Blue-White SONIC-PRO MS6 Manuel utilisateur

Quick Start Guide

MS6

SONIC-PRO®Chemical Feed Flow Meter

IMPORTANT

Safety instructions

PRE-INSTALLATION

Before you begin

To access the wiring terminal, open the enclosure by

removing the four screws with the provided 3/16” hex

key. The meter must be powered by 5 volts DC. Wattage

must not exceed 5 watts. 20-24 AWG(American Wire

Guage) shielded cable is recommended for signal output

connections.

The MS6 wiring compartment is equipped with two

communications cable liquid-tight cable glad grommets for

cable diameters from .190 to .205 inches. Refer to page 21,

section 11 of the provided Operating Manual for details.

Planning

Mounts and supports must be sturdy enough to support the

plumbing and prevent vibration. Vibration and heavy loads

will damage the meter.

Wiring

In the Box

• MS6 Chemical feed ow meter

• Meter Body Connection Fittings

• 3/16” Hex Key

• Flash Drive(Operating Manual

and Blue-Central®)

• USB-A to USB-C Connector

• Power Supply(User congurable)

• Quick Start Guide

Tools Needed

1/32” Mesh strainer

Follow these instructions before installing your ow meter to avoid failure.

CAUTION

The MS6 is designed to be installed and operated by qualied personnel only.

Please note that warranty coverage does not inlcude damage due to misuse or

improper installation.

CAUTION

Always wear eye protection when installing or removing ow meters.

CAUTION

Conrm chemicals being used with MS6 ow meter are compatible with wetted

components of the ow meter.

CAUTION

Do not exceed maximum pressure. High pressure and temperature will damage

the meter.

PRESSURE

Maintenance

When the MS6 Flow meter is removed from the system

or an empty pipe condition causes the meter to dry out,

always ush the meter with water before reinstalling.

INSTALLATION

Step-By-Step

1Install Blue-Central®

Blue-Central® is Blue-White’s proprietary software application

that allows the user to update rmware and view the meter’s

device details. To congure the MS6, Blue-Central® must be

installed and running on a desktop or laptop computer. Insert

the provided USB Flash Drive, and open the .exe le to

install and run the Blue-Central® application.

Connect

Connect the meter to the desktop or laptop computer with the

provided USB to USB-C cable. The meter will appear on the

Blue-Central® dashboard (may take upto 30 seconds).

4Install in an upward direction

The ow meter must be installed in a vertical plane with uid

owing in an upward direction to ensure accuracy. To reduce

large particles and bubbles that can reduce signal quality, it is

recommended that a 1/32” mesh strainer is installed at the inlet

of the meter. Ensure all o-rings are in place and properly seated.

Congure

It is suggested that the user congures its operating

parameter in advance. The meter will work without performing

a conguaration, however, the default settings may not be

adequate for the required application. For assistance in

conguring the meter, refer to the provided Operating Manual

(page 7, section 6.0) located on the USB.

Digital drawdown

5Calibrate

After installation, and the MS-6 can be calibrated and ne-

tuned to provide the best accuracy for your dosing rate.

With solution running through the owmeter, re-connect

to the computer with Blue-Central®, and perform a Digital

Drawdown. Follow directions in Section 9.0 of the Operating

Manual for best results.

LIMITED WARRANTY

Your Blue-White product is a quality product and

is warranted for a specic time from the date

of purchase (proof of purchase is required).

The product will be repaired or replaced at our

discretion. Failure must have occurred due to a

defect in material or workmanship and not as a

result of the operation of the product other than

in normal operation as dened in the product

manual. Warranty status is determined by the

product’s serial label and the sales invoice or

receipt. The serial label must be on the product

and legible. The warranty status of the product

will be veried by Blue-White or a factory-

authorized service center.

MS6 are warranted for 5 years from the date of

purchase.

WHAT IS NOT COVERED

• Freight to the factory, or service center.

• Products that have been tampered with, or in

pieces.

• Damage resulting from misuse, carelessness

such as chemical spills on the enclosure,

abuse, lack of maintenance, or alteration which

is out of our control.

• Damage by faulty wiring, power surges, or acts

of nature.

• Damage that occurs as a result of:

meter misalignment, improper installation, over

tightening, use of non-recommended

chemicals, use of non-recommended adhesives

or pipe dopes, excessive heat or pressure,

or allowing the meter to support the weight of

related piping.

BLUE-WHITE does not assume responsibility for

any loss, damage, or expense directly or indirectly

related to or arising out of the use of its products.

Failure must have occurred due to a defect in

material or workmanship and not as a result of

the operation of the product other than in normal

operation as dened in the manual.

Warranty status is determined by the product’s

serial label and the sales invoice or receipt. The

serial label must be on the product and legible.

The warranty status will be veried by Blue-White

or a factory-authorized service center.

PROCEDURE FOR IN-WARRANTY REPAIR

Warranty service must be performed by the

factory or an authorized service center. Contact

the factory or local repair center to obtain a

RMA (Return MaterialAuthorization) number.

It is recommended to include a foot strainer

and injection/check valve tting since these

devices may be clogged and part of the problem.

Decontaminate, dry, and carefully pack the

product to be repaired. Please enclose a brief

description of the problem and proof of purchase.

Prepay all shipping and insurance costs. COD

shipments will not be accepted. Damage caused

by improper packaging is the responsibility of the

sender. When In-Warranty repair is completed,

the factory pays for return shipping to the dealer

or customer.

Have Questions?

+1 (714) 893-8529

[email protected] blue-white.com/contact-us

P.N. #80000-602 MS6 QSG REV 10 20220725

WARRANTY

Information

Autres manuels Blue-White Instrument de mesure

Blue-White

Blue-White F-461 Manuel utilisateur

Blue-White

Blue-White APNTU Manuel utilisateur

Blue-White

Blue-White ProSeries SONIC-PRO S4 Series Manuel utilisateur

Blue-White

Blue-White F-2000 Manuel utilisateur

Blue-White

Blue-White ProSeries CHEM-PRO C2F Series Manuel utilisateur

Blue-White

Blue-White F-400 Manuel utilisateur

Blue-White

Blue-White F-460 Manuel utilisateur

Blue-White

Blue-White APFCL Manuel utilisateur

Blue-White

Blue-White F-451 Series Mode d’emploi

Blue-White

Blue-White F-460 Series Manuel utilisateur

Blue-White

Blue-White F-1000 Manuel utilisateur

Blue-White

Blue-White F-460 Manuel utilisateur

Blue-White

Blue-White FLOWREAD R-300 Manuel utilisateur

Blue-White

Blue-White FLEX-PRO A3F Series Manuel utilisateur

Blue-White

Blue-White FLEXFLO A1 Series Manuel utilisateur

Blue-White

Blue-White F-430 Manuel utilisateur

Blue-White

Blue-White F-420 Series Manuel utilisateur

Blue-White

Blue-White ProSeries Sonic-Pro S1 Manuel utilisateur

Blue-White

Blue-White ProSeries-M MS-6 Series Manuel utilisateur

Blue-White

Blue-White F-1000 Manuel utilisateur

Blue-White

Blue-White MICRO-FLO Manuel utilisateur

Blue-White

Blue-White Sonic-Pro T-Track Manuel utilisateur

Blue-White

Blue-White D-300 Manuel utilisateur

Blue-White

Blue-White F-2000 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur