display
(13) and the operation modes indicators will turn o
automatically.
• To turn o the fan, press the « » button (8) on the
Control Panel (4) or the « » button (18) on the
Remote Control (22) and remove the Power Cable
(7) plug from the mains.
CLEANING AND MAINTENANCE
• Before cleaning the fan, switch it o (7) and unplug it.
• Wipe the fan body with a slightly damp cloth and then
wipe it dry.
• Do not use liquid detergents, abrasive cleaners and
any solvents to clean the fan (2).
• To avoid the risk of electric shock provide that no
water or other liquid gets into the fan body.
• You can use a vacuum cleaner with an appropriate
attachment to clean the Air-Inlet Grill (6) and the
Outgoing Airow Grill (3).
STORAGE
• After cleaning put the fan away for storage in a dry
cool place away from children and disabled persons.
• Before using the fan next time, it is recommended to
check the unit operability and integrity of the power
cord isolation and the power cord plug.
Table des matières
Langues :
Autres manuels BRAYER Ventilateur
BRAYER
BRAYER BR4961WH Manuel utilisateur
BRAYER
BRAYER BR4958BK Manuel utilisateur
BRAYER
BRAYER BR4951 Manuel utilisateur
BRAYER
BRAYER BR4953 Manuel utilisateur
BRAYER
BRAYER BR4961BK Manuel utilisateur
BRAYER
BRAYER BR4974 Manuel utilisateur
BRAYER
BRAYER BR4975 Manuel utilisateur
BRAYER
BRAYER BR4960 Manuel utilisateur
BRAYER
BRAYER BR4954 Manuel utilisateur
BRAYER
BRAYER BR4971 Manuel utilisateur
