Blusafe Origin Smart Manuel utilisateur
11
Please scan the QR to get newest
manuals on Blusafe Products
Blusafe
Origin Smart
Installation
v1.0
22
33
Origin Smart Handle
Battery Cover
Fingerprint Scanner
Proximity Reader
Wakeup Button and LED
Lever Handle
Louderspeaker Hole
Lever Handle
Thumb Turn
Setting Cover
44
0102030 40 50 60 70 80 90 100 1101020304050607080110 100 90120130140150
OPTION1:�Remove�the�handle,�measure�the�distance�from�the�spindle�centre�to�the�screw�holes�and�mark�on�the�tempIate
OPTION2:�Remove�the�handle,�place�the�template�on�the�door�with�the�spindle�holes�on�the�template
4954 44 39 34
INSERT INTO SLOT FULLY
TO SELECT BAR LENGTH
Box Contents
Key Card
Setting RulerSetting Tool
Mounting PlateInternal Handle External Handle
Fitting Jig
F
G
HL
K
J
A1A2B×4 C D
E
× 3
M N O
× 3 × 3
P001P001
Remove the Existing Handle & Cylinder
Put something in the bottom
of the door to prevent the door
closing and locking itself!
Remove the existing handles
and spindle. If a turn button
cylinder is fitted, remove
the internal handle with the
cylinder.
① Remove the existing
screws,there may be 2 or 3；
② Remove the internal handle;
③ Remove the external handle
and spindle to remove the
locking cylinder；
④ Remove the fixing screw and
turn the key/turn knob whilst
putting gentle pressure on
the opposite cylinderend,
until the cylinder starts to
withdraw. Pull the cylinder
out, if there is no movement,
try turning the key gently,
both ways, left and right.
Tip
• It may be necessary to
use a little force to fully
remove the cylinder if it is
catching on the sides of
the prep hole.
• Some cylinders will only
withdraw to the outside,
some only to the inside,
try both ways.
• If a security clamp is
fitted, it will be necessary
to remove this first, an
Allen key will be needed
to do this. Please see
the FAQ section on the
Blusafe website for help if
you are unsure.
Remove the Cylinder
• Ensure the door is unlocked before removing the handles. Do not close the door until
installation is complete.
Warning!
Remove the Existing Handle
04
04
01
01
01
02
03
03
P002P002
Install Operating Cam
Fix - Reset the cam
If the cam is accidentally turned, re-set it
to vertical by pushing down the brass pin
and turning the cam so the pin is in the
central position.
① Insert the setting tool into the operating cam.
② Push the operating cam into the lock (the hole in which you removed the key/cylinder).
③ Fix it in place with the fixing screw shown in the diagram.
④ Insert the fixing screw but do not overtighten.
⑤ Remove the setting tool.
L
Cam
K
J
Setting Tool
04
05
01
02
03
P003P003
Determine Handle Direction
Depending on which way your door opens, determine which way the handles need to face.
The handles should always point towards the door hinges. Check the Origin/Origin Smart handles
against the current handles.
If the handles need to face the other way, please see next page.
P004P004
Change Internal Handle Direction
If the internal handle direction is not correct, follow the below steps to adjust.
① Insert your screwdriver into the
inside of the handle as shown below.
Push it all the way to the end to
locate the screw.
② Unscrew the handle screw. Remove
it and the spring washer and discard
③ Remove the handle and rotate 180 degrees.
Use the new handle screw and spring washer
(D/E) to fasten the handle
Tip
• For external handle, simply
rotate the handle to the
required position before
inserting spindle.
D E
P005P005
Fitting the Screw Pillars
3 screw pillars are supplied,
but generally only 2 will be
required.
They can be added or removed
where necessary.
The pillars can slide up or
down when loosely tightened
to match the current holes.
Fitting the Screw Pillars
Method 1
Measure the screw holes of
the existing handle. Insert the
old spindle and use the setting
ruler supplied and fit the screw
pillars in the correct positions.
Alternative
Method 2
Use the old internal handle and spindle, join together with
the Origin/Origin Smart outer handle.
Fix the screw pillars loosely - in line with the old handle
screw ports.
Using the old handle screws, pass them through the old
handle into the screw pillars and turn to locate, then gently
tighten the pillars with fingers.
Remove the screws, old handle and spindle and fully tighten
the pillars with the setting tool.
Important!
• Ensure the bottom pillar
is below the electrical
contact wire.
Important!
• Ensure you fully tighten
the screw pillars with the
setting tool or at head
screwdriver.
OLD SPINDLE
Method 1
Setting Tool
Setting Ruler
P006P006
Please measure the total thickness of your
door. Select the spindle and fixing screw pack
as shown below.
Before fitting the handle assembly, please
ensure that the internal and external handle,
backplate, spindle and fixing screws are
removed from the packaging and within easy
reach.
Warning!
• Please make sure the main door lock is
in the unlocked position. If unsure, use
the old handle and spindle and push the
handle down before proceeding.
Door thickness
44-50mm
58-65mm
68-75mm
Measure Your Door Thickness
48mm×3
M·130mm
N·145mm
O·155mm
70mm×3
60mm×3
Autres manuels pour Origin Smart
1
Autres manuels Blusafe Serrure de porte
