BLOTZ B06-CS-100 Manuel utilisateur

6mm 3x3 Tower Block Foyer

B06-CS-100

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Foyer (B06-CS-100)

Remove the front piece and its rear support from

the sprue.

Glue the support to the back of the piece using the

holes / lugs provided.

Now remove the rear wall and its rear support

from the sprue.

Glue the support to the back of the piece using the

holes/lugs provided.

Take the two side walls and glue them to the

front piece (with the doors towards the front of

the model). Then attach the rear wall. Allow the

model to dry.

Take the entrance piece from the sprue.

Flip the model upside down and insert the

entrance way piece. The four lugs on it should

slot into the holes provided.

Finally remove the eight decorative strips from the

sprue and attach them to the building using the

lugs/holes provided.

6mm 3x3 Tower Block Middle

B06-CS-150

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

Mid-Section (B06-CS-150)

Take two identical wall pieces and the two

support from the sprue. (check the lugs on the

sides of the walls to ensure they are the same).

Glue the one support to the back of each wall as

shown above. Leave them to dry.

Take the four ‘C’ shaped supports from the sprue

and glue each one to the bottom rear of each of

the four wall pieces as shown above. The arms of

the ‘C’ should fit between the lower windows

with the base of the ‘C’ protruding (see next pic)

Glue the four walls together as shown above. It is

easiest to do this if you have the building upside down

as shown. Leave to dry.

Take the twelve decorative strips from the sprue

and attach three to each side of the building as

shown above.

6mm 3x3 Tower Block oof

B06-MW-200

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due

care and remember to cut away from yourself at all times.

During the construction of this model you may find it convenient to use pegs / elastic bands to hold

pieces in place while you allow glue to dry.

oof Section (B06-CS-200)

Remove the four walls and ‘C’ supports from the

sprue. Glue the supports to the back of the walls

as shown above so that they protrude from the

lower edge of the wall.

Glue each wall piece in turn to the roof piece.

Finally glue one of the decorative strips to each

side of the building as shown above.

Table des matières

Autres manuels BLOTZ Jouet

BLOTZ

BLOTZ Old West Store 3 Manuel utilisateur

BLOTZ

BLOTZ B15-WW2-100 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-108 Manuel utilisateur

BLOTZ

BLOTZ B28-SF-229 Manuel utilisateur

BLOTZ

BLOTZ B28-AF-102 Manuel utilisateur

BLOTZ

BLOTZ 28mm Old West Store 4 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-114 Manuel utilisateur

BLOTZ

BLOTZ B20-ME-002 Manuel utilisateur

BLOTZ

BLOTZ B06-CS-003 Manuel utilisateur

BLOTZ

BLOTZ B20-DIDG Series Manuel utilisateur

BLOTZ

BLOTZ B10-ME-009 Manuel utilisateur

BLOTZ

BLOTZ B28-DA-008 Manuel utilisateur

BLOTZ

BLOTZ B10-CS-202 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-113 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-005 Manuel utilisateur

BLOTZ

BLOTZ B28-WW2-300 Manuel utilisateur

BLOTZ

BLOTZ B28-VSF-010 Manuel utilisateur

BLOTZ

BLOTZ B00-RT-229 Manuel utilisateur

BLOTZ

BLOTZ B28-ME-008 Manuel utilisateur

BLOTZ

BLOTZ B15-PS-004 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-110 Manuel utilisateur

BLOTZ

BLOTZ Old West Store 8 Manuel utilisateur

BLOTZ

BLOTZ B28-WW2-303 Manuel utilisateur

BLOTZ

BLOTZ 10mm Skyscraper Dice Tower Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur