Braeburn Builder 1000NC Manuel utilisateur

This thermostat requires 24 Volt AC Power or two (2) properly installed

“AA” Alkaline batteries for proper operation. When connecting 24 Volt

AC Power the batteries may be installed as a backup.

For use only as described in this manual. Any other use

will void warranty.

1000NC

Single Stage Heat / Cool

Conventional and Heat Pump

Speciﬁcations

About Your Thermostat

Installation

System Testing

Setting User Options

Operating Your Thermostat

Additional Operation Features

Thermostat Maintenance

Warning

Turn off power to the heating or cooling

equipment before installation.

Attention

For installation by experienced service

technicians only.

Follow applicable codes.

1200NC

Up to 2 Heat / 1 Cool

Conventional and Heat Pump

Read all instructions before proceeding.

This thermostat is compatible with:

  • Singlestageheat/coolconventionalandheatpumpsystems

  • Conventionalsystemsupto2heat/1cool(1200NConly)

  • Singlecompressorheatpumpsystemswithanauxiliaryheatstage(1200NConly)

  • 250–750millivoltheatonlysystems

Electrical and control speciﬁcations:

 •ElectricalRating:24VoltAC

  •1ampmaximumloadperterminal

  •ACPower:18–30VoltsAC

  •DCPower:3.0VoltDC(2“AA”AlkalineBatteriesIncluded)

  •ControlRange:45°–90°F(7°–32°C)

  •TemperatureAccuracy:+/-1°F(+/-.5°C)

Terminations

  •1000NC–Rc,Rh,O,B,Y,W,G,C

  •1200NC–R,O,B,Y1,E/W1,G,W2,C

Speciﬁcations

1000NCW-100-12

Non-Programmable

Thermostats

Model number is located on back of thermostat

Detailed

User Guide

Setting User Options

Operating Your Thermostat

Additional Operation Features

Thermostat Maintenance

For installation by experienced service

technicians only.

Follow applicable codes.

About Your Thermostat

Installation

Warning

Disconnect power before beginning installation.

Thermostat Location

Installthethermostatapproximately4-5feet(1.5m)abovetheoorinan

areathathasagoodamountofaircirculationandmaintainsanaverage

roomtemperature.

Avoidinstallationinlocationswherethethermostatcanbeaffectedby

drafts,deadairspots,hotorcoldairducts,sunlight,appliances,concealed

pipes,chimneysandoutsidewalls.

Room Temperature...........Displaysthecurrentroomtemperature

Arrow Buttons..................Usedtoincreaseordecreasesettings

System Switch..................SelectsHeat,CoolorOff

Backlight Button..............Illuminatesthedisplaybacklight

Low Battery Indicator......Indicateswhenthebatteriesneedto

  bereplaced

System Status Indicator...Displaysinformationaboutthestatusof

   thesystem

Reset Button.....................

Resetsthermostatbacktofactorydefaults

Fan Switch........................Selectsthesystemfanmode

Battery Compartment.......Locatedinthebackofthethermostat

Install your new Braeburn thermostat in 5 basic steps:

1 InstalltheSub-Base

2 ProvidePower

3 ConnectYourWires

4 SetInstallerSwitches

5 AttachThermostattoSub-Base

Install the Sub-Base:

•Removethesub-basefromthebodyofthethermostat.

•Mountthesub-baseasshownbelow:

Drill 3/16” pilot holes in

your desired location.

Use supplied anchors for

drywall or plaster.

Provide Power

•For 24 Volt AC power,youmustconnectthecommonsideofthetrans-

 formertotheCterminalonthethermostatsub-base.

•For primary or back-up power,insertthe2supplied“AA”type

 alkalinebatteriesintothebatterycompartmentlocatedinthefrontof

 thethermostat,nearthebottom.MakesuretopositionthePositive

 (+)andNegative(-)sides

ofthebatteriescorrectlywiththe+/-symbols

 inthebatterycompartment.

24VAC Power

Terminal (C)

Terminal Function Description

 Rc*   Input 24VoltACCoolingTransformer

       (DualTransformerSystemsOnly)

 Rh*   Input PowerConnection(24VoltACHeating

       TransformerorMillivoltPowerSource)

 O   Output ReversingValve(CoolActive)

 B   Output ReversingValve(HeatActive)

 Y   Output

1stStageCompressor(appearsas Y1on1200NC)

 G   Output FanControl

 W   Output 1stStageConventionalHeat

 C   Input 24VoltACTransformerCommon

Connect Your Wires

Wiring Terminations

Terminal Function Description

 W1/E   Output (W1)1stStageConventionalHeat

(E)EmergencyHeatRelay

 W2   Output 2ndStageHeat/AuxiliaryHeat

Additional Terminations (1200NC only)

Heat Only or Millivolt

Set Installer Switch to NORM

Rh*

 PowerConnection

W HeatRelay(appearsasW1/Eon1200NC)

G FanRelay[note 4]

C 24VoltACTransformerCommon[note 1]

1 HEAT / 1 COOL Single or Dual Transformer

Set Installer Switch to NORM

Rh*

24VoltACPower(heatingtransformer)[note 2]

Rc*

24VoltACPower(coolingtransformer)[note 2]

W HeatRelay(appearsasW1/Eon1200NC)

Y CompressorRelay(appearsasY1on1200NC)

G FanRelay

C 24VoltACTransformerCommon[note 1, 3]

Typical Wiring Conﬁgurations

NOTE: The “Installer Switch” option will be conﬁgured in the next step.

Conventional Systems

*AppearsasRon1200NC(singletransformer)

NOTES - Conventional Systems

[1]Ifbatteriesareinstalledthe24VoltACcommonconnectionisoptional

[2]Removefactoryinstalledjumperfordualtransformersystems

[3]Indualtransformersystems,transformercommonmustcomefrom

 coolingtransformer

[4]Ifneededforsystem

Provide disconnect and overload protection as required.

2 HEAT / 1 COOL Single Transformer (1200NC Only)

Set System Type to NORM

24VoltACPower

W1 HeatRelayStage1

W2 HeatRelayStage2

Y1 CompressorRelayStage1

G FanRelay

C 24VoltACTransformerCommon[note 1]

Conventional Systems (cont.)

Typical Wiring Conﬁgurations

NOTE: The “Installer Switch” option will be conﬁgured in the next step.

Heat Pump Systems

1 HEAT / 1 COOL - No Auxiliary Heat

Set Installer Switch to HP

Rh* 24VoltACPower

Rc* ConnectedtoRhwithsuppliedJumperWire

O or B

 ChangeoverValve [note 2]

CompressorRelay(appearsasY1on1200NC)

G FanRelay

C 24VoltACTransformerCommon [note 1]

2 HEAT / 1 COOL - Including Auxiliary Heat (1200NC only)

Set Installer Switch to HP

R 24VoltACPower

O or B

 ChangeoverValve[note 2]

CompressorRelay(1ststageheating/cooling)

W2 AuxiliaryHeatRelay(2ndstageheating)[note 3]

W1/E EmergencyHeatRelay [note 3]

G FanRelay

C 24VoltACTransformerCommon [note1]

(Continued)

*AppearsasRon1200NC(singletransformer)

Factory Setting

Switch Default Options Comments

Heat Pump Systems (cont.)

NOTES - Heat Pump Systems

[1]Ifbatteriesareinstalledthe24VoltACcommonconnectionisoptional.

[2]SelectOforcoolactiveor Bforheatactive.

[3]InstallaeldsuppliedjumperbetweentheW2 and Eterminalsif

 thereisnoseparateemergencyheatrelayinstalled.

Provide disconnect and overload protection as required.

NORM/HPNORM

 F/C F

 HE/HG HG

Set Installer Switches

NORM Selectforconventionalsystems

 HP Selectforheatpumpsystems

 F Selectforfahrenheittemperaturescale

 C Selectforcelsiustemperaturescale

 HG Selectforgasheat

 HE Selectforelectricheat

Attach Thermostat to Sub-Base

1.Lineupthethermostatbodywiththesub-base.

2.Carefullypushthethermostatbodyagainstthesub-baseuntilitsnaps

 intoplace.

NOTE: The reset button should be pressed after making any changes to the

installer switches.

NOTE: The thermostat

hinges from the top

and latches at

the bottom.

System Testing

Warning

Read Before Testing

• Donotshort(orjumper)acrossterminalsonthegasvalveoratthe

 heatingorcoolingsystemcontrolboardtotestthethermostatinstalla-

 tion.Thiscoulddamagethethermostatandvoidthewarranty.

• DonotselecttheCOOLmodeofoperationiftheoutsidetemperature

 isbelow50ºF(10ºC).Thiscouldpossiblydamagethecontrolledcool-

 ingsystemandmaycausepersonalinjury.

• Thisthermostatincludesanautomaticcompressorprotectionfeatureto

 avoidpotentialdamagetothecompressorfromshortcycling.When

 testingthesystem,makesuretotakethisdelayintoaccount.

NOTE: The compressor delay can be bypassed by pressing the reset button

on the front of the thermostat. All user settings will be returned to factory

default.

1 MovetheSYSTEMswitchtoHEATmode.

2 Presstoraisethesettemperatureaminimumof3degreesabove

thecurrentroomtemperature.Thesystemshouldstartwithinafew

 seconds.Withagasheatingsystem,thefanmaynotstartrightaway.

3 MovetheSYSTEMswitchtotheOFFmode.Allowtheheatingsystemto

 fullyshutdown.

4 MovetheSYSTEMswitchtotheCOOLmode.

5 Presstolowerthesettemperatureaminimumof3degreesbelow

thecurrentroomtemperature.Thesystemshouldstartwithinafew

 seconds(unlesscompressorshortcycleprotectionisactive–See

 noteabove).

6 MovetheSYSTEMswitchtotheOFFmode.Allowthecoolingsystemto

 fullyshutdown.

7 MovetheFANswitchtotheONmode.Thesystemfanshouldstart

 withinafewseconds.

8 MovetheFANswitchtotheAUTOmode.Allowthesystemfanto

 turnoff.

Setting User Options

Advanced User Options

Useroptionsallowyoutocustomizesomeofyourthermostatsfeatures.

Mostuserswillnotneedtomakeanychangestothesettingsin

thissection.

To access the User Options menu, hold down both the and buttons

for approximately 3 seconds until the screen changes and displays

the ﬁrst User Option.

PresstheorbuttontochangethesettingforthedisplayedUserOption.

Afteryouhavemadeyourdesiredsetting,pressandtogetherto

advancetothenextUserOption.

Thethermostatwillreturntonormalmodeafteryourlastuseroptionis

madeorafternokeyshavebeenpressedfor5seconds.

User Factory Setting

No. Options Default Options Comments

 1 1ststage

0.5

0.5, 1.0

Selecta1ststagetemperature

   differential  

or 2.0 differentialof0.5˚,1.0˚or2.0˚F

       (0.2˚,0.5˚or1.0˚C)

 2 2ndstage

2.0

1.0, 2.0,

 Selecta2ndstagetemperature

   differential  

3.0, 4.0

, differentialof2˚,3˚,4˚,5˚or6˚F

(1200NCOnly

)

5.0

6.0

 (1.0˚,1.5˚,2.0˚,2.5˚or3.0˚C)

Table of User Options

Detailed Explanation of User Options:

Temperature Differential

(User Option 1 and 2)

Thedifferentialsettingisthetemperaturecontrolrangethatyourthermostat

willprovide.Thesmallerthesetting,thetighteryourrangeoftemperature

controlandcomfortwillbe.The2ndstagedifferentialisonlyforsystems

withasecondstageofheating(auxiliaryheat).

Operating Your Thermostat

Setting the System Control Mode

TheSystemControlhasseveralmodesofoperationthatcanbeselectedby

movingtheSYSTEMswitchtooneofthreepositions.

COOL Onlyyourcoolingsystemwilloperate

OFF Heatingandcoolingsystemsareoff.

HEAT Onlyyourheatingsystemwilloperate.

Additional Switch Position (Model 1200NC Only):

EMER Operatesabackupheatsource(EmergencyHeat)forheatpump

 systemsonly.

NOTE:

If your model 1200NC was set to a

con-

ventional system (NORM) then you will not have the

EMER (emergency heat) option and “NO AUX SET”

will ﬂash in the display if EMER is selected

with the

system switch.

Setting the Fan Control Mode

The Fan Control has 2 modes of operation – AUTO

and ON. The mode can be selected by moving the

FAN switch to the appropriate position.

AUTO Thesystemfanwillrunonlywhenyour

  heatingorcoolingsystemisrunning.

ON Thesystemfanwillstayon.

Detailed Explanation of User Options:

Temperature Differential

(User Option 1 and 2)

Thedifferentialsettingisthetemperaturecontrolrangethatyourthermostat

willprovide.Thesmallerthesetting,thetighteryourrangeoftemperature

controlandcomfortwillbe.The2ndstagedifferentialisonlyforsystems

withasecondstageofheating(auxiliaryheat).

Temperature Adjustment

Presstheorbuttontoadjustthecurrentsetpointtemperature.

Status Indicators

Statusindicatorsappearinthedisplaytoletyou

knowifyoursystemisheating,coolingoroff.

HEAT

Ifashing,indicatesyourheatingsystem

  isrunning.

COOL

Ifashing, indicatesyourcoolingsystem

  isrunning.

Additional Status Indicators (Model 1200NC Only):

AUX Indicatesthattheauxiliarystageofheatingisrunning

  (Multi-StageSystemsonly),orthattheemergencyheat

  systemisrunning(heatpumpsystemsonly).

Resetting the Thermostat

Thisthermostatprovidesyouwitharesetbuttonthatwilleraseallofyour

usersettings.

Toresetthethermostat,useasmallobjectsuchasatoothpickorpaper-

clipandgentlypressthebuttonlocatedinsidethesmallholeonthefrontof

thethermostathousinglabeled“reset”.

Additional Operation Features

Compressor Protection

Thisthermostatincludesanautomaticcompressorprotectiondelayto

avoidpotentialdamagetoyoursystemfromshortcycling.Thisfeature

activatesashortdelayafterturningoffthesystemcompressor.

Thermostat Maintenance

Changing the Batteries

Dependingonyourparticularinstallation,this

thermostatmaybeequippedwithtwo(2)“AA”

typealkalinebatteries.

If batteries are installed and they become low,

a low battery indicator will appear in the display.

You

shouldchangeyourbatteriesimmediately

whenyouseethelowbatterysignalbyfollowing

theseinstructions.

1.Openthebatterydoorlocatedonthe

 bottomofthethermostat.

2.Removeoldbatteriesandreplace

 withnewbatteries.

3.Makesuretocorrectlypositionthe

 (+)and(-)symbols.

4.Closethebatterydoor.

Thermostat Cleaning

Neversprayanyliquiddirectlyonthethermostat.Usingasoftdampcloth

wipetheouterbodyofthethermostat.Neveruseanyabrasivecleansersto

cleanyourthermostat.

For troubleshooting tips, visit braeburnonline.com.

BraeburnSystemsLLC

2215CornellAvenue•Montgomery,IL60538

TechnicalAssistance:www.braeburnonline.com

Callustoll-free:866-268-5599(U.S.)

630-844-1968(OutsidetheU.S.)

Store this manual for future reference.

1000NCW-100-12

Limited Warranty

Wheninstalledbyaprofessionalcontractor,thisproductisbackedbya5year

limitedwarranty.Limitationsapply.Forlimitations,termsandconditions,you

mayobtainafullcopyofthiswarranty:

·Visitusonline:www.braeburnonline.com/warranty

·Phoneus:866.268.5599

·Writeus:BraeburnSystemsLLC

2215CornellAvenue

Montgomery,IL60538

NOTE: We recommend replacing the

thermostat batteries annually or if the

thermostat will be unattended for an

extended period of time.

Autres manuels pour Builder 1000NC

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Braeburn Thermostat

Braeburn

Braeburn 2010 Manuel utilisateur

Braeburn

Braeburn Builder Series Manuel utilisateur

Braeburn

Braeburn 3220 Manuel utilisateur

Braeburn

Braeburn 5020 Instructions d'utilisation

Braeburn

Braeburn 229100 Manuel utilisateur

Braeburn

Braeburn 7300 Manuel utilisateur

Braeburn

Braeburn 2020NC Instructions d'utilisation

Braeburn

Braeburn 7300 Manuel utilisateur

Braeburn

Braeburn 6100 Instructions de montage

Braeburn

Braeburn 5200 Manuel utilisateur

Braeburn

Braeburn Premier 5400 Manuel utilisateur

Braeburn

Braeburn 2020NC Manuel d'utilisation et d'entretien

Braeburn

Braeburn 165 Manuel utilisateur

Braeburn

Braeburn 5300 Instructions de montage

Braeburn

Braeburn 2020 Manuel d'utilisation et d'entretien

Braeburn

Braeburn 1020NC Manuel utilisateur

Braeburn

Braeburn 1020 Instructions d'utilisation

Braeburn

Braeburn Premier Series Instructions de montage

Braeburn

Braeburn Premier 5400 Instructions de montage

Braeburn

Braeburn 3020 Instructions d'utilisation

Braeburn

Braeburn Premier 3100 Manuel utilisateur

Braeburn

Braeburn Builder 2200 Manuel utilisateur

Braeburn

Braeburn 5020 Instructions d'utilisation

Braeburn

Braeburn Premier 5300 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur