Boca Systems Mag 42 Manuel utilisateur
Users Manual
Mag 42 Ticket PrinterMag 42 Ticket Printer
BOCA SYSTEMS, INC.
©2000 Boca Systems, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part, without
the written consent of BOCA.
Every effort has been made to ensure that the information in this manual is accurate.
BOCA is not responsible for printing or clerical errors and reserves the right to change
specifications without notice.
Table of Contents Page
1.0 Introduction 1
2.0 Unpacking the Printer 2
3.0 A tour of your printer 3-5
4.0 Installation 6
5.0 Configuration 7
6.0. Standard Interface Pinouts 8
7.0 Thermal Paper - Theory and Specification 9
8.0 Maintenance and Adjustments 10-15
9.0 Magnetic Encoding - Theory and Specifications 16-19
10.0 Spare Parts 20
11.0 Troubleshooting Guide 21-22
Table of Figures and Appendices Page
Figure 1 Packaging 2
Figure 2 Mag 42 Ticket Printer 3
Figure 3a Mag 42 side view 4
Figure 3b Mag 42 side view - Electronics Exposed 4
Figure 4 Rear view 5
Figure 5 Ticket loading 6
Figure 6 Switches and Optical Devices 11
Figure 7 Print head removal 13
Appendix A Operator Menu options through control panel
FCC NOTICE
NOTE: The equipment has been tested and found to comply with the limits for a class
A digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radi-
ate radio frequency energy and , if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to insure compliance.
i
IMPORTANT NOTICE
THE PRINTER MUST BE OPERATED WITH THE COVER ON AND ALL
SCREWS ATTACHED. THE DATA CABLE MUST BE SHIELDED.
FAILURE TO OPERATE IN THIS MODE MAY CAUSE THE PRINTER TO
EMIT EMISSIONS IN EXCESS OF EITHER FCC OR CE REGULATIONS.
ADDITIONALLY, THE PRINTER MAY BECOME SUBJECT TO DAMAGE
BY EXCESSIVE ELECTROSTATIC DISCHARGES IF NOT OPERATED
IN THIS MANNER.
WARRANTY INFORMATION
PRINTERS - BOCA warrants each printer to be free of defects for a period of one year
from the date of shipment when subject to normal use and service. This warranty
covers all parts and labor except for the print head which is warranted for 90 days. All
warranty labor is to be performed at the BOCA facility. Equipment damaged by misuse
or negligence including damage to print heads caused by defective ticket stock is
excluded from this warranty.
Any defective equipment meeting these conditions should be returned to BOCA for
repair (freight prepaid) in its original box and packing material. A short note describing
the failure should be enclosed with the printer.
Equipment damaged in shipping should be reported immediately both to BOCA and to
the shipper.
EXTENDED WARRANTY PLAN - BOCA offers extended warranty plans for all printer
models. These plans cover all parts and labor. All labor is to be performed at the
BOCA facility. Equipment damaged by misuse or negligence including damage to print
heads caused by defective ticket stock is excluded from this extended warranty. The
customer, at his option, may request BOCA to ship individual parts to expedite simple
repair procedures. In certain cases where the customer is unable to wait for the nor-
mal repair cycle, BOCA will ship an exchange printer within one business day after
notification by the customer. All freight charges are the responsibility of the customer.
ii
1.0 Introduction
The BOCA Mag 42 is a direct thermal ticket printer with read-write magnetic capablility
and integrated bursting mechanism designed for ticketing environments which require
encoding and verification of data on a magnetic stripe. The printer is available in a
credit card (ISO 3 track) version. This manual will provide the user with general
information regarding printer set-up, configuration and troubleshooting. Please review
your programming guide for additional details.
1
2.0 Unpacking the Printer
The printer is shipped in a ruggedized container. Please save packing material for
future use. Remove the printer (see figure 1) and accessories from the box and
inspect for obvious damage. If damage is noticed, please report it immediately to
BOCA.
The following items should be in the box:
a) Ticket Printer
b) Hopper
c) AC power cord
d) Interface cable (optional)
2
Figure 1 - Packaging
3.0 A Tour ofYour Printer
Figure 2 - Mag 42 ticket printer
Hopper
Control Panel
LCD
3
Figure 3a - Mag 42 side view
Figure 3b - Mag 42 top view
Print Head Removed
Print Head
(shown removed)
Logic Board
4
Print Head
Toroid Transformer Board
I/0 Brd.
Magnetics Logic Brd.
Burster Solenoid
Burster Assembly
Stepper Motor (2)
Magnetics Module
(obscured)
Infeed Stepper Motor
Table des matières
Autres manuels Boca Systems Imprimante
Boca Systems
Boca Systems Mini MB Manuel utilisateur
Boca Systems
Boca Systems LEMUR -C Manuel utilisateur
Boca Systems
Boca Systems LEMUR-ERAM Manuel utilisateur
Boca Systems
Boca Systems FSP 44 Manuel utilisateur
Boca Systems
Boca Systems Lemur-C Manuel utilisateur
Boca Systems
Boca Systems Lemur-Z Manuel utilisateur
Boca Systems
Boca Systems LEMUR-X Manuel utilisateur
Boca Systems
Boca Systems Adjustable MC Ghost Manuel utilisateur
Boca Systems
Boca Systems Lemur Manuel utilisateur
Boca Systems
Boca Systems SUBATM Manuel utilisateur
Boca Systems
Boca Systems Micro Plus Manuel utilisateur
Boca Systems
Boca Systems Lemur-S Manuel utilisateur
Boca Systems
Boca Systems Lemur-C Manuel utilisateur
Boca Systems
Boca Systems Micro Manuel utilisateur
Boca Systems
Boca Systems Lemur Manuel utilisateur
Boca Systems
Boca Systems LEMUR-M Manuel utilisateur
Boca Systems
Boca Systems LEMUR-X Manuel utilisateur
Boca Systems
Boca Systems LEMUR-FDIO Manuel utilisateur
