BOPIXEL OPR305 Series Manuel utilisateur
OPR305 Series DLP projector operating manual
Catalogue
一、Precautions for use .........................................................................................1
二、Module Hardware Features ................................................................................2
三、Connectors Description....................................................................................... 4
3.1 Connectors function .......................................................................................... 4
3.2 Pin function .......................................................................................................4
3.2.1 J1 ............................................................................................................. 4
3.2.2 J2 ............................................................................................................. 5
3.2.3 J3 ............................................................................................................. 5
3.2.4 J6 ............................................................................................................. 5
3.2.5 J7 ............................................................................................................. 6
3.2.6 J8 ............................................................................................................. 6
3.2.7 J9 ............................................................................................................. 6
3.2.8 J10 ........................................................................................................... 6
四、Operating Manual ................................................................................................7
4.1 Product description ........................................................................................... 7
4.2 software and documents ....................................................................................7
4.2.1 Software .................................................................................................. 7
4.2.2 Documents .............................................................................................. 7
4.3 software install .................................................................................................. 7
4.4 Operating instructions .......................................................................................9
4.4.1 drivers install ...........................................................................................9
4.4.2 connection of OPR305 series module .....................................................9
4.4.3 Lens adjustment and fixation .................................................................. 9
4.5 software Operating instructions ...................................................................... 10
4.5.1 pattern sets set up ..................................................................................10
4.5.2 add 1d pattern ........................................................................................11
4.5.3 pattern’s timing setting ..........................................................................12
4.5.4 pattern control ....................................................................................... 13
4.6 LED brightness adjustment .............................................................................14
4.6.1 LED switch ........................................................................................... 14
4.6.2 Light source current adjustment under 4A ........................................... 14
4.7 making batch file ............................................................................................ 17
4.8 Making firmware ............................................................................................ 22
五、Appendix .............................................................................................................26
5.1 DLP3010EVM-LC Firmware Release Notes ................................................. 26
5.2 "Internal Patterns" mode operation steps ........................................................27
5.3 How to Modify the Specifications of Test Patterns? ...................................... 33
六、FAQ ..................................................................................................................... 35
6.1 How to Program the DLPC3470 and DLPC3478? ......................................... 35
6.2 What is a 1D pattern? ......................................................................................35
6.3 Why would you want to use a 1D pattern? ..................................................... 36
6.4 What is a pattern set? ...................................................................................... 36
6.5 How many patterns can be stored in each pattern set? ................................... 36
6.6 How to change frame rate of internal pattern? ............................................... 37
6.7 Why is there a minimum pre-exposure dark time and post-exposure dark time
limit? ..................................................................................................................... 37
6.8 What actually happens in pre-exposure dark time and post-exposure dark time?
.............................................................................................................................. 37
6.9 What timings are supported by Internal pattern streaming mode? ................. 38
6.10 Do these minimum darkfield times have to be calculated?.......................... 38
七、Guarantee ........................................................................................................... 39
1
一、Precautions for use
Please read the manual thoroughly before use, misoperation may
cause damage to the DLP projector.
Attention
1. Optical module is fragile product, no dropping and disassembly is allowed.
2. Please power the optical module with 12V and higher than 4A power source.
3. Do not detach DMD FPC.
4. Please take anti-static measures before use
5. The optical module has only blue light source, do not enable red or green light
source.
6. Be aware of short circuit while wiring the optical module to other equipment.
7. This module will automatically power on when connected to power source.
Please contact us if not work properly.
8. Please read through the instructions before use. Misoperation may cause damage
to the module.
9. Please pay attention to anti-static measures before use. Static electricity will
cause damage to the main chip or DMD.
10. Before powering on, check whether there is overlap of the metal part of the IO
wire or foreign matter on the PCB board. The overlap of the bare IO wire or the
conductive foreign matter on the PCB board may cause a short circuit and cause
damage to the PCB board.
11. The power of the light source of this DLP projector is high.It is forbidden to
power on machine without connecting the radiator, the light source may burn out
within a few seconds.
Note: the GUI version used in this document is 2.2.0.6 and the operating system is
win10 x64.
2
二、Module Hardware Features
1. Resolution:1280x720
2. Max frame rate:2487Hz(1 bit),272Hz(8 bit)
3. Integrated 2M storage, store >1000 patterns in the flash memory.
4. Max power: 15W
5. Communication port:I2C(operation control),SPI(firmware programming),
USB(GUI connection)
6. Trigger voltage:5V default
7. 24-bit input pixel interface support: parallel or BT656, interface protocols.
8. Small dimension, a large aperture, optional Blue /RGB light source, extremely
high MTF and sharp image edges
9. Low distortion, distortion is less than 0.05%
10. Uniformity＞90%,Facilitate the use of grayscale coding pattern
11. Users customize optical performance for specific requirements
OPR305 series (DLP3010)
Type OPR305100 OPR305120 OPR305185 OPR305120S OPR305185S
Working
distance
mm
MI
N
TY
P
MA
X
MI
N
TY
P
MA
X
MI
N
TY
P
MA
X
MI
N
TY
P
MA
X
MI
N
TY
P
MA
X
90 100 115 60 120 280 30 185 700 65 120 145 85 185 540
Screen size
（TYP）
mm
24.3*13.7 60.4*34 136*77 Picture 1 Picture 2
Depth of
focus
mm
-2~+2 -15~+19 -55~+100 -5~+10 -30~+40
Throw
Ratio 4.12 1.99 1.36 1.99 1.36
Precision
um 19 47 106 47 106
Mode Orthographic projector Scheimpflug/Tilt structure
Dimension
mm 92*57*36 99*57*36 104*57*36 100*78*41 103*72*41
Distortion <0.05% <0.1%
Resolution 1280*720
Uniformity
JBMA >90%
Contrast 1000:1
Light source Blue LED（459nm）
3
Figure 1. OPR305 series top Figure 2. OPR305 series side
Figure 3. OPR305 series Scheimpflug top Figure 4. OPR305 series Scheimpflug side
Figure 5. OPR305120S Figure 6. OPR305185S
4
三、Connectors Description
If you need to connect OPR305 series module to MCU, you need to detach the
protection plate and connect J6 to your system. After the connection you need to
reinstall the protection plate before powering up.
You can find the connector number in the figure upside, and the red dot stands
for pin 1 of the connector.
3.1 Connectors function
Number Mates with part number Function
J1 MOLEX 43645-0200 Power source port
J2 MOLEX 51021-0400 USB for embedded
J3 USB TYPE C USB type C port
J6 AXT650124 Extend function port
J7 MOLEX 51021-0300 Fan port
J8 MOLEX 87439-0400 Power output
J9 MOLEX 51021-0600 Trigger output
J10 MOLEX 51021-0300 Trigger input
3.2 Pin function
3.2.1 J1
Pin num. Pin name Function
1 SYSPWR Power source 12V
2 GND Power source GND
5
3.2.2 J2
Pin num. Pin name Function
1 GND USB GND
2 DP DP
3 DN DN
4 VBUS USB power
3.2.3 J3
Mate with common use USB TYPE C cable
3.2.4 J6
Pin
num.
Pin name Function Pin
num.
Pin name Function
25 GND 26 GND
24 PDATA0 Video input 27 TRIG1_IN Trigger in
23 PDATA1 28 TRIG1_OUT Trigger out 1
22 PDATA2 29 TRIG2_OUT Trigger out 2
21 PDATA3 30 MCU_REQ Hand shaking
REQ
20 PDATA4 31 HOST_IRQ DLP state
19 PDATA5 32 RESETZ
18 PDATA6 33 MCU_ACK Hand shaking
ACK
17 PDATA7 34 PROJ_ON Power up signal
16 GND 35 PATTERN_READY Ready to
project
15 PDATA8 Video input 36 SPI0_CSZ0 SPI
14 PDATA9 37 SPI0_MISO
13 PDATA10 38 SPI0_MOSI
12 PDATA11 39 SPI0_CLK
11 PDATA12 40 I2C0_SDA I2C
10 PDATA13 41 I2C0_SCL
9 PDATA14 42 GND
8 PDATA15 43 PDM_CVS_TE Video input
7 GND 44 HSYNC_CS
6 PDATA16 Video input 45 VSYNC_WE
5 PDATA17 46 DATEN_CMD
4 PDATA18 47 PCLK
3 PDATA19 48 GND
2 PDATA20 49 PDATA23 Video input
1 PDATA21 50 PDATA22
6
3.2.5 J7
Pin num. Pin name Function
1 Fan power Fan power 12V
2 Fan lock detect Not used
3 GND Fan power GND
3.2.6 J8
Pin num. Pin name Function
1 3.3V output 3.3V 2A power out
2 5.0V output 5.0V 2A power out
3 12.0V output 12V 2A power out
4 GND Power GND
3.2.7 J9
Pin num. Pin name Function
1 Triger1 out VCC Trigger out voltage VCC
2 Triger1 output Trigger1 output
3 GND Trigger GND
4 Triger2 out VCC Trigger out voltage VCC
5 Triger2 output Trigger2 output
6 GND Trigger GND
3.2.8 J10
Pin num. Pin name Function
1 Triger1 in VCC Trigger in voltage VCC
2 Triger1 input Triger1 input
3 GND Trigger GND
7
四、Operating Manual
4.1 Product description
OPR305 series module are made for structured light projection, they can project
several 2D build in test patterns and programmable 1D 1bit or 8bit patterns.
Attention: OPR305 series module are different from TI DLP3010EVM-LC,
some functions of TI GUI will not be supported. The firmware of DLP3010EVM-LC
can not work on our system. Please use the firmwares from our website.
4.2 software and documents
4.2.1 Software
GUI:https://www.ti.com/tool/cn/DLPDLC-GUI
Firmware:
cus_5a_out12_in_run.img
cus_5a_out12_AutoRun.img
API:DLPC34XX-API
4.2.2 Documents
OPR305 系列 DLP 模块使用说明（本文档）
DLP Display and Light Control EVM GUI Tool User Guide (Rev. A)
DLP3010LC 0.3 720p 光控 DMD 数据表
DLPA3000 驱动器
DLPC34xx Controller API User's Guide
DLPC3470 and DLPC3478 Software Programmer's Guide
DLP3010 曝光时间参考表
4.3 software install
GUI install
8
图1
图2
图3
图4图5
图6
图7
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels BOPIXEL Projecteur
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
