Bosch Rexroth EFC 3600 Instructions d'utilisation

Easy Start Guide

This guide is intended to compliment the user manual provided by the manufacturer.

It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.

It should not be used as a replacement for the manual issued by the manufacturer.

Issue 2

20140924

This product is not a safety device. All safety considerations including but not

limited to Emergency Stop provision should be assessed separately and are

outside the scope of this guide.

Bosch Rexroth

EFC 3600 Frequency Inverter

available from Rexroth.InverterDrive.com

(+)

Easy Start Guide

Page 1

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Page 13

Contents

Power and Motor Connections (Single Phase)

Power and Motor Connections (Three Phase)

Motor Connections - Star and Delta

Parameters - Overview

Parameters to set before use

How to Operate the Inverter from the keypad

How to connect and configure a Potentiometer

for remote speed control

How to connect and configure a Run Forward or

Run Reverse switch

Brake Resistor Connection

How to Reset the Inverter to Factory Defaults

How to set a Parameter value

How to connect and configure a Run/Stop switch

with Forward/Reverse selection

How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection

Contents

Bosch Rexroth EFC 3600 Series Inverter

Easy Start Guide

1. Power and Motor Connections (Single Phase)

Page 2

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration above is based on the frame

size B model (0.75kW). The terminal layout for

sizes A, C and D (0.37kW, 1.5kW and 2.2kW is

similar.

The order of the three phases determines the

direction the motor turns.

Important:

Use screened SY cable between the Inverter

and Motor to minimise electromagnetic

interference.

Ensure the motor cable screen is earthed at

the motor end.

Before commencing, confirm that the Inverter and

all cables are completely isolated from the power

supply, have been isolated for at least 5 minutes

and that the motor is not turning.

Bosch Rexroth EFC 3600 Series Inverter

(+)

MotorPower

Phase

Earth

Live

Neutral

Earth

Easy Start Guide

2. Power and Motor Connections (Three Phase)

Page 3

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration above is based on the frame

size B model (0.75kW). The terminal layout for

other frame sizes is similar.

The order of the three motor phases

determines the direction the motor turns.

The order of the three power phases is

unimportant.

Important:

Use screened SY cable between the Inverter

and Motor to minimise electromagnetic

interference.

Ensure the motor cable screen is earthed at

the motor end.

Before commencing, confirm that the Inverter and

all cables are completely isolated from the power

supply, have been isolated for at least 5 minutes

and that the motor is not turning.

Bosch Rexroth EFC 3600 Series Inverter

(+)

MotorPower

Phase

Earth

Phase

Earth

Easy Start Guide

3. Motor Connections - Star and Delta

Page 4

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

3.2 Motor connected in DELTA:

The link configuration is shown in the

illustration opposite and is sometimes referred

to as “three-a-breast”.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the earth terminal.

Phase

Earth

Screen

3.1 Motor connected in STAR (or Wye):

For safety purposes, Star (shown opposite) is

the default configuration for new motors and is

sometimes known as “two at one side”.

Only two links are required for Star. Double-up

the links if changing from Delta to allow the

motor to be changed to back in future.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the earth terminal.

Phase

Earth

Screen

Dual voltage induction motors typically include

terminal boxes with six points. The points can

be connected together with links in one of two

ways to suit one of the two rated voltages.

The two ways of connecting the links are

shown below. These are known as “Star” (the

higher voltage) or “Delta” (the lower voltage).

Link

The selection of Star or Delta is not optional

and must match the supply voltage.

Dual voltage motor nameplates include

symbols to represent voltage and full load

current in each configuration.

Delta is represented by a triangle and star by a

Y (Wye).

DELTA

STAR

Link

Bosch Rexroth EFC 3600 Series Inverter

Easy Start Guide

Page 5

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

4. Parameters - overview

Parameter

Description

How to set

b0.02

Access to additional parameters

Set at to enable Extended Parameters ( .2Default is 0 for Basic Parameters)

b1.05

Maximum Frequency

Maximum frequency of the . Set to for most applications.Inverter 50.00

b1.06

Upper Frequency

Maximum frequency of .speed reference (eg. keypad dial) Set to for most applications.50.00

b1.07

Minimum Frequency

Set to for most applications (Default is 00.00).05.00

b1.08

Lower frequency mode

Set to to enable Minimum Frequency.1

b1.20

Acceleration ramp in seconds

Default is . Increase or decrease if required.5

b1.21

Deceleration ramp in seconds

Default is . Increase or decrease if required.5

S0.00

V/F curve mode

Default is . Set to 1 if the motor is driving a Fan or Pump.0

S2.00

Rated motor frequency in Hz

Default is 50.00. Change to 60.00 for 60Hz motor only - otherwise set at 50.00

S2.01

Rated motor speed in rpm

Set to match motor nameplate - eg. 1380

S2.02

Rated motor power in kW

Set to match motor nameplate - eg. 0.8 (for 0.75kW)

S2.03

Rated motor voltage

Set to match motor nameplate - eg. 230

S2.04

Rated motor current in A

Set to match motor nameplate - eg. 3.34

The Inverter contains a number of settings

which can be changed to tailor it for use in a

wide range of applications. These settings are

known as parameters.

Parameters are typically referred to by code or

number (eg. s2.04 = Rated Motor Current) with

a description available in the manual.

The parameters contain critical information

essential to the correct operation of the

Inverter. Therefore, they should at least be

checked by the user before the Inverter is

operated for the first time.

The parameters listed in section 5 are intended

to provide a starting point to allow for basic

operation of the EFC 3600 Inverter.

5. Parameters to set before use

See section 6 to learn how to set a parameter value.

Set the following parameters to allow the EFC

3600 to control a motor with Run, Stop and

Speed Control from the keypad.

If any of the parameters have been changed

previously, follow the procedure in section 13

to reset the Inverter to Factory Defaults.

5.1 Parameters to check and values to set

Bosch Rexroth EFC 3600 Series Inverter

Easy Start Guide

6. How to set a Parameter value

Page 6

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Bosch Rexroth EFC 3600 Series Inverter

6.1 Find Parameter Groups.

This example demonstrates the steps required to set

parameter b1.05 which is Maximum Frequency.

Press the “Func” key repeatedly until the display shows

“-b0-” (shown in the illustration opposite).

6.2 Find a Parameter Group eg. b1

There are a total of 12 parameter groups when

“Advanced Parameters” are enabled:-

Some parameter groups may be hidden when “Advanced

Parameters” are not enabled. Press “Set” to select “-b1-”.

6.3 Find a Parameter eg. b1.05

The display will show “b1.00" to indicate parameter 00

within group b1.

Use the up and down keys to navigate to parameter

b1.05. Press the “Set” key to modify the parameter value.

Note that in some cases, the value of a parameter can be

restricted by the value of another parameter.

6.4 Change a Parameter value.

Use the up and down keys to increase or decrease the

value. Press and hold the up or down key to change the

value more quickly.

Press the “Set” key to save changes. The display will

show the next available parameter.

Press “Func” twice to exit.

Easy Start Guide

7. How to operate the Inverter from the keypad

Page 7

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

7.1 Use the dial to set the required speed.

The display will change to show the current speed

reference in Hz.

The minimum speed reference is defined by parameter

b1.07 and the maximum reference by b1.06.

7.2 Press the green “Run” button to start the motor.

Press the green button firmly to start the motor. The motor

will accelerate to the speed set in 7.1 (above) in the time

defined by parameter b1.20.

Motor speed can be changed whilst the motor is running by

rotating the dial clockwise (faster) or anti-clockwise

(slower). When the motor is running, the “Run” lamp will be

illuminated.

7.3 Press the red “Stop” button to stop the motor.

The red button will stop the motor.

The time taken (in seconds) to stop the motor is determined

by parameter b1.21.

Bosch Rexroth EFC 3600 Series Inverter

Easy Start Guide

Page 8

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter

Drive Supermarket and must not be reproduced or altered without prior written permission.

Bosch Rexroth EFC 3600 Series Inverter

8. How to connect and configure a Potentiometer

for remote speed control

Parameter

Description

How to set

b0.02

Access to additional parameters

Default is 0 for Basic Parameters. Set at to enable Extended Parameters.2

b1.00

Frequency Setting Source

Set to to enable 0-10V via 10kOhm Potentiometer2

E0.22

Potentiometer Min Speed Hz

Set to for most applications.05.00

E0.24

Potentiometer Max Speed Hz

Set to for most applications.50.00

8.1 Parameters to change for remote Potentiometer speed control

If the integrated dial on the keypad is

unsuitable for the application, a remote

Potentiometer can be used instead.

This provides the benefit of allowing motor

speed to be controlled from a more convenient

location such as a cabinet door (if the EFC

3600 is cabinet-mounted) or on the machine

itself.

A Potentiometer of rating should be

used.

The number of turns depends on the

application but both single turn and ten turn

Potentiometers are available from The Inverter

Drive Supermarket at InverterDrive.com.

10kOhm

8.2 Connecting the Potentiometer

A wiring diagram is shown in the illustration

opposite. The most important connection at

the Potentiometer end is the centre terminal or

“wiper”.

The wiper will output a variable voltage

between 0 and 10 volts and should be

connected to the Vr1 terminal at the Inverter

end. It is this voltage which provides the speed

signal with 0V being slowest and 10V fastest.

The default output frequency at 0V is 0Hz. To

change this, edit Parameter E0.22. The default

output frequency at 10V is 50Hz. To change

this, edit Parameter E0.24.

If the rotation of the Potentiometer is the

opposite to that required (ie. turn anti-

clockwise to increase speed instead of

clockwise) reverse connections +10V and

GND.

Use shielded SY cable between Potentiometer

and Inverter and ensure that the cable screen

is connected to the earth IO terminal.

10kOhm

Potentiometer

[Order Code 21302]

Screened

“SY” Cable

Screen to

Earth Terminal

GND

+10VVr1

EFC 3600

I/O Terminal Blocks

Autres manuels pour Rexroth EFC 3600

Table des matières

Autres manuels Bosch Entraînement CC

Bosch

Bosch BDU3380 Manuel utilisateur

Bosch

Bosch BDU450 CX Manuel utilisateur

Bosch

Bosch REXROTH IndraDrive Manuel technique

Bosch

Bosch rexroth Sytronix SvP 7030 IMC Manuel utilisateur

Bosch

Bosch Performance Line Cargo Manuel utilisateur

Bosch

Bosch Rexroth AOK Manuel utilisateur

Bosch

Bosch Rexroth EFC 3600 Manuel utilisateur

Bosch

Bosch Rexroth Sytronix FcP 5020 Manuel utilisateur

Bosch

Bosch REXROTH HYDROTRAC GFT 8000 Manuel utilisateur

Bosch

Bosch Rexroth Sytronix SvP 7020 IMC Manuel utilisateur

Bosch

Bosch Rexroth KSM02 Manuel utilisateur

Bosch

Bosch BDU3740 Manuel utilisateur

Bosch

Bosch REXROTH AGK 20-80 Manuel utilisateur

Bosch

Bosch Active Line BDU310 Manuel utilisateur

Bosch

Bosch Rexroth EcoDrive Cs DKC-004 Series Manuel utilisateur

Bosch

Bosch Active Line Plus BDU 350: 0 275 007 047 Manuel utilisateur

Bosch

Bosch Rexroth IndraDrive CsDrive System with HCS01 Manuel technique

Bosch

Bosch Kiox 300 Manuel utilisateur

Bosch

Bosch BDU490P Manuel utilisateur

Bosch

Bosch Rexroth IndraDrive HMV01.1E-W0030 Manuel technique

Bosch

Bosch Rexroth ROTATRAC eGFT 8000 10 Series Manuel utilisateur

Bosch

Bosch REXROTH IndraDrive Instructions d'utilisation

Bosch

Bosch Rexroth Sytronix FcP 5020 Manuel utilisateur

Bosch

Bosch Rexroth Sytronix SvP 7020 PFC Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Fiche technique

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur