BlueTrek Metal Manuel utilisateur
“Vol +”button
“Talk” button
“Vol -”button
English
1 I BLUETREK METAL
Before using your headset for the first time
-You must charge it continuously for about 4 hours, until the red indicator light turns off.
Please refer to the “Charging the BLUETREK METAL®”section of this manual.
-Pair the headset with a mobile phone. Please refer to the “Pairing the BLUETREK METAL®”
section of this manual.
Introduction
The BLUETREK METAL® headset is a wireless headset based on the Bluetooth® technology. It
complies with Bluetooth® 2.0 protocol, supporting Headset and Hands-free profile.
The BLUETREK METAL® headset has 3 buttons:
·“TALK” button (main button)
·“Vol +”button
·“Vol -”button
English
BLUETREK METAL I 2
Charging the BLUETREK METAL®
Please insert the adapter in the main body.Then connect the USB connector to a powered
USB slot.
During the charge, the red Bluetooth indicator is switched on. The indicator light will turn
off when the charge is complete.
During subsequent charges, the charging should take approximately 2 hours.
When you hear a low-tone beep in your headset at regular intervals, and the indicator light
flashes in red, your headset needs to be recharged.
123
In some cases, you have to charge by the USB cable.
4
English
3 I BLUETREK METAL
Important:
• If your headset is fully charged, the red indicator light will not turn on when plugging into
the charger.
• To maximize battery lifetime, it is recommended to recharge your headset to full capacity
only when the battery is low, since a battery has a lifetime of about 500 charging cycles.
• If you leave your headset battery empty for an extended period of time, it could excessively
discharge the battery. In this case, charge your headset for 2 hours or more until the battery
recovers and recharges completely.When you first charge the headset after prolonged stor-
age, it may take few minutes for the red indicator light to turn on.
• Do not charge your headset for more than 10 hours.
• The use of any other charger will automatically suspend the warranty. It is strictly forbidden
and can be very dangerous.
English
BLUETREK METAL I 4
Switching the BLUETREK® METAL ON and OFF
Switching BLUETREK® METAL ON
When your headset is off, press and hold the TALK button for about 3 seconds until the blue
indicator light is on. A beep (2 tones) can be heard in the speaker.
Release the TALK button.
Switching BLUETREK® METAL OFF
When your headset is on, press and hold the TALK button for about 7 seconds until the red
indicator light is on. A beep (2 tones) can be heard in the speaker then release the TALK
button.
Pairing the BLUETREK® METAL
Before using the BLUETREK® METAL headset, you must pair it with
your Bluetooth® mobile phone.
Pairing is the process of linking 2 Bluetooth® devices, so that they
can communicate.
To initiate pairing:
Place the BLUETREK® METAL and your mobile phone within 0.3
meter (1 foot) from each other.
Switch on your phone and select its Bluetooth® discover mode
(refer to the Bluetooth® mobile phone user manual).
1
2
Connect
Assign short name
Set as unauthorised
Delete
Select Cancel
“0000”
BLUETREK METAL
BLUETREK METAL
BLUETREK METAL
“Talk” button
English
5 I BLUETREK METAL
When the BLUETREK® METAL is switched off, press and
hold the TALK button for about 7 seconds until the indicator
light flashes red and blue alternately. And a sound can be
heard in the speaker.
3
If you haven’t started the discovery mode within 5 minutes, the headset will go to the standby
mode. You must then switch off your headset and start the pairing again.
If pairing was successful, the indicator light will switch to blue and flashes slowly.
The headset will connect automatically to the mobile phone.
Once the mobile phone detects the headset, a“BLUETREK METAL”message will be dis-
played. Follow the phone instructions to accept the pairing.The PIN code (or passkey) is 0000,
then press“yes”or“ok”.
For some phones, you may need to select“Connect”.
4
5
“Talk” button
English
BLUETREK METAL I 6
Making a call
Mobile phone with voice recognition
• Make sure the voice recognition function on your mobile is activated and your voice tags
have been recorded with the phone.To enter these, please refer to your phone’s manual
• When there is no incoming or active call, press once on the TALK button
• Wait for the audio signal sent by the mobile phone (generally a short tone).
• Speak the name of person you wish to call.
Mobile without voice recognition
• Make sure both the headset and the mobile phone are ON and in stand-by mode.
• Dial the number on the phone keypad, after approximately 2 seconds the audio connection
will be established.
Answering a call
When the headset rings, press once on the TALK button to take the call.
Ending a call
Press once on the TALK button to end an active call.
This function may not be available on some phones, please refer to the trouble shooting
frequent asked questions in our website: www.bluetrek.com. to find out more.
English
7 I BLUETREK METAL
Adjusting the volume
To increase the volume during an active call, press the“VOL+”button on the headset.
To decrease the volume during an active call, press the“VOL-“ button on the headset.
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ button for approximately 3 seconds. A periodic
tone can be heard in the speaker when the microphone is muted.
To end the mute function
When the microphone is muted, quickly press the VOL+ button once on the BLUETREK METAL.
The periodic tone will end.
Transferring a call from BLUETREK® METAL to the mobile phone
With a phone in Headset Profile
During an active call, to transfer it to the phone, simply turn off your headset.
With a phone in Hands-Free Profile
During an active call, to transfer it to the phone, press the TALK button for about 2 seconds.
English
BLUETREK METAL I 8
Transferring a call from the mobile phone to the BLUETREK® METAL
With a phone in Headset Profile
Switch on your headset.
With a phone in Hands-Free Profile
During an active call on the mobile phone, press the TALK button for about 2 seconds to
transfer the call.
This function may not be available depending on your phone.
Call waiting
When you hear a call waiting alert while you are on a call, press approx. 3 seconds on the
TALK button to accept the second call and place the current call on hold.
To switch between an active call and a hold call, press approx. 3 seconds on the TALK button.
To end the active call and take the hold call, press once on the TALK button.
This function may not be available, depending on your phone. However, you can always
answer the second call from your phone keypad.
English
9 I BLUETREK METAL
Wearing the BLUETREK® METAL
Two different sizes of ear hooks are included in the
pack to suit your ear size.
Fitting the Ergobud*
6 different sizes of Ergobud* are included in the pack to suit your ear size. You can
adjust the Ergobud position that you feel the most comfortable.
To replace the
Ergobud*, remove
the speaker cover by
pulling gently out
from the speaker.
Place the Ergobud*
back onto the speaker
by inserting the
bottom part first.
Autres manuels pour Metal
2
Table des matières
Autres manuels BlueTrek casque
BlueTrek
BlueTrek Sugar Manuel utilisateur
BlueTrek
BlueTrek MUSICALL Manuel utilisateur
BlueTrek
BlueTrek ORANGE Y2-2 Manuel utilisateur
BlueTrek
BlueTrek Tattoo Manuel utilisateur
BlueTrek
BlueTrek Tattoo Manuel utilisateur
BlueTrek
BlueTrek S21 Manuel utilisateur
BlueTrek
BlueTrek Metal Manuel utilisateur
BlueTrek
BlueTrek S21 Manuel utilisateur
BlueTrek
BlueTrek Mini Manuel utilisateur
BlueTrek
BlueTrek G3 Manuel utilisateur
BlueTrek
BlueTrek X3 Manuel utilisateur
BlueTrek
BlueTrek X3 PRO Manuel utilisateur
BlueTrek
BlueTrek M2 Manuel utilisateur
BlueTrek
BlueTrek G2 Manuel utilisateur
BlueTrek
BlueTrek E2 Manuel utilisateur
BlueTrek
BlueTrek Sense Guide de référence
BlueTrek
BlueTrek Bizz Manuel utilisateur
BlueTrek
BlueTrek Carbon Smart Manuel utilisateur
BlueTrek
BlueTrek X3 Manuel utilisateur
BlueTrek
BlueTrek Sugar-Clip Manuel utilisateur
