Boss Audio Systems BV7332B Manuel utilisateur

CONTENTS

Safety Precautions.................................................................2-3

Installation.............................................................................4-6

Wiring Connections...................................................................7

Basic Operation........................................................................8

RadioOperation.........................................................................9

DVD/VCD/CD/MP3/WMA Operation..................................10-14

BluetoothOperation.................................................................15

Other Operation.......................................................................16

Maintenance...........................................................................17

IR Remote Control...................................................................18

Troubleshooting Guide...........................................................19

SAFETY PRECAUTIONS

Important Warnings to Take Note of BEFORE Starting

the Installation

Damage Caused By Incorrect Installation or Usage is

NOT Covered By Warranty.

PLEASE Take the Time to Read the Installation Notes

Carefully.

Please make all necessary connections and terminate

any unused wires so they do not short. If you feel

uncomfortable preforming the install consult a profes-

sional installer.

To avoid any possible damage to your vehicles electrical system, be

sure to disconnect the battery cable before beginning installation.

The unit is intended for vehicles with a 12-volt battery and negative grounding.

Before installing the unit in a recreational vehicle, truck, or bus, check that the

battery voltage is 12 volts.

Remove the two transport screws from the top of the unit before instal-

lation.

Be sure to connect the negative (-) speaker leads to the negative (-) speaker

terminal. Never connect the negative (-) speaker leads to chassis ground.

This unit is only designed for use with 4 speakers. Do not combine outputs

for use with 2 speakers. Do not ground negative speaker leads to the chassis

ground.

Speakers connected to this unit must be high-power units with a minimum rat-

ing of 45W and impedance of 4 to 8 ohms. Connecting speakers with output

and/or impedance values other than those noted there will result in damage

to the head unit and the speakers.

Check the condition off your speakers carefully - connecting the unit to

old of degraded speakers may result in a fault which will damage the

audio IC and invalidate the warranty.

If this unit is installed in a vehicle that does not have an ACC (accessory)

position on the ignition switch, the red lead of the unit should be connected to

a terminal coupled with ignition switch ON/OFF operations. If this is not done,

the vehicle battery may be drained when you are away from the vehicle for

several hours.

Secure the wiring with zip ties or electrical tape. . To protect the wiring, wrap

adhesive tape around them where they lie against metal parts. To avoid

short-circuiting, cover all disconnected lead with insulating tape. There is a

possibility of short-circuiting if the leads are not insulated.

Route and secure all wiring so it cannot touch any moving parts, such as the

gear lever and handbrake. Do not route wiring in places that get hot, such as

near the heater outlet. If the insulation of the wiring melts or gets torn, there is

a danger of the wiring short circuiting to the vehicle’s body.

Don’t pass the yellow lead through a hole into the engine compartment to

connect to the battery. This will damage the lead’s insulation and cause a very

dangerous short.

Do not shorten any leads, if you do, the protection circuit may fail to work

when it should.

Never feed power to other equipment by cutting the insulation of the power

supply lead of the unit and tapping into the lead. The current capacity of the

lead will be exceeded, causing overheating.

Since a unique audio I/C circuit is employed, never wire so the speaker leads

are directly grounded or the left and right - speaker leads are common.

When this product’s source is switched ON, a control signal is turned on

through the Blue/White lead. Connect to an external power amp’s system

remote control or the car’s Auto-antenna relay control terminal (max. 300mA

12V DC).

Do not block any vents or heater panels, Blocking them will cause heat to build

up and may result in fire.

When replacing the fuse(s) the replacement must be of the same amperage

as shown on the fuse holder. Never replace a fuse with another of a different

value. If the fuse blows again please contact your instsallation company.

Double check that all wiring and connections are correct before re-connecting

the battery and turning on the unit.

After completing the installation and before operating the unit, reconnect the

battery, then press the (RES) button with a pointed object, such as a ball-point

pen to set to unit to it’s initial status. After pushing the button, wait a few sec-

onds for the red light to flash.

SAFETY PRECAUTIONS

Remove the Old Unit from the Dashboard

DIN Front Mount

DO NOT DISCONNECT WIRES

AT THIS TIME!

2. Insert the keys supplied with the

old unit into both sides of the unit

as shown in figure below until

they click. Pull to remove the old

unit from the dashboard.

1. Remove the outer trim frame.

INSTALLATION

Tools for Installation

2 removal wrenches are supplied for taking out the old unit and place with this

brand name car radio. The following tools and supplies may also be needed for

the installation:

Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper

/Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill

Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for

Power Connections /14-16 Gauge Speaker Wires

The above are not supplied.

Before you install

Automotive audio equipment installations can be challenging even to the most

experienced of installation technicians. We strongly recommend that this unit

should be professionally installed by a VAT registered installer (this is a require-

ment to validate the warranty).

IMPORTANT: Remove the two transport screws from the top fo the unit before

installing.

Mark Polarity of the Speaker Wires

Marking the polarity of the speaker wirers will make it easier to connect the

existing speakers to your car radio. Consult wiring diagram of existing head unit

before disconnecting any wires. If you are not positive of the polarity of the exist-

ing wires from the speakers to the head unit, install new wires.

1. While the old unit is playing, disconnect the wires from one speaker.

2. Take a length of masking tape and fold it around the wire so it forms a flag.

3. On the masking tape mark the polarity of the speaker wires (+&-), as well as

left or right, and front or rear.

4. Double check that you marked the first speaker correctly by checking that the

speaker wires are the same at the head unit.

5. Repeat this procedure for all of the speakers.

6. Mark the power, ground, and any other wires also.

INSTALLATION

1. After removing the old radio

and mounting sleeve, insert sup-

plied mounting sleeve into open-

ing.

2. Bend the tabs on the mount-

ing sleeve to keep the mount-

ing sleeve firmly in place.

3. Attach wires from the unit to

existing wires. See wiring con-

nections diagram. Insert radio

into dashboard. Then apply the

trim frame to outside of radio.

4. Support radio using rear mounting

bolt and steel bar. (not included)

DIN Front Mount

WARNING!

Disconnect negative battery terminal from battery before starting

installation.

NOTE: Mark the polarity of the existing speaker wires before discon-

necting battery.

NOTE: Remove the two transport screws from the top of the unit

before installing.

NOTE: Outer trim frame, hook, and mounting sleeve are not used

for this installation

This is only intended as a general guide; contact the vehicle’s manufacturer for

specific instructions.

This menthod of installation uses the screw holes at the sides of the unit and

the holes of the existing vehicle mounting bracket.

1. Remove the hooks on both sides.

2. Aligh the screw holes of the mounting bracket supplied with the car and the

screw holes of the main unit. Tighten the 2 screws on each side of the unit.

Then fasten the brackets to the car.

3. Attach wires of the unit to existing speaker wires. See wiring diagram.

DIN Rear Mount

INSTALLATION

WIRING DIAGRAM

Make sure You have a good chassis ground. Good ground connection will

eliminate most electrical noise problems. A good chassis ground requires a

tight connection to the vehicle’s metal chassis. The area around the ground

connection should be clean, bare metal without rust, paint, plastic, dust, or dirt

for a good ground connection.

Black Ground

Connect to vehicle body/chassis. Make sure you have a good chassis ground.

This will eliminate most electrical noise form the motor and alternator. A good

chassis ground requires a tight connection to ground. The area should be free

from rust, paint or any form of dirt.

Yellow Memory Backup

Connect to electrical terminal always supplied with power regardless of ignition

switch position.

Orange Remote

Connect to Auto-antenna or power amp control wire/remote connection.

Maximum current 500mA.

Speaker Wiring Notes:

Follow the above wiring diagram to install the head unit with new or existing

speakers.

1. This unit is designed for use with four (4) speakers with impedance between

4 Ohms to 8 Ohms.

2. An Impedance load of less than 4 Ohms could damage the unit.

3. Never bridge or combine the speaker wire outputs. When not using four

speakers, use electrical tape to tape the ends of the unused speaker outputs to

prevent a short circuit.

4. Never ground the negative speaker terminals to chassis ground.

Connector A

1. Rear right speaker(+)/Purple

3. Front right speaker(+)/Grey

5. Front left speaker(+)/White

Rear right speaker(-)/Purple-Black

4. Front right speaker(-)/Grey-Black

6. Front left speaker(-)/White-Black

7. Rear left speaker(+)/Green

8. Rear left speaker(-)/Green-Black

Connector B

1. -

2. -

3. -

4. Battery 12V (+)/Yellow

5.Remote Trigger/Blue-White

6. -

7.ACC+/Red

8. Ground/Black

Basic Operation

1. Turning the unit on/off

Press the PWR button to turn the unit on. When the unit is on, press the PWR button once

to turn the TFToff. Press this button again to turn the TFT back on. Press and hold the PWR

button to turn the unit off.

2. Mode Selection

Press the MODE button to cycle the play mode between RADIO, USB, SD and AUX in.

Alternatively, press the MENU button and rotate the volume knob to select across different

play modes.

3. Sound Control

A. Volume

Use the VOL +/- Button to adjust the volume level. Turn the button clockwise to increase

the volume, and vice versa. The larger the number of volume, the higher the volume level.

B. Bass

Press the SELButton until the display shows “BAS”. Use the VOL +/- Button to adjust. When

EQ is ON, bass control is not available.

C. Treble

Press SELButton until the display shows “TRE”. Use the VOL+/- Button to adjust. When EQ

is ON, treble control is not available.

D. Balance

Press SEL Button until the display shows “BAL”, then use the VOL +/- Button to adjust the

balance between the left & right speakers.

E. Fader

Press SEL Button until the display shows “FAD”, then use the VOL +/- Button to adjust the

balance between the front & rear speakers.

F. Preset Equalizer Function – Press the MENU button and rotate the knob to enter SETUP.

Select AUDIO and then EQ and then the type of EQ.

G. Beep on/off

Press the MENU button and rotate the knob to enter SETUP. Select GENERAL and then

BEEP and then on or off.

H. MBP Bass/Loudness/EQ/Subwoofer

Press the MENU button and rotate the knob to enter SETUP. SelectAUDIO and then choose

the corresponding items to turn on or off.

4. Video Settings

Press the MENU button and rotate the knob to enter SETUP. Select VIDEO and then choose

between Brightness, Contrast, Saturation, Hue to adjust.

5. Clock Settings

Press the MENU button and rotate the knob to enter SETUP. Select CLOCK and then you

can set the time and clock display format.

6. APS/ button

In USB/SD/Disc modes, during music or video playback press the APS/ button once to

go back to the directory page, in which you can choose the desired file by pressing and

turning the volume knob, press again theAPS/ button to go back to the audio/video/image

selected page.

Radio Operation

1. Choose Radio Band

Press the MOD Button to access the radio function. Then press the BAND but-

ton to choose among the five radio bands - three FM Bands (FM1, FM2, and

FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up

to six preset stations, for a total of 30 preset memory stations.

2. Radio Tune/Seek Function

In radio mode, press the |<< or >>| button to automatically seek the next strong

and clear radio station. Press and hold the Seek +/- button until the screen

shows MANU SEEK. At this time, you can manually fine tune your desired

frequency. Wait until the MANU SEEK to disappear in order to perform auto

seek again.

3. Automatic Store/Preset Scan

A. Automatic Scan & Store

While listening to the FM Radio, press and hold the APS Button for 3 seconds.

The receiver will automatically scan and save stations for all the 3 FM Bands,

whichever band (FM1, 2 or 3) you are listening to.

While listening to the AM Radio, press and the APS Button for 3 seconds. The

receiver will automatically scan and save stations for the 2 AM Bands, whichev-

er band (AM1 or 2) you are listening to.

B. Scan Saved Stations

Press the APS button or the AMS button on the remote control once to perform

the scanning functions. In FM mode, press the APS button or the AMS button

and the stations in that FM band will be scanned; press the button in AM mode

and scan the band stations of that AM Band.

4. Save your Preset Stations

After choosing the preset stations in the list, you can adjust the frequency (by

|<< or >>| ), and save it by pressing and holding the volume knob. Alternatively,

you can choose the preset station in the list after adjustment, then save it by

pressing and holding the volume knob. The newly saved preset station will be

refreshed and it will show the new radio frequency.

5. LIST button

In radio mode, press the LIST button to go to the preset stations list. You can

select the stations by turning and pressing the volume knob. Press and hold

this button to go to the other radio function list include RDS function and st/

mo, loc/dx.

6. Mono/Stereo Reception Control

Press and hold LIST button after choosing ST in the list, you can turn ST on

or off to select stereo or mono reception. Improvement of reception of weak

stations can be done by selecting ST OFF operation which may cut down some

reception noise.

7. Local/Distance Reception Control

Press and hold LIST button after choosing LOC in the list, you can turn LOC on

or off to select local or distance reception. Improvement of reception of distant

stations can be done by selecting LOC OFF operation.

8 Radio Regions Setting

Press the MENU button and rotate the knob to enter SETUP. Select RADIO and then you

can set the radio system/region and turn on or off RDS Control.

Table des matières

Autres manuels Boss Audio Systems Récepteur de voiture

Boss Audio Systems

Boss Audio Systems 637UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 738BI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV7280 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9976B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems MP3-3O8OR Manuel utilisateur

Boss Audio Systems

Boss Audio Systems MR508UABW Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BVCP9800W Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV2950TU Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV3550 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 775DI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems AVA-916B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9978T Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9980NV Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9348B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 824UAB Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 758DBI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CD-3500R Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9759BD Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV7200 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9965I Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9564BI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV8970 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems MR1200 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV7265B Manuel utilisateur

Manuels Récepteur de voiture populaires d'autres marques

Motorola

Motorola VWA63 Manuel utilisateur

Nextar

Nextar D3201 Manuel utilisateur

Alpine

Alpine CDE-163BT Manuel utilisateur

Pioneer

Pioneer DEH-P645R Manuel utilisateur

Axxera

Axxera XDMA7600 Mode d'emploi

XM OnyX Manuel utilisateur

Sound Storm

Sound Storm STM93R Manuel utilisateur

Soundstream

Soundstream VIR-5000 Manuel utilisateur

Avson

Avson MKT Platform Manuel utilisateur

Sony

Sony MEX-1HD - Audio Library System Manuel utilisateur

Pioneer

Pioneer DVH-P500UB Manuel utilisateur

JVC

JVC KD-AHD69 Manuel utilisateur

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manuel utilisateur

Sony

Sony CDX-4160 - Cd Receiver Manuel utilisateur

XFIRE AUDIO

XFIRE AUDIO BMW42S Manuel utilisateur

VDO

VDO CD 2253 Manuel utilisateur

Volvo

Volvo 13 84 580 Manuel utilisateur

ZENEC

ZENEC ZE-160DVD Manuel utilisateur