Bradley Express SS Series Manuel utilisateur

IMPORTANT

Read this entire installation manual

to ensure proper installation, then

file the manual with the owner or

maintenance department.

Flush all the water supply lines

before making connections.

Wall anchors used must have a

minimum pull-out rating of 1,000

lbs.

Product warranties may be found

under "Product Information" on

our web site at

www.bradleycorp.com.

P.O. Box 309, Menomonee Falls, WI 53052-0309

TEL. 1-800-BRADLEY FAX 262-251-5817

http://www.bradleycorp.com

Table of Contents

Pre-Installation Information . . . . . . . . . . . . . . . .2

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4

Installation Instructions . . . . . . . . . . . . . . . . 5-10

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . .10

Cleaning and Maintenance . . . . . . . . . . . . . . . .11

Soap Dispenser Maintenance . . . . . . . . . . . .2-13

Assembly of Components . . . . . . . . . . . . . . .3-14

Check Valve Troublshooting . . . . . . . . . . . . . .15

Solenoid Valve Troubleshooting . . . . . . . . . .5-16

Vernatherm™ Mixing Valve . . . . . . . . . . . . . . .17

SS-3/AZ/WH97TAS

Express® Lavatory

System SS-Series

Complies with Texas Accessibility

Standards (TAS) for Juvenile Height

applications.

215-1175 Rev. H; EN 08-805

Page 1 of 17 4/24/08

Installation

Instructions

OBSOLETE

Express® Lavatory System SS-Series

SS-3/AZ/WH97TAS Installation - Obsolete

2 4/24/08 Bradley Corporation • 215-1175 Rev. H; EN 08-805

Pre-Installation Information

Texas Accessibility Standards compliant:

The SS-3/AZ/WH97TAS Express® Lavatory System meets Texas Accessibility (TAS) requirements

for barrier-free clearances, reaches and controls. Always check local codes and ordinances for

compliance.

Infrared sensor and solenoid

Each sprayhead is controlled by a separate sensor and solenoid valve, enabling each user to activate a

single flow of water. Each valve uses less than half the maximum of hot water allowed by the

ANSI/ASHRAE/IES 90A-1980 Standard.

Supplies required for installation:

• (10) 3/8" wall anchors, bolts and washers to mount frame and bowl to wall

(minimum pull-out rating of 1,000 lbs.)

• 1/2" NPT tempered supply piping

• 1-1/2" NPT drain piping

• 110 volt electrical outlet for 110/24 VAC plug-in transformer

(supplied)

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AZ/WH97TAS

3Bradley Corporation • 215-1175 Rev. H; EN 08-805 4/24/08

SS-3/AZ/WH97TAS Express® Lavatory System Dimensions

Express® Lavatory System SS-Series

SS-3/AZ/WH97TAS Installation - Obsolete

4 4/24/08 Bradley Corporation • 215-1175 Rev. H; EN 08-805

Dimensions continued . . .

Juvenile Height

SS-3/AZ/WH97TAS

Grades 6 thru 8 or 9

Juvenile Height

SS-3/AZ/WH97TAS

Grades Pre-K thru 5 or 6

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AZ/WH97TAS

5Bradley Corporation • 215-1175 Rev. H; EN 08-805 4/24/08

Installation Instructions

Step 1: Rough in

Note: See Figure 1 (below), and Figures 1A and 2 (on page 6) when roughing in the Express®.

IMPORTANT: Flush the supply lines before making connections. Debris in supply

lines will cause the valves to malfunction.

IMPORTANT: Dimensions shown in Figure 1 are for Juvenile Height (grades Pre-K

thru 5 or 6) and in Figure 1A for Juvenile Height (grades 6 thru 8 or 9)

IMPORTANT: Turn OFF electrical power to the outlet when installing the Express®.

1. Rough in 1/2" NPT hot and cold supply lines through wall at dimensions shown below.

2. Rough in 1-1/2" NPT drain waste connection through wall at dimensions shown below.

3. Install the 110 volt GFCI electrical outlet per local code at the location shown in Figure 2 on page 6.

4. Install (10) 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer)

at the locations shown in Figure 1 and 1a on pages 5- 6.

NOTE: The anchors will be used to mount the Express® bowl and frame to the wall.

Step 1: Rough-in continues...

Figure 1

Juvenile Height SS-3/AZ/WH97TAS Express® Lavatory System

(grades Pre-K thru 5 or 6)

Express® Lavatory System SS-Series

SS-3/AZ/WH97TAS Installation - Obsolete

6 4/24/08 Bradley Corporation • 215-1175 Rev. H; EN 08-805

Figure 2

Figure 1a

Juvenile Height SS-3/AZ/WH97TAS Express® Lavatory System

(grades 6 thru 8 or 9)

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AZ/WH97TAS

7Bradley Corporation • 215-1175 Rev. H; EN 08-805 4/24/08

Installation Instructions continued . . .

Step 2: Mount frame to wall

1. Remove the nine Torx-head screws securing the panel to the frame and remove the panel (see

Figure 3).

2. Position the frame against the wall, ensuring that it is level.

IMPORTANT: Anchoring the frame to a wall that is not flat may cause the frame to

bend. If necessary, install shims to compensate for wall distortion.

3. Ensure that the back of the frame is flat against the wall. If wall is not flat, insert shims behind

the frame to ensure that it will not bend when anchored.

4. Once you have positioned the frame such that it is level and flat against the wall or shimmed, use

the 3/8" bolts and washers to mount the frame to the wall (see Figure 4).

Installation Instructions continue...

Figure 4

Figure 3

(9) TORX-HEAD

SCREW

FRAME

PANEL

(10) 3/8" BOLTS

AND WASHERS

FRAME

Express® Lavatory System SS-Series

SS-3/AZ/WH97TAS Installation - Obsolete

8 4/24/08 Bradley Corporation • 215-1175 Rev. H; EN 08-805

Installation Instructions continued . . .

Step 3: Install bowl assembly

IMPORTANT: Moving and positioning the bowl will require more than one person.

Note: Refer to Figure 5 below when installing the bowl assembly.

1. With someone to assist you, place the bowl assembly squarely onto the frame.

2. Attach the front of the bowl assembly to the frame using the four 1/4"-20 x 3/8" pan-head

screws and washers provided. Do not tighten screws at this time.

IMPORTANT: When bolting the bowl assembly to the frame and wall, do not overtight-

en the bolts. Overtightening bolts can damage the Terreon® material.

3. After the bowl assembly is attached to the frame, use two 3/8" bolts and washers (supplied by

the installer) to bolt the bowl to the wall anchors.

4. Tighten the screws installed in procedure #2 above to secure the bowl assembly to the frame.

Do not overtighten.

Installation Instructions continue...

Figure 5

BACK VIEW

Express® Lavatory System SS-Series

Installation - Obsolete SS-3/AZ/WH97TAS

9Bradley Corporation • 215-1175 Rev. H; EN 08-805 4/24/08

Installation Instructions continued . . .

Step 4: Connecting supply, drain, and electrical

1. FOR HOT AND COLD SUPPLIES: Connect the flexible hoses installed to the Vernatherm™

Mixing Valve to the hot and cold water supply piping from the wall (see Figure 6a).

Note: The red marking on Vernatherm™ Mixing Valve indicates hot water supply inlet.

FOR SINGLE TEMPERED SUPPLY: Attach the stop/strainer/check valve to the 1/2" tempered

supply line. Attach the 3/8" tube from the sprayhead to the 90° elbow located on the

stop/check/strainer (see Figure 6b).

2. Insert the plastic tubing from the bowl assembly into the Vernatherm™ Mixing Valve.

3. Assemble the P-trap (supplied) and make drain connections.

IMPORTANT: The Express® must be connected to the 24 VAC Class II plug-in

transformer provided. Connection to 110 VAC can result in damage

to the electronics and cause personal injury.

4. Plug in the 24 VAC Class II transformer (supplied) into the 110 volt electrical outlet.

STOP/STRAINER/CHECK

VALVE

ELBOW 90°,

3/8" TUBE

ELBOW

Figure 6b

Figure 6a

PLASTIC

TUBING VERNATHERM™

THERMOSTATIC

MIXING VALVE

FLEXIBLE

SUPPLY

HOSE

CONNECT

TO 1/2"

NPT COLD

WATER

SUPPLY

CONNECT

TO 1/2" NPT

HOT WATER

SUPPLY

3/8" FEMALE

CONNECTOR

FLEXIBLE

SUPPLY

HOSE

Express® Lavatory System SS-Series

SS-3/AZ/WH97TAS Installation - Obsolete

10 4/24/08 Bradley Corporation • 215-1175 Rev. H; EN 08-805

Wiring Diagram

Installation Instructions continued . . .

Step 5: Completing installation

1. Turn on the water supply to the Express® and check for leaks.

2. Turn on the electrical power to the electrical outlet and pass your hand in front of each station’s

sensor until all the air is purged from the lines and water is flowing smoothly.

3. After testing is complete, reinstall panel to frame. Fasten panel with the ten Torx-head screws

provided (see Figure 3 on page 7).

4. START-UP NOTE: This unit is equipped with adaptive infrared control. It may take up to eight

minutes to properly adjust to the environment when power is turned on or if power is interrupted

for more than fifteen seconds.

Note: For Express® units with optional soap dispensers, see pages 12-13 for soap dispenser

maintenance instructions.

Autres manuels pour Express SS Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bradley Appareil de salle de bains

Bradley

Bradley Verge LVLD Series Manuel utilisateur

Bradley

Bradley WS-1X-HN Manuel utilisateur

Bradley

Bradley S19-120 Manuel utilisateur

Bradley

Bradley S19345HXB Manuel utilisateur

Bradley

Bradley Express SS Series Manuel utilisateur

Bradley

Bradley S19-300T Manuel utilisateur

Bradley

Bradley HN300 Manuel utilisateur

Bradley

Bradley E19-130 Manuel utilisateur

Bradley

Bradley S19-310UU Manuel utilisateur

Bradley

Bradley WF2608 Manuel utilisateur

Bradley

Bradley Verge LVSD2 Manuel utilisateur

Bradley

Bradley Express SS Series Manuel utilisateur

Bradley

Bradley Verge LVLD Series Manuel utilisateur

Bradley

Bradley Express MG Series Manuel utilisateur

Bradley

Bradley SA70 Series Manuel utilisateur

Bradley

Bradley CBSHWR9000KD Manuel utilisateur

Bradley

Bradley S19-315FPBF Manuel utilisateur

Bradley

Bradley Verge LVS Series Manuel utilisateur

Bradley

Bradley LVA Series Manuel utilisateur

Bradley

Bradley S19-130SS Manuel utilisateur

Bradley

Bradley Terreon Deep Bowl TDB3100 Series Manuel utilisateur

Bradley

Bradley Aerada 1200 Series Manuel utilisateur

Bradley

Bradley OmniDeck 3000 Series Manuel utilisateur

Bradley

Bradley Verge LVRD Series Manuel utilisateur

Manuels Appareil de salle de bains populaires d'autres marques

DURAVIT

DURAVIT C.1 C15240 0090 Manuel

Heatstore

Heatstore HSTRL500WTN Manuel utilisateur

Sunshower

Sunshower PURE SOLO Manuel utilisateur

Delabie

Delabie Delabie Sporting 714700 Manuel utilisateur

Kohler

Kohler K-13056 Instructions de montage

ESS

ESS Container TCL-11 Manuel utilisateur

Mustee

Mustee 22C Manuel utilisateur

VITRA

VITRA V-Flow Manuel utilisateur

baliv

baliv DUK-80.30 T Manuel utilisateur

Malmet

Malmet B105BT Manuel utilisateur

bathstore

bathstore Transition H1690MM Mode d’emploi

BELLOSTA

BELLOSTA Edward 0800/M Manuel utilisateur

baliv

baliv DU-5160 Manuel utilisateur

Franke

Franke PRTR0006 Manuel utilisateur

Gessi

Gessi RILIEVO 59011 Manuel utilisateur

noken

noken VITAE 100188525-N299998810 Manuel utilisateur

Allen + Roth

Allen + Roth 1142VA-30-201 Manuel utilisateur

Britex

Britex HBDA Manuel utilisateur