BLOTZ Old West Store 3 Manuel utilisateur

28mm Old West Store #3

B28-OW-110

Assembly Instructions

Designed and made in the UK.

This is a model kit and is not intended for persons

under 14 years old.

Requires assembly. Supplied unpainted.

28mm Old West Front #1

B28-OW-400

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the two base pieces and the frame from the

sprue.

Glue the frame to the plank section, then glue the

other base section under it using the lugs to align

them.

Glue the rear plate into place.

While the assembly dries, place it against a rear

section to ensure it doesn’t tilt forwards.

Take the insert pieces from the sprue.

Glue these into the gaps in the framework.

Take the door and supports from the sprue.

Glue the lower support into place. Allow to dry.

Place the lower lug of the door into the lower support,

then sit the upper support onto the top lug before

gently easing it into place (see pic).

Apply some glue to the upper support and then slide

it completely into position.

The windows and sills.

Glue the sills into place at the bottom of the window

gaps.

Then glue the windows into place, along with the one

above the door.

Glue your desired sign and top bar in place.

The completed front.

28mm Old West Rear #1

B28-OW-500

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the two base pieces and the inner walls from

the sprue.

Glue the walls to the planked base so that all etched

detail Is facing inwards (see pic).

Note: Two lugs will extend through the floor.

Glue the base plate into position, using the lugs to

align it.

Take the frame pieces from the sprue.

Glue the end frame into place.

Then add the side frames. The thinner part of the

frame (with the sprue points on it) should be at the

bottom.

The insert panels for the sides.

Pop these into position.

The insert panels for the end.

Glue these into place.

Take the door and supports from the sprue.

Glue the lower support into place. Allow to dry.

Place the lower lug of the door into the lower

support, then sit the upper support onto the top lug

before gently easing it into place (see pic).

The window sills.

Glue a sill below each window.

The completed rear.

28mm Old West Roof #2

B28-OW-601

Please read these instructions fully before starting construction.

PVA or equivalent glue will be required to stick sections together.

Sand paper can be used to gently clean any joints.

A sharp modelling knife will be required to remove sections from the sprue. Please use knives with due care and remember

to cut away from yourself at all times.

During the construction of this model, you may find it convenient to use pegs / elastic bands to hold pieces in place while

you allow glue to dry.

Remove the pieces shown above from the sprue.

Glue the support bars through the holes in the roof

plate.

Glue the end pieces and ridge bar into place.

The end “frames”

The blank “frame”goes at the end nearest the support

bars. The open frame goes in the other end (see pic)

Add the insert pieces into the frame.

Glue the roof pieces into place.

The completed roof.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BLOTZ Jouet

BLOTZ

BLOTZ 10mm Skyscraper Dice Tower Manuel utilisateur

BLOTZ

BLOTZ B28-ME-010 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-112 Manuel utilisateur

BLOTZ

BLOTZ B20-ME-009 Manuel utilisateur

BLOTZ

BLOTZ B28-WW2-301 Manuel utilisateur

BLOTZ

BLOTZ B28-OW-113 Manuel utilisateur

BLOTZ

BLOTZ B20-ST-111 Instructions d'utilisation

BLOTZ

BLOTZ B28-STA-104 Manuel utilisateur

BLOTZ

BLOTZ B28-SF-226 Manuel utilisateur

BLOTZ

BLOTZ B10-RD-103 Manuel utilisateur

BLOTZ

BLOTZ B06-MW-100 Manuel utilisateur

BLOTZ

BLOTZ B15-CS-002 Manuel utilisateur

BLOTZ

BLOTZ B10-MW-001 Manuel utilisateur

BLOTZ

BLOTZ B00-ACC-400 Manuel utilisateur

BLOTZ

BLOTZ 28mm Old West Store 2 B28-OW-109 Manuel utilisateur

BLOTZ

BLOTZ B28-AF-102 Manuel utilisateur

BLOTZ

BLOTZ B20-MD-004 Manuel utilisateur

BLOTZ

BLOTZ B15-MW-007 Manuel utilisateur

BLOTZ

BLOTZ B06-CS-003 Manuel utilisateur

BLOTZ

BLOTZ Onaga Rocket Kohaya Manuel utilisateur

BLOTZ

BLOTZ B28-ME-004 Manuel utilisateur

BLOTZ

BLOTZ B15-ME-104 Manuel utilisateur

BLOTZ

BLOTZ B28-DA-008 Manuel utilisateur

BLOTZ

BLOTZ B28-WF-110 Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur