Blata Blatino Small Manuel utilisateur

USER’S MANUAL

SCOOTER WITH AUXILIARY ENGINE

SAFETY WARNING

Always pay attention to the instructions and safety warnings below

This manual contains important safety information and instructions which should be read

carefully before operating the vehicle. For your own safety and the safety of others follow

these rules.

Neither manufacturer nor distributor is responsible for injuries caused by unsafe and improper

use of the vehicle.

This vehicle is not allowed to be used on public roads!

Unsafe and careless use of the vehicle can result in serious injuries. The driver can

minimize the potential risks by wearing safety equipment. The driver must wear a

safety helmet, goggles, gloves, elbow pads, kneepads, and firm footwear. Avoid rough

surfaces and obstacles. Always drive with both hands on the handlebars.

Fuel and fuel vapour are highly toxic and flamable. Always be careful when handling

fuel – it can burn or poison you.

- stop the engine and turn off the fuel tap, keep naked flames and sparks away from

your bike.

- do not smoke near your bike.

- refuel only outdoors in a well ventilated space

- clean up any excess fuel immediately

- keep children and pets away

Always ride within the limits of vehicle/ rider and weather conditions to avoid

unnecessary accidents and injuries.

Check-ups

Shut the engine off when performing maintenance check-ups otherwise You could be

severely injured if your hands or clothing get caught by moving parts.

Make sure the engine and exhaust are cold before performing any inspection of this

machine

Riding with a chain in poor condition or improperly adjusted can lead to serious injury.

Always, Inspect, Adjust and Maintain the drive chain properly before each ride.

Failure to inspect and properly maintain the brakes increases the risk of having an

accident. Before each ride check the brake cables and the brakes efficiency.

Riding with worn brake pads can reduce the braking performance and cause an

accident. Check and replace brake pads according to the instructions in this manual.

Using worn, improperly inflated, or incorrect tyres will reduce stability and can cause

an accident.

DISPOSAL OF UNUSABLE PRODUCT

Unusable product become a waste and it’s desposal should be in accordance with

the law and any applicable local regulations. Don’t throw this product to municipal

waste.

Always inspect the bike before each ride (refer to the article ‘INSPECTION AND

MAINTENANCE’). Failure to inspect and maintain your bike properly increases the risk

of an accident or damage to the vehicle.

S C O O T E R – B L A T I N O Small

SERVICE MANUAL FOR USE AND MAINTENANCE

AND SPARE PARTS LIST

For your own safety and the safety of others obey the following

recommendations in order to use your SCOOTER in the most convenient and

correct way. Read the instructions very carefully and follow them before riding

the SCOOTER.

CONTENTS: PAGE

SAFETY .........................................................................................................................2

TECHNICAL DATA ........................................................................................................ 2

SETTING UP THE SCOOTER BEFORE A RIDE .......................................................... 3

ENGINE STARTING Fig. 1 ............................................................................................ 3

RIDING ........................................................................................................................... 4

SERVICE INSTRUCTIONS ............................................................................................ 4

BOLTS AND NUTS ........................................................................................................ 4

AIR FILTER .................................................................................................................... 4

CLUTCH .........................................................................................................................4

BRAKE ADJUSTMENT - Fig. 2..................................................................................... 5

REPLACEMENT OF BRAKE PADS ............................................................................. 5

CHAIN ADJUSTMENT AND SERVICE – Fig. 3 ............................................................ 6

TIRE PRESSURE ........................................................................................................... 6

STORAGE AND CUT OFF PERIOD .............................................................................. 6

SCOOTER BLATINO Fig. 4 ........................................................................................ 7,8

STRUCTURE OF ENGINE – Fig.5 ................................................................................ 9

CARBURETOR - Fig. 6 ............................................................................................... 10

FRONT AND REAR BRAKES - Fig. 7 ......................................................................... 11

LIST OF SPARE PARTS ........................................................................................ 12,13

GUARANTEE LIST ....................................................................................................... 14

ACCESSORIES ............................................................................................................ 15

SAFETY

This vehicle does not conform to Federal Motor Vehicle Safety Standards and

is not intended for operation on public streets, roads or highways. Serious

injuries can result from the unsafe operation of this vehicle. Wearing the safety

equipment can prevent the assumed risks and injuries. Safety helmet, goggles,

elbow pads, kneepads, gloves and appropriate shoes must be worn. Do not

drive this vehicle in traffic, or on wet, frozen or oily surfaces. Avoid uneven

surfaces and obstacles. Drive with two hands on the handlebars.

TECHNICAL DATA

ENGINE: TWO STROKE ...............................................................AIR COOLED

CYLINDER CAPACITY ......................................................... 27.00 cc

MAX. POWER .....................................................1,4 kW at 7800 rpm

MAX. TORQUE ................................................. 1,92 Nm at 6600 rpm

IGNITION.......................................................................ELECTRONIC

CARBURETOR .......................................WALBRO with diaphragm

STARTING ............................................................................MANUAL

CLUTCH...................................................CENTRIFUGAL, FRICTION

TRANSMISSION ........................ BY CHAIN ON THE REAR WHEEL

FRAME: WELDED .................................OF HIGH-STRENGHT STEEL TUBES

HANDLEBAR...................................... OF DURALUMIN, FOLDABLE

BODY: ..……………………… ………FIBERGLASS REINFORCED PLASTIC

WITH ANTIVIBRATION MASS AND ANTISLIP SURFACE

BRAKES: FRONT WHEEL ................................. MECHANICAL DISC BRAKES

REAR WHEEL ................................... MECHANICAL DISC BRAKES

WHEELS: FRONT RIMS .............................................. OF LIGHT ALLOY 4”- 51

REAR RIMS. ............................................... OF LIGHT ALLOY 4”-51

TIRE SIZE: FRONT ................................................................................... 2.80 - 4”

REAR ..................................................................................... 2.80 - 4”

FUEL: ………………MIXTURE OF PETROL 91 OR HIGHER OCTANE +

2 STROKE SYNTHETIC OIL IN THE RATIO 50:1

FUEL TANK CAPACITY ..........................................1,4 L = 0,369 gal.

FUEL CONSUMPTION ....................cca 1l / 40 km = 0,01 gal/ 1 mile

SPEED: ...........................................................................35 km/ h = 21,7 MPH

MAX. LOAD: .. ................................................................................... 90kg = 198 Lb

WEIGHT: ..................................................................................... 15,5kg = 34Lb

BASIC DIMENSIONS:

LENGHT......................................................................34,5” (875 mm)

WIDTH.........................................................................16,5” (418 mm)

HEIGHT .......................................................................37,0” (940 mm)

FOLDED HEIGHT .......................................................17,7” (450 mm)

SETTING UP THE SCOOTER BEFORE A RIDE

Make sure that all of the bolts and nuts are properly tightened, especially

before the first ride. The SCOOTER is easily portable when the handlebars are

in the folded position and locked with pin.

To put the SCOOTER into the drive position:

- unlock the handlebar pin and place the handlebars in the vertical

position

- lock the handlebars with movable tube in down direction up to lower

handlebars

To put the SCOOTER into the drive position with seat kit (follow step 1 and 2)

plus insert the seat tube into the seat hole in rear fender so the tube is in the

holder and is protected against mechanical movement. The seat is adjustable

by unscrewing the attachment collar.

Fill the tank with fuel mixture, which should be a mixture of petrol 91 or higher

Octane and 2-stroke synthetic oil in a ratio of 50:1 (for break-in 30:1). The

period of break-in is until usage of 1.5 gallon of fuel mixture. Mix the petrol and

oil very throughly before putting it into the fuel tank. Always turn off the

engine to re-fuel it. Keep away from open flames.

ENGINE STARTING

A – primer fuel button

B – starter button (starter carburetor)

C – fuel outlet

D – idling speed adjusting screw

E – max. revolutions adjusting screw

Fig. 1

Instructions for starting up the engine:

- Approach the SCOOTER from the left side (in the forward direction)

- Hold twistgrip with left hand

- Press down on deckboard with left foot

- Hold pull-start with right hand

Starting up a cold engine: only slightly, or not at all open twistgrip. Press 5 to 6

times button “A” until the fuel runs through the fuel outlet “C” without bubbles.

Press black button “B” once.

Firmly pull 1 to 4 times the pull-start (never pull the pull-start all the way out). If

the engine does not start repeat the operations. When the engine starts up, let

it run for about a minute before riding.

Starting up a warm engine: the above-mentioned operations are not necessary,

just pull the pull-start to start the engine. If it is necessary rotate the twistgrip.

During the break-in period do not use the full power of the engine. We do not

recommend running the engine in max. revolutions without any load.

RIDING

After starting up the engine place one foot on the deck board and slightly

rotate the twistgrip. In the moment when the SCOOTER begins to move forward

place the other foot on the deck board, too. To stop or slow down rotate the

gas lever backward and slow down, following these steps –

- pull with left hand the rear brake leverto slow down or stop

- slightly pull with right hand the front brake only to slow down

Do not brake abruptly with front brake as it can cause a CRASH (the brakes are

very effective). Pressing the red button on the handlebars shuts down the

engine.

To keep the SCOOTER quiet and safe do not drive with wide open throttle.

Reasonable operations with the throttle lower the fuel consumption and

noisiness without much speed reduction. Drive safely and always hold the

handlebars with both hands .

SERVICE INSTRUCTIONS

The following service instructions should be performed periodically to keep the

SCOOTER in fail-safe conditions.

Bolts and Nuts:

The bolts and nuts must be checked and tightened up again after every 25

hours of running time.

Air Filter:

The air filter must be checked and cleaned if needed after every 50 hours of

running time. If the SCOOTER is used in a dusty environment the air filter

must be checked and cleaned more often.

Instructions for dismantling the air filter:

The backside of the air filter can be dismantled after unlocking the interlock

placed at the topside of the filter. Take out the filter elements and check for

contamination. Contaminated filter elements should be carefully washed with

detergent and dried thoroughly. The re-installation is made in the reverse order

of the dismantling instructions.

Clutch:

The thickness of the clutch-lining shoe must be checked after every 100 hours

of driving. The thickness cannot be less than 1 mm (0,039 in). The engine must

be removed from the frame during the clutch control.

Instructions for dismantling the engine:

The first step is to dismantle the fuel tank and disconnect the fuel pipes.

Disconnect the gas cable from the carburetor and unscrew the four bolts on

the clutch housing. The engine must be removed in the direction away from the

clutch housing. The clutch housing will remain on the frame. Second step is

the control of the clutch lining – the thickness cannot be less than 1 mm (0,039

in). In case the jaws (shoe) of the clutch must be changed the clutch spring

must be changed, too.

The installation is made in the reverse order of the dismantling instructions.

Check the connections of the fuel pipes to the carburetor.

ADJUSTING THE BRAKES

Small incremental brake adjustment :

Free play at the handlebar lever is

effected by turning the knurled end on the

cable adjustor. This will allow the lever to

be set at the nominal to ¼ inch of free

lever movement.

Basic brake adjusting:

Screw in the knurled cable adjustor at the

brake lever so the cable is in it’s most

slack starting position.. At the caliper,

loosen the nut, No. 3 and tighten the

adjustable bolt No. 4, so the wheel cannot

turn. Back off bolt No. 4 about ¼ to ½ of a

turn and fix it with lock nut No. 3. Do not

use the cable retainer No. 5 for adjusting

the brakes!

BRAKE PADS REPLACEMENT: FIG.7

At first, screw in the knurled cable adjustor at the brake lever on the

handlebars. Unscrew two screws M5-914.003.01 that hold the brake body on

fork and shift out the brake backwards. Take out from brake body two distance

columns and two columns with coil. Do not loosen the cable retainer! Unscrew

screws M6-914.010.01 and separate both halves of brake body and shift the

worn-out brake plates out. Into the part with operating mechanism slide the

brake plate with pin bore and unscrew completely the adjusting screw. Force

on carefully the brake plate into the opposite piece. Before reassembly clean

the whole brake. Assembly follows in reverse sequence.

Carburettor:

After the engine has been run in, sometimes the carburettor has to be adjusted.

We suggest you have this operation done by a qualified service shop. For

those who believe they are able to do it themselves, this is the procedure you

must follow:

The setting is done with the rear wheel lifted and the engine running. Let the

engine run at full speed by turning the gas grip and then by turning the

adjusting screw (Fig. 1 – adjusting screw “E”). Set (tune) the engine to the

highest possible speed and then turn the gas grip back.

Set idling speed to between 3000 and 3100 rpm by turning screw “D” – see Fig.

1. The carburettor is a very fine piece of equipment and must be kept clean.

Service and Chain Adjusting:

The chain adjustment can be seen on the Fig. 3. Unscrewing three bolts M 6 –

914.007.01, which hold the engine to the frame from the bottom side of the

SCOOTER, and moving the engine into the front can increase the chain

tension. Check if the pinion is not orientated against the chain. When the chain

is adjusted for 5 mm (1/4 inch) play tighten up the bolts.

Regular lubrication of the chain increases its lifetime and protects from

noisiness. It is necessary to lubricate the chain after every engine wash or ride

in the rain. It is recommended to use special spray oil for chains.

Fig. 3

Tire Pressure:

The general tire pressure depends on the weight of a driver and the character

of the road. The average pressure is between 160 – 210 kPa (23 – 30 PSI). The

higher rates are recommended for heavier drivers and the smoothest roads.

STORAGE AND CUT OFF PERIOD

For the storage period the fuel evaporation will occur. The fuel evaporation can

cause malfunction of membrane pump. For this reason it is necessary once a

month to refill the fuel into the fuel tank and pump it with the button “A” (Fig. 1)

into the carburetor and /or restart the engine, too.

The SCOOTER must be stored in a dry place and protected from dust.

5 mm

FIG. 4

Ce manuel convient aux modèles suivants

Table des matières

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur