Bonjear BJ-S825 Manuel utilisateur
Truck Tire Spreader
Instruction Manual
‘
WARNINGS
◆Please read the instruction booklet and all the directionslisted on the
sticker attached on the machine carefully andfully understand the contents
before use, which is necessary for protecting the users from harms and the
machine from damages.
◆This machine is used for spreading tires or repairing protective casing of
tires only. It can’t be used for other applications. Our company will not
accept any responsibilities for all the consequences due to improper use.
◆Keep the spreading hooks and claws clean in the process of spreading, to
avoid sliding due to grease or some other foreign objects, which will bring
danger to the maintenance work.
◆Please don’t use the machine when it obviously appears too old or when it
is clearly twisted out of shape or when it’s damaged, and make treatment in
accordance with the local laws and regulations of waste management.
◆The professionals that operate the machine should wear suitable
protective ocular coverings in a correct way throughout, to protect the eyes
from harms caused by the sundries in the process of repairing.
Product Illumination
Horizontal pneumatic car tire spreader special design for fixed the tires and
spreading the tires during repairing cars and small trucks, microbus, in order
to work for the tire polishing, cleaning and films affixed etc, equipped with
work light and tools rack to improve work efficiency, enable the tire repairing
work to be more convenient and faster. Manifest personalized design.
Technical Parameter
Be propitious to：
tire type：8.25-20/14.00-20(9R-16.5R);R22.5
Work Voltage:
Input voltage：220V 50／60HZ
Work light voltage：12V
Air pressure:: 8-10 KG/CM²
Product structure Illumination
(1) Tools Tray (2) pneumatic control box (3) tools racks
(4) Air Regulator Device (5) main body Power
(6) Pneumatic union (7) up &down pneumatic cylinder
(8) Short spread hook (9) Long spread hook
(10) Tire platform (11) Work light
(12) up &down platform (13) Adjusting valve
(14)Spread pneumatic cylinder (15) Tire lever
(16) Pneumatic tools union
(17)Spread pneumatic cylinder control valve
(18) Up &down pneumatic cylinder control valve
INSTALLATION
1. Place this product on solid ground and keep its flat
2. Remove the backboard of pneumatic control box from the inclined support
board
3. Take the fixed pin from the pneumatic control box
4. Put the pneumatic control box on the top of body box and adjust well the
position
5. Connect the tools tray with pneumatic control box well
6. Connect the tire sloping board with equipments well
7. Connect the spread hook which equipped with work light with equipments
well
8. Connect the short spread hook with equipments
9. Connect a fast joint top at 1/4 normal temperature and moderate air
pressure onto the fast joint top of the machine’s air inlet. The minimum
standard is to use 1/4 inch’s wind pipe every 100 square inches.
10. Fixed it on the flatly ground with screws and keep the screw firmness
Operation
1. Before start the machine, check carefully whether the fasteners on the
machine are loose or not because of transportation. If yesterday, must be
re-tightened.
2. Fix the tire on the tire spreader with claw by hand
3. According to the size of tire which need be repaired to adjust the
spreading claw to be the appropriate height. Place the spreading hook to be
link pin of the hanging device. Adjust the spreading hook, move the link pin
and spreading hook up and town in order to insert into one of adjusting holes
which totally have seven groups. Put the short spread hook inside the tire
and try to place the tire in the middle of tire lever if possible
4. Pull the spreading control
valve to the direction of spreading, and spread the tire to the width needed.
The tire will probably disengage from the spreader if the spreading hook arm
is too high. Operate after it is lowered and the height is properly adjusted.
5. Pull the up&down control valve to the direction of up&down needed,
raise the tire to a proper height.
6. If it’s needed to revolve the tire to a new position, please pull the
spreading control valve to the direction of contraction, revolve the tire to a
proper position on the machine after the spreading hooks are loosened, then
operate the machine.
7. The working light fixed on the machine needed to be adjusted to a proper
position, to illuminate the inside sufficiently and make the repair work easy.
8. After finished maintenance work, please firstly move the up&down control
valve to the downward direction, let the tire fall to the lowest, then move the
up&down control valve to the direction of contraction, loosen the spreading
hook and remove it from the tire core, then discharge the tire along the
sloping board.
Maintenance
◆Add the lubrication oil to the oil cup in time, always guarantee that the oil
quantity in the cup to be occupy 1/3-2/3 of the total volume. Adjust drip oil
speed, piston reciprocating run every 5 ~ 6 times for drip one blob oil for
standard. ensure the oil pathway lubricate fully.
◆clear away the dust and sundries always, check whether the fastener is
loose or not.
◆Drip oil to the piston rod and the various parts of pin regularly. Reducing
friction, extending machine life.
Table des matières
Manuels Épandeur populaires d'autres marques
Fisher
Fisher POLY-CASTER 78601 Manuel utilisateur
TurfEx
TurfEx RS7200 Manuel du propriétaire
Ferris
Ferris Pathfinder Series Manuel utilisateur
Fayat Group
Fayat Group DYNAPAC S100 Guide de dépannage
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Manuel d'installation et d'exploitation
EASTMAN
EASTMAN CR 500 Manuel utilisateur
