Boss Audio Systems 624B Manuel utilisateur

DSP

LOC

LOUD

DSP

LOC

LOUD

CAR RADIO RECEIVER / MP3 PLAYER

WITH BULETOOTH HAND FREE SYSTEM

INSTRUCTION MANUAL

LOUD

BUTTON

AUDIO

BUTTON

INFO

BUTTON

BAND

BUTTON

LCD

DISPLAY

PLAY/

PAUSE

BUTTON

INTRO

SCAN

BUTTON

REPEAT

BUTTON

RANDOM

BUTTON

ENCODER

VOLUME

KNOB

MUTE

BUTTON

POWER

BUTTON

PRESET MEMORY STATION BUTTONS

(M1-M6)

AMS

BUTTON

TUNING /

SEEK

UP/DOWN

NEXT/BACK

BUTTON

TALK

BUTTON

CANCEL/

SRC

BUTTON

INFRARED

REMOTE

SENSOR

10+/- FOLDER

UP / DOWN

BUTTONS

E - 1

INSTALLATION

Before final installation, connect the wiring temporarily and make sure it is all working

properly.

Use only the parts included with the unit to ensure proper installation. The use of

unauthorized parts can cause malfunctions.

This item must be installed by an authorized dealer in order to keep the warranty vaild.

Install the unit where it does not get in the driver's way and cannot injure the passenger if

there is a sudden stop, like an emergency stop.

If installation angle exceeds 30 degrees, the unit might not give its optimum performance.

Avoid installing the unit where it would be subject to high temperature, such as direct

sunlight, or hot air, heater or where it would be subject to dust dirt or excessive vibration.

Be sure to remove the front panel before installing the unit.

DIN FRONT/REAR-MOUNT

This unit can be property installed either from Front (conventional DIN Front-mount) or Rear

(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis).

For details, refer to the following illustrated installation methods A and B.

- DIN FRONT-MOUNT (Method A)

Installation the unit

1. Dashboard

2. Holder

After inserting the half sleeve into the

dashboard, select the appropriate tab

according to the thickness of the

dashboard material and bend them

inwards to secure the holder in place.

182

a. Frame

b. Insert fingers into the groove in the

front of frame and pull out to remove

the frame. (When re-attaching the

frame, point the side with a groove

down wards and attach it.)

c. Insert the levers supplied with the

unit into the grooves at both sides of

the unit as shown in figure until they

click. Pulling the levers makes it

possible to remove the unit from the

dashboard.

Removing the unit

- DIN REAR-MOUNT (METHOD B)

Installation using the screw holes on the sides of the unit.

Fastening the unit to the factory radio mounting bracket.

1. Select a position where the screw

holes of the bracket and the screw

holes of the main unit become

aligned (are fitted) and tighten the

screws at 2 places on each side.

2. Screw

3. Factory radio mounting bracket.

4. Dashboard or Console

5. Hook (Remove this part)

Note: the mounting box, outer trim ring,

and half-sleeve are not used for method

B installation.

E - 2

2. DETACHABLE CONTROL PANEL (D.C.P.)

Removing The Detachable Control Panel (D.C.P.).

1. Turn the power off

2. Press the D.C.P. release button

3. Remove the D.C.P.

PANEL RELEASE

BUTTON

Attaching the DCP

CAUTION

1. Attach the panel at the right side first, with

point B on the main unit touching point A on

the D.C.P. (As shown on the diagram).

2. Then press the left side of D.C.P. onto the

main unit until a click sound is heard.

DO NOT insert the D.C.P from the left side. Doing so may damage it.

The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case

and be careful not to drop it or subject it to strong shocks.

When the release button is pressed and the D.C.P is unlocked, the car's vibrations may

cause it to fall. To prevent damage to the D.C.P, always store it in a protective case after

detaching it.

The rear connector that connects the main unit and the D.C.P is an extremely important

part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

Socket

Note:

If the D.C.P is dirty, wipe off the dirt with soft, dry cloth

only. And use a cotton swab soaked in isopropyl

alcohol to clean the socket on the back of the D.C.P.

DETACHABLE CONTROL PANEL (D.C.P.)

Removing The Detachable Control Panel (D.C.P.).

CAUTION

DO NOT insert the D.C.P from the left side. Doing so may damage it.

The D.C.P can easily be damaged by shocks. After removing it, place it in a protective case and

be careful not to drop it or subject it to strong shocks.

When the release button is pressed and the D.C.P is unlocked, the car's vibrations may cause it

to fall. To prevent damage to the D.C.P, always store it in a protective case after detaching it.

The rear connector that connects the main unit and the D.C.P is an extremely important part. Be

careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc.

Attaching the Detachable Control panel (D.C.P.)

1. Insert the right side of the D.C.P. Into

the main unit.

NOTE: The D.C.P. Must be attached into

the T-Joint.

2. Press the D.C.P. On to the left side of

middle of D.C.P. Until a click sound is

heard.

RELEASE

BUTTON

D.C.P.

PUSH

Note:

If the D.C.P is dirty, wipe off the dirt with soft,

dry cloth only. And use a cotton swab soaked

in isopropyl alcohol to clean the socket on the

back of the D.C.P.

Socket

1. Turn the Power off.

2. Press the Panel Release Button.

3. Remove the D.C.P.

E - 3

E - 4

ELECTRICAL CONNECTION

a. Make sure your car battery is a 12 volt (6 filler caps) negative ground system (if not, a

converter will be necessary).

b. Before starting wiring connections, disconnect the power supply by removing the fuse

from the fuse box.

c. Connect the power wire to one of the extra terminals of the fuse box.

d. Connect the black ground wire to a metal part of the car. It is important to make good

contact.

e. Make other wiring connections as shown.

f. If your car does not have ISO connector, you can procure it from any car accessory shop.

Notes: INCORRECT WIRING OR OPERATION WILL AVOID THE WARRANTY OF THIS UNIT.

(CAR UNIT BACK SIDE) FUSE

Fuse Replacement:

To replace the fuse, pull out the blown fuse

from the socket. Insert a new one with same

rating

GENERAL OPERATION

POWER ON/OFF BUTTON ( )

Press POWER button or any other button on the front of the radio to turn the unit on.

Press POWER button again to turn the unit off.

MUTE BUTTON

Press the mute button momentarily to mute the audio volume, and "Mute" will in the

display. Press the mute button again to restore volume to the previous setting.

AUDIO SELECT BUTTON

Press this button to select desired audio function.

VOLUME (VOL)->BASS (BAS)-> TREBLE (TRE)-> BALANCE (BAL)-> FADER (FAD)

Rotate Volume Control to adjust desired level within 3 seconds.

MENU BUTTON

Press MENU Button to navigate through the menu items, while the desired menu item is

displayed, use Volume control to adjust the selected function:

- LOC/ DX MODE

Use this mode to change between Local and Distant (DX) tuning mode. Local mode

improves reception in some areas where the signal is too strong.

Under clock display mode.press MENU button until the LCD flashes.

Rotate the volume knob in clockwise direction to adjust hour, other direction to adjust minute.

- CLOCK ADJUST

BEEP OFF: disable audible beep tone when any function is accessed.

BEEP ON: enable audible beep tone.

- BEEP MODE (BEEP ON / OFF)

EQ BUTTON (PRESET EQUALIZER)

SRC BUTTON

Press this button to select different sources , sequence as follow:

SOURCES PRIORITY

A) Tuner mode (Radio)

B) USB (only if a USB drive is inserted)

C) SD / MMC (only if a SD or MMC card is inserted))

D) AUX IN

E) BT MODE (only if unit is paired to a mobile phone)

Whenever a USB or SD/MMC is being inserted, unit will automatically switch to USB or

SD/MMC mode, does not matter the unit is currently in what mode.

When in USB or SD / MMC mode, if the USB or SD / MMC is being removed, unit will

automatically switch to radio mode.

FRONT AUX INPUT

INFO BUTTON

At Radio mode Press this button to view frequency of the station in listening and clock time .

At DSP off mode preset equalizer will be controlled by Bass / Treble setting.

ENCODER VOLUME KNOB

When the Menu function is not activated, rotate this knob to change the volume level.

When Menu function is activated, rotate this knob to navigate through different menu items.

Connect the external signal to the front 3.5mm earphone jack on front panel, then press

Mode button to select Aux mode. Press Mode button again to cancel Aux Mode and return

to previous mode.

DSP OFF->CLASSIC->POP->ROCK

E - 5

LOUDNESS BUTTON

Use this LOUDNESS control to increase bass output.

Press this button to search for radio stations.

BAND BUTTON

The RESET button is located on the front panel (as shown on the diagram). To press it vertically

with a ballpoint pen or metal object will activate it. The reset button is to be activated for the

following reasons:

RESET BUTTON

LIQUID CRYSTAL DISPLAY PANEL (LCD)

The LCD panel display the frequency, time and activated functions.

NOTE:

It is a characteristic of LCD panel that if subjected to cold temperatures for an extended period

of time, they will take longer time to illuminate than under normal conditions, in addition, the

visibility of the numbers on the LCD may slightly decrease. The LCD read-out will return to

normal when temperatures increase to a normal range.

STATION PRESET BUTTONS (M1-M6)

You can store & recall six preset radio stations by pressing M1-M6 buttons

TO STORE A STATION: 1) select a band (if needed)

2) select a station by tuning up / down button

3) hold a preset button which you want store the station for at least 2

seconds. The preset number will appear on the display

accompanied by a beeps sound.

TO RECALL A STATION: 1) select a band (if needed)

2) press a preset button briefly to recall the stored station.

Initial installation of the unit when all wiring is completed.

All the function buttons do not operate.

Error symbol on the display.

Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in

isopropyl alcohol to clean the socket on the back of the control panel.

E - 6

TUNING UP / DOWN BUTTON ( )

Press this button to change between bands FM1,FM2,FM3, MW1,MW2(AM).

AUTO MEMORY STORE/PRESET SCAN BUTTON (AMS)

1.PRESET SCAN: Press AMS button briefly enter Preset Scan mode, it will scan all the preset

stations in the memories, you can hear that will stay on each station for about 10 seconds.

2.AUTO MEMORY STORE: Press AMS button long to enter Auto Store mode, this feature will

automatically scan the current band and enter up to 6 strongest stations into the 6 preset

memories. To stop Auto Store & Scan, press the AMS button again.

E - 7

M1)PLAY/PAUSE AND FIRST TRACK BUTTON

M4)RANDOM PLAY BUTTON

INTRO SCAN BUTTON

TRACK UP AND TRACK DOWN BUT TON ( )

When random play mode is selected, the tracks will be played in random order, press this key

one more time to cancel random play mode.

Press this button to select Intro Scan function, the first 10 seconds of each track will be played

sequentially until this button is pressed again, then normal play will resume at the current track.

Under normal play mode, press the Track Up Button for less than 1 second to skip the

playback to the next track, or press the Track Down Button for less than 1 seconds to return to

the beginning of the current track, press this button one more time to skip to the previous

track.

When any of these buttons is pressed for more than 1 second, the Mp3 player will enter

Cue/Review mode, this is indicated by the flashing track number on the LCD. When the key is

released, normal play will resume.

Press this button briefly to pause MP3 play, press again to release pause.

M3)REPEAT BUTTON

Pressing this button will activate Repeat Function in the following order :

Repeat On Repeat Off

M2)

MP3/SD/USB OPERATIONS

MMC/SD CARD & USB DEVICE OPERATIONS

START THE USB DEVICE MODE

1.The USB socket is accessible as indicated in picture

1.(P.1)

2.Plug in the USB drive / device completely as indicated

in picture 2(P.2) and display will show USB-LOAD to

indicate that the USB drive / device is being plugged in

correctly & the download has begun.

3.Does not matter which source the unit is in

(TUNER,SD/MMC,AUX,BT,etc), once a USB drive / device

is being plugged into the unit, unit will automatically

switch to USB mode.

4.All the USB files playback function is same as normal

MP3 files playback.

1.Always unplugged the USB gently from the unit,

excessive force used will cause permanent & serious

damage to the unit & the USB drive / device.

TO STOP USB PLAYBACK

1.If the USB drive / device is unplugged, the unit will automatically switch to radio mode.

Or user can use SRC button to switch to other mode.

2.User can use the SRC button to choose USB mode (only if USB drive / device is

inserted in the unit ) or any other modes, when they are in any mode.

CAUTION

COMPATIBILITY

Due to the fast changing technology world, this unit may or

may not be compatible to all the USB drive / device

available with all the future technology, especially those

USB drive / device which require to install a driver. Always

choose a compatible USB drive / device which is

compatible with this unit.

Warning: Excessive weight or size USB drive/device

may cause permanent & serious damage to the unit and

may cause access to the buttons on the front panel

impossible. User must use an extension cable (provide

by USB device manufacturer) to connect with USB

socket to prevent any damage cause.

USB SPECIFICATION

* SUPPORT MAX 32G USB FLASH MEMORY

* SUPPORT MAX 9999 SONGS

* USB 1.1 DEVICE SUPPORT

* USB 2.0 DEVICE SUPPORT

(TRANSFER SPEED SAME AS VER 1.1)

* FILE MANAGER: FAT12/FAT16/FAT32

* CURRENT SUPPLY: MAX 500mA

NOTE:

This unit is not compatible with portable Hard-Disc.

E - 8

Table des matières

Autres manuels Boss Audio Systems Récepteur de voiture

Boss Audio Systems

Boss Audio Systems BV8975B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 3195 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 738BI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 637UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 648UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 820UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 506CA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9372BI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 758DBI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems AVA-2825R Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV8967B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV7464B Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9997BI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems CD-3075R Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9980NV Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV9371BD Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 625UAB Manuel utilisateur

Boss Audio Systems

Boss Audio Systems MR1306UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 0791489116046 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 658UA Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 835UI Manuel utilisateur

Boss Audio Systems

Boss Audio Systems BV7942 Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 616UAB Manuel utilisateur

Boss Audio Systems

Boss Audio Systems 611UAB Manuel utilisateur

Manuels Récepteur de voiture populaires d'autres marques

Motorola

Motorola VWA63 Manuel utilisateur

Nextar

Nextar D3201 Manuel utilisateur

Alpine

Alpine CDE-163BT Manuel utilisateur

Pioneer

Pioneer DEH-P645R Manuel utilisateur

Axxera

Axxera XDMA7600 Mode d'emploi

XM OnyX Manuel utilisateur

Sound Storm

Sound Storm STM93R Manuel utilisateur

Soundstream

Soundstream VIR-5000 Manuel utilisateur

Avson

Avson MKT Platform Manuel utilisateur

Sony

Sony MEX-1HD - Audio Library System Manuel utilisateur

Pioneer

Pioneer DVH-P500UB Manuel utilisateur

JVC

JVC KD-AHD69 Manuel utilisateur

Blaupunkt

Blaupunkt SANTIAGO CR 87 Manuel utilisateur

Sony

Sony CDX-4160 - Cd Receiver Manuel utilisateur

XFIRE AUDIO

XFIRE AUDIO BMW42S Manuel utilisateur

VDO

VDO CD 2253 Manuel utilisateur

Volvo

Volvo 13 84 580 Manuel utilisateur

ZENEC

ZENEC ZE-160DVD Manuel utilisateur