Bosch PVA-4R24 Manuel utilisateur

PAVIRO Router

PVA-4R24

en Operation manual

Table of contents

1Safety 4

2Short information 8

3System overview 9

3.1 Front panel 9

3.2 Rear panel 11

4Parts included 12

5Installation 13

6Connection 15

6.1 Audio input 15

6.2 Audio output 16

6.3 Supply voltage 17

6.4 CAN BUS 18

6.5 Control input 20

6.6 Control output 21

7Configuration 24

7.1 Setting the CAN address 24

7.2 Displaying the CAN baud rate 25

7.3 Configuring the CAN baud rate 25

8Operation 26

8.1 Line supervision 26

8.1.1 Impedance measurement 26

8.1.2 EOL slave module 26

8.1.3 Plena EOL 27

8.2 Pilot tone 28

9Maintenance 29

9.1 Firmware update 29

9.2 Resetting to factory default settings 29

10 Technical data 30

10.1 Standards 31

10.2 Dimensions 31

PAVIRO Router Table of contents | en 3

Operation manual 12-May-2015 | 03 | F01U306901

Safety

Danger!

High risk: This symbol indicates an imminently hazardous situation such as "Dangerous

Voltage" inside the product.

If not avoided, this will result in an electrical shock, serious bodily injury, or death.

Warning!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily injury.

Caution!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of damage to the unit.

1. Read these instructions. – All the safety and operating instructions should be read

before the apparatus or system is operated.

2. Keep these instructions. – The important safety instructions and operating instructions

should be retained for future reference.

3. Heed all warnings. – All warnings on the apparatus and in the operating instructions

should be adhered to.

4. Follow all instructions. – All instructions for installation or use/operating should be

followed.

5. Do no use this apparatus near water. – Do not use this apparatus near water or a moist

environment - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a

wet basement, near a swimming pool, in an unprotected outdoor installation, or any area

which is classified as a wet location.

6. Clean only with dry cloth. – Unplug the apparatus from the outlet before cleaning. Do

not use liquid cleaners or aerosol cleaners.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions. – Openings in the enclosure, if any, are provided for ventilation and to

ensure reliable operation of the apparatus and to protect it from overheating. These

openings must not be blocked or covered. This apparatus should not be placed in a built-

in installation unless proper ventilation is provided or the manufacturer’s instructions

have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat or in direct sunlight.

9. No naked flame sources, such as lighted candles, should be placed on the apparatus.

10. Do not defeat the safety purpose of the polarized or ground-type plug. – A polarized

plug has two blades with one wider than the other. A grounding type plug has two blades

and a third grounding prong. The wider blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

11. Protect the power cord from being walked on or pinched particularly at plug,

convenience receptacles, and the point where they exit from the apparatus.

12. Only use attachments/accessories specified by the manufacturer. – Any mounting of the

apparatus should follow the manufacturer’s instructions, and should use a mounting

accessory recommended by the manufacturer.

4en | Safety PAVIRO Router

12-May-2015 | 03 | F01U306901 Operation manual

13. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, or

sold with the apparatus. – When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart combination to overturn.

14. Unplug this apparatus during lighting storms or when unused for long periods of time.

– Not applicable when special functions are to be maintained, such as evacuation

systems.

15. Refer all servicing to qualified service personnel. – Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

16. The apparatus shall not be exposed to dripping or splashing and that no objects filled

with liquid, such as vases, shall be placed on the apparatus.

17. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat

such as sunshine, fire or the like.

Caution!

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type. Dispose of used batteries according to the environmental law and

procedures.

18. Professional installation only – Do not use this equipment in residential applications.

19. Condensation – In order to avoid condensation; wait a few hours before turning on the

equipment when it is transported from a cold to a warm space.

20. Hearing damage – For apparatus with audio output, to prevent possible hearing damage,

do not listen at high volume levels for long periods.

21. Replacement parts – When replacement parts are required, be sure the service

technician has used replacement parts specified by the manufacturer or having the same

characteristics as the original part. Unauthorized substitutions may result in fire, electric

shock or other hazards.

22. Safety check – Upon completion of any service or repairs to this apparatus, ask the

service technician to perform safety checks to determine that the apparatus is in proper

operating condition.

Danger!

Overloading – Do not overload outlets and extension cords as this can result in a risk of fire or

electric shock.

23. Power sources – This apparatus should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power supply you plan to

use, consult your appliance dealer or local power company. For apparatuses intended to

operate from battery power, or other sources, refer to the operating instructions.

24. Power lines – An outdoor system should not be located in the vicinity of overhead power

lines or other electric light or power circuits, or where it can fall into such power lines or

circuits. When installing an outdoor system, extreme care should be taken to keep from

touching such power lines or circuits, as contact with them might be fatal. U.S.A. models

only – refer to the National Electrical Code Article 820 regarding installation of CATV

systems.

PAVIRO Router Safety | en 5

Operation manual 12-May-2015 | 03 | F01U306901

Danger!

Object and Liquid entry – Never push objects of any kind into this apparatus through

openings as they may touch dangerous voltage points or short-out parts that could result in a

fire or electric shock. Never spill liquid of any kind on the apparatus.

25. Coax grounding – If an outside cable system is connected to the apparatus, be sure the

cable system is grounded. U.S.A. models only: Section 810 of the National Electrical

Code, ANSI/NFPA No.70-1981, provides information with respect to proper grounding of

the mount and supporting structure, grounding of the coax to a discharge apparatus, size

of grounding conductors, location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

26. Protective grounding – An apparatus with class I construction shall be connected to a

power outlet socket with a protective grounding connection.

Protective earthing – An apparatus with class I construction shall be connected to a

mains socket outlet with a protective earthing connection.

Note for power connections

– For permanently connected equipment, a readily operable mains plug or all-pole mains

switch shall be external to the equipment and in accordance with all applicable

installation rules.

– For pluggable equipment, the socket-outlet shall be installed near the equipment and

shall be easily accessible.

This label may appear on the bottom of the apparatus due to space limitations.

Caution!

To reduce the risk of electrical shock, DO NOT open covers. Refer servicing to qualified

service personnel only.

Warning!

To prevent fire or shock hazard, do not expose units to rain or moisture.

Warning!

Installation should be performed by qualified service personnel only in accordance with the

National Electrical Code or applicable local codes.

Warning!

Power disconnect: If the apparatus is mains powered and a power supply cord set is

provided, the disconnect device is the mains plug of the power cord set.

If an AC‑DC adapter is provided and the mains plug that is part of the direct plug‑in device,

the AC‑DC adapter is the disconnect device.

The socket outlet shall be near the apparatus and shall be easily accessible.

6en | Safety PAVIRO Router

12-May-2015 | 03 | F01U306901 Operation manual

Warning!

To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-

network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV

circuits. Some LAN and WAN ports both use RJ‑45 connectors. Use caution when connecting

cables.

Old electrical and electronic appliances

Electrical or electronic devices that are no longer serviceable must be collected separately and

sent for environmentally compatible recycling (in accordance with the European Waste

Electrical and Electronic Equipment Directive).

To dispose of old electrical or electronic devices, you should use the return and collection

systems put in place in the country concerned.

Only used at

altitude not

exceeding 2000m.

Only used in non-

tropical climate

regions.

PAVIRO Router Safety | en 7

Operation manual 12-May-2015 | 03 | F01U306901

Short information

The PVA-4R24 24 Zone Router is a zone extension for the PAVIRO system. The PVA-4R24 adds

24 zones, 20 GPIs, 24 GPOs and 2 control relays to the system and is controlled and

supervised via the CAN bus by the PVA-4CR12 (Controller). Up to 20 external routers can be

connected to one controller. One router can handle up to 4000 W speaker load. The maximum

load of one zone is 500 W.

The zone indicator lights on the front indicate the current status of every zone:

– Green: Zone in use for non emergency purpose

– Red: Zone in use for emergency purpose

– Yellow: Zone fault detected

– Off: Zone in idle condition

8en | Short information PAVIRO Router

12-May-2015 | 03 | F01U306901 Operation manual

System overview

Front panel

Number Symbol Element Description

1 Zone status

indicator light

Indicates the status of the zone:

– Green = Zone is in use for non-emergency

purpose

– Yellow = Zone fault detected (Note: The

indication of this status has the highest

priority)

– Red = Zone is in use for emergency purpose

– Off = Zone in idle condition

2 General fault

warning indicator

light

This indicator lights up yellow if a fault in the

device is detected.

Note: The fault types to be indicated via this

indicator can be configured.

3.1

PAVIRO Router System overview | en 9

Operation manual 12-May-2015 | 03 | F01U306901

Number Symbol Element Description

3 Recessed button The button is protected to prevent it from being

pressed accidentally. Use a pointed object (such

as a ballpoint pen) to press the button.

This button has the following functions if the CAN

address of the device is not set to 00:

– Find function: If the find function of the

device is activated, press this button to

deactivate the indicators.

– Displaying the CAN baud rate: Press this

button for at least one second. Please refer to

section Displaying the CAN baud rate, page

25.

– LED test: Press this button for at least three

seconds to activate the LED test. All

indicators at the front panel light up as long

as the button is pressed.

This button has the following functions if the CAN

address of the device is set to 00:

– Resetting a fault (e.g. watchdog fault): Press

the button briefly to confirm a fault.

– Setting/displaying the CAN baud rate: Press

this button for at least one second. Please

refer to section Configuring the CAN baud rate,

page 25.

– Resetting to delivery condition: Press this

button for at least three seconds. Please refer

to section Resetting to factory default settings,

page 29.

4Network indicator

light

This indicator lights up green if successful data

communication has been established.

5 Standby indicator

light

This indicator lights up green when the device is in

standby mode.

6 Power indicator

light

This indicator lights up green when the power

supply is OK.

10 en | System overview PAVIRO Router

12-May-2015 | 03 | F01U306901 Operation manual

Autres manuels pour PVA-4R24

Table des matières

Autres manuels Bosch Routeur réseau

Bosch

Bosch GKF 550 Manuel utilisateur

Bosch

Bosch 1618EVS - 2-1/4 HP Electronic Fixed Base D Handle... Manuel utilisateur

Bosch

Bosch 1619EVS - NA 3.25 HP Electronic Plunge... Instructions de montage

Bosch

Bosch 7 620 320 029 Manuel utilisateur

Bosch

Bosch 601613639 Manuel utilisateur

Bosch

Bosch 1613AEVS Instructions de montage

Bosch

Bosch 1618EVS - 2-1/4 HP Electronic Fixed Base D Handle... Instructions de montage

Bosch

Bosch PR10E Instructions de montage

Bosch

Bosch PVA-4R24 Manuel utilisateur

Bosch

Bosch 1619EVS - NA 3.25 HP Electronic Plunge... Manuel utilisateur

Bosch

Bosch ATM/POS Bridge Manuel utilisateur

Bosch

Bosch GOF 1250 CE Manuel utilisateur

Bosch

Bosch GKF 600 Professional Manuel utilisateur

Bosch

Bosch Mastertech M-VCI Manuel utilisateur

Bosch

Bosch 1619EVS - NA 3.25 HP Electronic Plunge... Instructions de montage

Bosch

Bosch GMF 1400 CE Professional Manuel utilisateur

Bosch

Bosch 10601617739 Manuel utilisateur

Bosch

Bosch GMF 1400 CE Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité