Bosch DMO 10 E Manuel utilisateur

Operating instructions

Bruksanvisning

Brukerveiledningen

Käyttöohje

English

Dansk

Svenska

Norsk

Suomi

DMO 10 E

1234

789

English–1

1 609 929 C79 • (01.10) T

≈

* Dependent on the size, depth and type of metal as well as the material and

condition of the wall (e.g. moisture)

1“Allowable Drilling Depth” function

2Green “Drilling Possible” LED indicator

3Red “Do not Drill” LED indicator

4Display

5Handle area with brief operating instructions

6Battery compartment cover

7“Search” function

8Rotary switch

9Marking stamp

10 On/calibration button on/cal

11 Stamping ring

12 Protective bag

Display Elements

aMeasured value of the drilling depth measurement

bBar indicator for Metal detection and drilling depth measurement

cCalibration indicator CAL

dIndicator for voltage carrying wiring in the measurement area

eMeasuring unit in mm for the drilling depth measurement

fBattery indicator

The unit is intended for the detection of metal (e.g. reinforcing iron)

and mains wiring in ceilings and walls.

Product Specifications

Digital Metal Detector DMO 10 E

Order number 0 603 096 601

Maximum detection depth*

Steel to approx.

Copper to approx. 50 mm

30 mm

Automatic switch-off after approx. 75 s

Operating temperature –5 °C ... +50 °C

Storage temperature – 20 °C ... +85 °C

Battery 9 V DC 6LR 61

Weight (with battery) approx. 350 g

Product Elements

Intended Use

English–2

1 609 929 C79 • (01.10) T

Working safely with this machine is possible

only when the operating and safety informa-

tion are read completely and the instructions

contained therein are strictly followed.

■Protect the unit from moisture and direct sunrays.

■If the unit is not used for a longer time, the battery must be re-

moved (danger of self-discharge and corrosion).

Use Alkali-Manganese batteries exclusively.

Open the battery compartment cover 6and insert the battery pro-

vided.

If the symbol appears on the display 4, erroneous measure-

ment cannot be excluded. This means that, with a weak battery, it

cannot be ensured that the unit functions in an error-free manner.

The battery is exhausted and must be replaced.

Open the battery compartment cover 6and replace the battery.

Before switching on, set the rotary switch 8to the

function. If the function was selected before switching

on, the unit switches itself off again immediately after the

calibration.

Switching on: For each individual depth measurement, ensure

that the rotary switch 8is first set to the

function.

During switching on and the subsequent calibra-

tion, hold the unit so that no objects are located

within at least 0.5 m in the measuring direction.

Hold the unit with the hand around the handle

area 5. Only in this manner is an error-free cali-

bration ensured.

For Your Safety

Protection of the Unit

Inserting/Replacing the Batteries

Putting into Operation

English–3

1 609 929 C79 • (01.10) T

Press the On/Cal button 10 on the back of the

unit.

The unit switches on and calibrates itself auto-

matically. During this period, the red LED indica-

tor 3and the green LED indicator 2blink alter-

nately. In the display, the blinking CAL symbol

indicates that the calibration is in progress.

After approx. 3 s, the CAL symbol disappears

from the display. The display shown here ap-

pears. The green LED indicator 2lights.

The unit is now ready for operation.

Switching off:

After approx. 75 s without renewed calibration, the device switches

off automatically.

■Warning: Under certain conditions, this detector may

give erroneous readings. Do not rely completely on this

detector to assure safe operation when drilling or cutting

into walls with live electrical wiring, pressurized water

pipes, etc.

■Always follow precautions outlined in the operating man-

ual for your drill, saw, etc.

Measurement behind surfaces containing metal (e.g. tiles with me-

tallic content) are not or only conditionally possible since the unit

detects and indicates the metal of the surface.

Calibration

Renewed calibration is always required when the CAL symbol

blinks (every 60 s) in the display 4during operation. In addition, cal-

ibration is to be performed when the device is given to another per-

son.

Observe the instructions for calibration in the Switching On section.

Set the rotary switch 8to the function. Press the On/Cal but-

ton 10 on the back of the unit.

Marking

Important positions can be marked as necessary. For this pur-

pose, place the unit on the position to be marked (e.g. drilling po-

sition) and press the marking stamp 9lightly against the surface.

If the marking intensity of the stamp ring becomes weak, replace

the marking stamp 9.

Insert a coin or similar object into the slot of the marking stamp 9

and turn until a click is audible (see Figure ). Tilt the coin slightly

to lift the marking stamp 9upward. Pull the marking stamp 9com-

pletely out.

Insert a new stamp (see Figure ) and turn with the coin until it

clicks.

Working Instructions

English–4

1 609 929 C79 • (01.10) T

“Search” Function

Put the unit into operation. The green LED indi-

cator 2lights.

Place the unit with the complete back side on

the surface to be checked and move over the

search area.

When metal is detected, the red LED indicator 3

lights and the bar indicator in the display 4in-

creases in height.

Continue to move over the surface until the bar

indicator reaches a maximum, decreases again

and the red LED indicator 3goes out.

For the exact localisation, move over the search

area several times from both directions so that

the red and green LED indicators light alternate-

ly. In this manner, the unit adjusts its sensitivity

automatically.

Only when the green LED indicator 2lights con-

tinuously within the search area and the bar indi-

cator shows unchanged a single bar, no metal or

voltage carrying wiring was found. If the green

LED indicator lights and several bars are shown,

an unambiguous indication is not possible.

If the unit finds metal, the green LED indicator 2

goes out and the red LED indicator 3lights. The

bar indicator in the display 4increases in height.

The increase in height is dependent on the size,

depth and type of metal as well as the material of

the wall. The height increases with the proximity.

The position of the detected metal can be local-

ised better when observing the maximum deflec-

tion of the bar display.

Electrical wiring that does not carry voltage is

detected when it is not too deep.

☞Before drilling, determine the depth of the metal (see

“Allowable Drilling Depth” Function).

The blinking symbol and the red LED indicator

3signal voltage carrying mains wiring. If the

metal of the mains wiring is in the detection

range of the unit, the height of the bar indicator

increases. With the aid of the maximum height,

the position of the mains wiring can be localised

exactly.

No drilling may be performed at this loca-

tion.

A depth measurement of voltage carrying wiring

is not possible.

Measurement Functions

English–5

1 609 929 C79 • (01.10) T

When placing on the wall or for quick movements, the symbol

can appear briefly without any electrical cable being found in the

measurement area.

The following wiring is recognised as metal objects but not

as live electrical cable conductors:

– Mains wiring in moist walls

– Mains wiring which are not live

– Three phase mains wiring (e.g. kitchen stove)

– Shielded wiring (e.g. antenna cable)

The following wiring is generally not recognised:

– Extra-low voltage wiring (e.g. telephone, door bell)

– Mains wiring behind surfaces containing metal

“Allowable Drilling Depth” Function

Caution: Use this function only for reinforcing iron in concrete.

When the depth of reinforcing iron in concrete is

to be determined after successfully location the

metal (see “Search” Function), move the unit to

the location of maximum bar indicator height.

Set the rotary switch 8to the function.

The unit head is lifted. Hold the unit in position

and do not move it.

Read permitted drilling depth on the display 4.

Note: The range of the drilling depth indicator

on the display 4is to 90 mm, however, detection

to this depth is not possible.

For each additional individual depth measure-

ment, first set the rotary switch 8again to the

function and then move to the new location.

Protective bag . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 609 203 D80

Stamping ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 609 302 144

Battery compartment cover . . . . . . . . . . . . . . . . . .1 609 302 127

Replacement Parts

English–6

1 609 929 C79 • (01.10) T

■Always keep the metal detector clean so that it functions prop-

erly and accurately.

Use dry cloth for cleaning.

If the unit should fail despite the care taken in manufacture and

testing, repair should be carried out by an authorised customer

services agent for Bosch power tools.

For all correspondence and spare parts orders, always include the

10-digit order number of the unit.

We guarantee Bosch products in accordance with statutory/

country-specific regulations (proof of purchase by invoice or deliv-

ery note).

Damage attributable to normal wear and tear, overload or improper

handling will be excluded from the guarantee.

In case of a claim, please send the unit, completely assembled,

to your dealer or a Bosch Service Centre for pneumatic tools or

power tools.

Recycle raw materials instead of disposing

as waste.

Unit, accessories and packaging should be sorted

for environment-friendly recycling.

These instructions are printed on recycled paper

manufactured without chlorine.

The plastic components are labelled for categorized recycling.

Do not throw used batteries into household waste, fire or water, but

rather – according to the applicable legal regulations – dispose of

in an environmentally friendly manner.

Maintenance and Cleaning

Guarantee

Environmental Protection

English–7

1 609 929 C79 • (01.10) T

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham-Uxbridge

GB-Middlesex UB 9 5HJ

✆Service . . . . . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95/83 87 82

✆Advice line . . . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95/83 87 91

Fax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95/83 87 89

Ireland

Beaver Distribution Ltd.

Greenhills Road

IRL-Tallaght-Dublin 24

✆Service . . . . . . . . . . . . . . . . . . . . . . . . . . + 353 (0)1/414 9400

Fax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . + 353 (0)1/459 8030

Australia

Robert Bosch Australia L.t.d.

RBAU/SBT2

1555 Centre Road

P.O. Box 66 Clayton

AUS-3168 Clayton/Victoria

✆. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +61 (0)1/800 804 777

Fax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +61 (0)1/800 819 520

www.bosch.com.au

E-Mail: [email protected]

New Zealand

Robert Bosch Limited

14-16 Constellation Drive

Mairangi Bay

Auckland

New Zealand

✆. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +64 (0)9/47 86 158

Fax. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +64 (0)9/47 82 914

Specification subject to alteration without notice

Service and Customer Advice

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Bosch Détecteur de métaux

Bosch

Bosch GMS 120 Professional Manuel utilisateur

Bosch

Bosch PMD 10 Manuel utilisateur

Bosch

Bosch Professional GMS 100 M Manuel utilisateur

Bosch

Bosch PDO Multi Manuel utilisateur

Bosch

Bosch GMS 120 Manuel utilisateur

Bosch

Bosch GMS 120 Professional Instructions de montage

Bosch

Bosch PMD 7 Manuel utilisateur

Manuels Détecteur de métaux populaires d'autres marques

Garrett

Garrett MAGNASCANNER CS 5000 Manuel utilisateur

Valex

Valex 1800200 Manuel utilisateur

Gauss

Gauss MIL MD Manuel utilisateur

Velleman

Velleman CS130 Manuel utilisateur

Sears

Sears 321.596370 Manuel utilisateur

Eriez

Eriez X8 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-22 Manuel utilisateur

Zircon

Zircon MetalliScanner m60c Manuel utilisateur

nalanda

nalanda MD027 Manuel utilisateur

REV Ritter

REV Ritter CB-7005 Manuel utilisateur

Minelab

Minelab F1A4 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs F70 Manuel utilisateur

Steinberg Systems

Steinberg Systems SBS-MD-12 Manuel utilisateur

GOLDEN MASK

GOLDEN MASK 5 Manuel utilisateur

Grizzly

Grizzly YM 203 Manuel utilisateur

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Manuel utilisateur

Treasure Cove

Treasure Cove Vibra-Probe 560 Manuel utilisateur

Accurate Locators

Accurate Locators XL16 IMAGER Manuel utilisateur