Bosch WZ14 Manuel utilisateur

WZ14 Integrated IR Bullet

Camera

WZ14

en Installation Manual

WZ14 Integrated IR Bullet Camera Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual | 2.0 | 2010.12

Table of Contents

1Safety 4

1.1 Safety Precautions 4

1.2 Important Safety Instructions 4

1.3 Important Notices 6

1.4 FCC & ICES compliance 9

1.5 CSA certification 11

1.6 Warranty / Limitation of Liability 11

2 Introduction 14

2.1 Parts Included 14

3 Installation 15

4 Connection 17

4.1 Connection 17

5 Technical Specifications 18

4en | Safety WZ14 Integrated IR Bullet Camera

| 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.

1Safety

1.1 Safety Precautions

1.2 Important Safety Instructions

Read, follow, and retain all of the following safety instructions.

Heed all warnings on the unit and in the operating instructions

before operating the unit.

1. Read these instructions.

2. Keep this instruction.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a clean, soft, dry or moistened cloth and

mild detergent solution.

7. Do not block any ventilation openings. Install in

accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves or other apparatus (including amplifiers)

that produce heat.

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as “Dangerous Voltage” inside the product.

If not avoided, this will result in an electrical shock, serious

bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of

damage to the unit.

WZ14 Integrated IR Bullet Camera Safety | en 5

Bosch Security Systems, Inc. Installation Manual | 2.0 | 2010.12

9. Do not put objects inside the camera. Make sure that no

metal objects or flammable substances enter the camera.

This may cause fire, short-circuits and other damages.

10. Be careful when handling the camera. To prevent damage,

do not drop the camera or subject it to strong shock or

vibration.

11. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong is provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

12. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

power where they exit from the apparatus.

13. Protect the camera from humidity and dust.

14. Unplug this apparatus during lightning storms or when

unused for long periods of time.

15. Use only attachments/accessories specified by the

manufacturer.

16. Use only with the bracket sold with the apparatus.

17. Do not attempt to open or disassemble the camera to gain

access to the internal components. Refer all servicing to

qualified service personnel. Servicing is required when the

apparatus has been damaged in a way, such as power-

supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, does not operate

normally, or has dropped. When servicing, power shall be

disconnected.

18. These servicing instructions are for use by qualified service

personnel only. To reduce the risk of electric shock, do not

perform any servicing other than that contained in the

operating instructions, unless you are qualified to do so.

6en | Safety WZ14 Integrated IR Bullet Camera

| 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.

1.3 Important Notices

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

switch as the main disconnect device for switching off the

voltage to the unit.

Camera grounding - For mounting the camera in potentially

damp environments, ensure to ground the system using the

ground connection of the power supply connector (see section:

Connecting external power supply).

Camera lens - An assembled camera lens in the outdoor

housing must comply and be tested in accordance with UL/

IEC60065. Any output or signal lines from the camera must be

SELV or Limited Power Source. For safety reasons the

environmental specification of the camera lens assembly must

be within the environmental specification of -10 °C to 50 °C

(14°Fto122°F).

Camera signal - Protect the cable with a primary protector if

the camera signal is beyond 140 feet, in accordance with

NEC800 (CEC Section 60).

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury and/or serious damage to the unit. Use only with the

cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, use caution and care when

moving the cart/apparatus combination to avoid injury from

tip-over. Quick stops, excessive force, or uneven surfaces may

cause the cart/unit combination to overturn. Mount the unit

per the manufacturer's instructions.

WZ14 Integrated IR Bullet Camera Safety | en 7

Bosch Security Systems, Inc. Installation Manual | 2.0 | 2010.12

Coax grounding:

– Ground the cable system if connecting an outside cable

system to the unit.

– Connect outdoor equipment to the unit's inputs only after

this unit has had its grounding plug connected to a

grounded outlet or its ground terminal is properly

connected to a ground source.

– Disconnect the unit's input connectors from outdoor

equipment before disconnecting the grounding plug or

grounding terminal.

– Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

U.S.A. models only - Section 810 of the National Electrical Code,

ANSI/NFPA No.70, provides information regarding proper

grounding of the mount and supporting structure, grounding of

the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

Electronic Surveillance - This device is intended for use in

public areas only. U.S. federal law strictly prohibits

surreptitious recording of oral communications.

Environmental statement - Bosch has a strong commitment

towards the environment. This unit has been designed to

respect the environment as much as possible.

Disposal - Your Bosch product was developed and

manufactured with high-quality material and components that

can be recycled and reused. This symbol means that electronic

and electrical appliances, which have reached the end of their

working life, must be collected and disposed of separately from

household waste material. Separate collecting systems are

usually in place for disused electronic and electrical products.

Please dispose of these units at an environmentally compatible

recycling facility, per European Directive 2002/96/EC.

8en | Safety WZ14 Integrated IR Bullet Camera

| 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.

Electrostatic-sensitive device - Use proper CMOS/MOS-FET

handling precautions to avoid electrostatic discharge.

NOTE: Wear required grounded wrist straps and observe proper

ESD safety precautions when handling the electrostatic-

sensitive printed circuit boards.

Moving - Disconnect the power before moving the unit. Move

the unit with care. Excessive force or shock may damage the

unit and the hard disk drives.

Outdoor signals - The installation for outdoor signals, especially

regarding clearance from power and lightning conductors and

transient protection, must be in accordance with NEC725 and

NEC800 (CEC Rule 16-224 and CEC Section 60).

Permanently connected equipment - Incorporate a readily

accessible disconnect device external to the equipment.

Pluggable equipment - Install the socket outlet near the

equipment so it is easily accessible.

Power resupply - If the unit is forced to power down due to

exceeding the specified operating temperatures, disconnect

the power cord, wait for at least 30 seconds, and then

reconnect the power cord.

Power lines - Do not locate the camera near overhead power

lines, power circuits, or electrical lights, nor where it may

contact such power lines, circuits, or lights.

SELV - All the input/output ports are Safety Extra Low Voltage

(SELV) circuits. SELV circuits should only be connected to

other SELV circuits.

Because the ISDN circuits are treated like telephone-network

voltage, avoid connecting the SELV circuit to the Telephone

Network Voltage (TNV) circuits.

System ground/Safety ground

System (video) ground is indicated by the symbol .

Safety (power) ground is indicated by the symbol .

The system ground is only used to comply with safety standards

or installation practices in certain countries. Bosch does not

recommend connecting system ground to safety ground unless

it is explicitly required. However, if the system ground and

WZ14 Integrated IR Bullet Camera Safety | en 9

Bosch Security Systems, Inc. Installation Manual | 2.0 | 2010.12

safety ground are connected and grounding loops are causing

interference in the video signal, use an isolation transformer

(available separately from Bosch).

Video loss - Video loss is inherent to digital video recording;

therefore, Bosch Security Systems cannot be held liable for any

damage that results from missing video information. To

minimize the risk of lost digital information, Bosch Security

Systems recommends multiple, redundant recording systems,

and a procedure to back up all analog and digital information.

1.4 FCC & ICES compliance

FCC & ICES Information

(U.S.A. and Canadian Models Only)

This device complies with part 15 of the FCC Rules. Operation is

subject to the following conditions:

– this device may not cause harmful interference, and

– this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply

with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules and ICES-003 of Industry Canada. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and radiates

radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct

the interference at his expense.

Intentional or unintentional modifications, not expressly

approved by the party responsible for compliance, shall not be

CAUTION!

Connecting System ground to Safety ground may result in

ground loops that can disrupt the CCTV system.

10 en | Safety WZ14 Integrated IR Bullet Camera

| 2.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.

made. Any such modifications could void the user's authority to

operate the equipment. If necessary, the user should consult

the dealer or an experienced radio/television technician for

corrective action.

The user may find the following booklet, prepared by the

Federal Communications Commission, helpful: How to Identify

and Resolve Radio-TV Interference Problems. This booklet is

available from the U.S. Government Printing Office,

Washington, DC 20402, Stock No. 004-000-00345-4.

Informations FCC et ICES

(modèles utilisés aux États-Unis et au Canada uniquement)

Ce produit est conforme aux normes FCC partie 15. la mise en

service est soumises aux deux conditions suivantes :

– cet appareil ne peut pas provoquer d'interférence nuisible

– cet appareil doit pouvoir tolérer toutes les interférences

auxquelles il est soumit, y compris les interférences qui

pourraient influer sur son bon fonctionnement.

AVERTISSEMENT: Suite à différents tests, cet appareil s’est

révélé conforme aux exigences imposées aux appareils

numériques de Classe A en vertu de la section 15 du règlement

de la Commission fédérale des communications des États-Unis

(FCC). Ces contraintes sont destinées à fournir une protection

raisonnable contre les interférences nuisibles quand l'appareil

est utilisé dans une installation commerciale. Cette appareil

génère, utilise et émet de l'energie de fréquence radio, et peut,

en cas d'installation ou d'utilisation non conforme aux

instructions, générer des interférences nuisibles aux

communications radio. L’utilisation de ce produit dans une

zone résidentielle peut provoquer des interférences nuisibles.

Le cas échéant, l’utilisateur devra remédier à ces interférences

à ses propres frais.

Au besoin, l’utilisateur consultera son revendeur ou un

technicien qualifié en radio/télévision, qui procédera à une

opération corrective. La brochure suivante, publiée par la

Commission fédérale des communications (FCC), peut s’avérer

Autres manuels pour WZ14

Table des matières

Autres manuels Bosch Caméra de sécurité

Bosch

Bosch FlexiDome NDN-832 Manuel utilisateur

Bosch

Bosch FLEXIDOME IP micro 3000i-outdoor Manuel utilisateur

Bosch

Bosch FLEXIDOME 5000 Instructions d'utilisation

Bosch

Bosch NCD-274-PM Manuel utilisateur

Bosch

Bosch FCS-8000-VFD-B Manuel utilisateur

Bosch

Bosch Onvif NTC-255-PI Manuel utilisateur

Bosch

Bosch WZ14N4-0 Manuel utilisateur

Bosch

Bosch DINION IP imager 9000 HD Manuel utilisateur

Bosch

Bosch FlexiDomeVF VDM-345V03-20 Manuel utilisateur

Bosch

Bosch VJR-F801-ICCV Manuel utilisateur

Bosch

Bosch KBE-495V28-20N Manuel utilisateur

Bosch

Bosch DINION IP starlight 7000 HD Manuel utilisateur

Bosch

Bosch HD Conference Dome Camera Manuel utilisateur

Bosch

Bosch FlexiDome NDC-455V03-21P Manuel utilisateur

Bosch

Bosch DINION XF LTC 0495 Guide d'installation

Bosch

Bosch Compact Day-Night WZ14N4-0 (NTSC) Manuel utilisateur

Bosch

Bosch EX65 Manuel utilisateur

Bosch

Bosch Junior Guide d'installation

Bosch

Bosch Divar 700 Series Manuel du propriétaire

Bosch

Bosch NBN-80052 Manuel utilisateur

Bosch

Bosch LTC 0455 Series Manuel

Bosch

Bosch VEN-650V05-2A3 Manuel utilisateur

Bosch

Bosch FlexiDome NDN-498V03-21P Manuel utilisateur

Bosch

Bosch DINION IP 4000i IR Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur