Black Hawk Automotive BH7210 Instructions d'utilisation
Model Capacity
BH7011
1/2 Ton
BH7210 1 Ton
Hydraulic Transmission Jacks
Operating Instructions & Parts Manual
Blackhawk Automotive is a Licensed Trade Mark Made by SFA Companies, Kansas City, MO
Made in PRC
BH7011-M0_082018
SFA Companies
10939 N. Pomona Ave. Kansas City, MO 64153
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
!ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes
de utilizar el aparato.
• El manual de instrucciónes y la información de
seguridad deben estar comunicado en lengua del
operador antes del uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
!WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. Immediately transfer the load to
an appropriate work station.
WARNING: Cancer and Reproductive Harm.
AVERTISSEMENT: Cancer et dommages au système reproducteu
r.
ADVERTENCIA: Cáncer y daño reproductivo.
www.P65Warnings.ca.gov
2
Saddle
Handle
Release Valve Knob
Lift Arm
Tilt Adjustment Knob
Caster
Chain
Handle Sleeve
*Oil Filler Plug (not shown)
(*) on the hydraulic unit,
below the lift arm
Figure 1- Typical Transmission Jack Components BH7210 shown)
SAFETY and GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack
before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating
procedures before attempting to use. The owner and operator shall be aware that use and repair of this product
may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's
native language before use of this jack is authorized. If any doubt exists as to the safe and proper use of this jack,
remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or damaged parts are noted. Any jack that appears
damaged in any way, or operates abnormally shall be removed from service immediately. If the jack has been or
suspected to have been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately
discontinue use until jack has been checked by a factory authorized service center (contact distributor or manufacturer
for list of authorized service centers). It is recommended that an annual inspection be done by qualied personnel.
Labels and Operator's Manuals are available from manufacturer.
PRODUCT DESCRIPTION
Blackhawk Automotive Hydraulic Transmission Jack is designed to be used as an aid in the removal and installation
of automotive and light truck transmissions, transfer cases and transaxles. This jack is for use under portable lift
equipment, where vehicle must be supported by a pair of appropriately rated jack stands.
NEVER use for any purpose other than those uses outlined above!
!
3
PREPARATION
Assembly
The angles and chains are pre-assembled on the angle bar.
Install the angle bar assembly onto the saddle plate.
model BH7011 (see Fig 2):
Tools required: 16mm wrench.
1. Remove the M10 nuts & lock washers (A) from the of angle
bar.
2.
Place the angle bar to on slot of the saddle plate (B)
, adjust
to desired position then tighten the nut & lock washer (A).
3. Repeat for the other angle bar.
model BH7210 (see Fig 3):
Tools required: 18 mm wrench.
1. Remove the M12x35 bolt, washers & nut
(C & D)
from the
angle bar.
2. Place and align the angle bar to one slot of the saddle
plate.
3. Insert at washer & bolt
(C) through the angle bar hole and
saddle plate slot (E). Adjust to desired position then tighten
with nut and lock washer (D).
4. Repeat for the other angle bar.
Fig. 2
Fig. 3
(A)
Saddle
Plate
Angle
Angle Bar
Screw Hook
(B)
(D)
Saddle Plate
Angle
Angle Bar
L-Hook
(E)
(C)
Shackle
Before Use
1.
Verify that the product and application are compatible, if in doubt call Blackhawk Automotive technical service
(816) 891-6390.
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve knob (see Fig 1):
a. Clockwise until rm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the saddle plate.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the saddle plate.
4. With saddle fully lowered, remove the oil ller plug. Pump 6 to 8 full strokes. This will help release any pressurized
air which may be trapped within the reservoir. Check oil level. Proper oil level will vary from just covering the ram
cylinder to 3/16” above it as seen from the oil ller hole. Reinstall the oil ller plug.
5. Ensure that jack rolls freely. Raise and lower the unloaded jack throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with Blackhawk
authorized replacement parts only.
Bleeding / Venting Trapped Air
With the release valve in the OPEN position (3b.) and with saddle fully lowered, locate and remove the oil ller
plug. Pump 6 to 8 full strokes. This will help release any pressurized air which may be trapped within the reservoir.
Reinstall the oil ller plug.
4
To avoid crushing and related injuries:
•
Never work on, under or around a load supported only by hydraulic jack.
• Be alert and sober when using this product. Do not operate under the
inuence of drugs or alcohol.
!WARNING
!WARNING
•Read, understand, and follow all printed material provided with and on this product before use.
• Do not exceed rated capacity.
• Use only on hard, level surfaces.
•Adequately support the vehicle before starting repairs.
• If loaded jack must be moved, make certain that load is secured by appropriate means, is stable, is in
the lowest possible position, is moved over a smooth, hard level surface and that the lifting platform
is level.
• Use of this product is limited to removal, installation, and transportation of automotive and light
truck transmissions, transfer cases and transaxles.
• Use only adapters / accessories provided by the manufacturer of this transmission jack.
• Use only adapters / accessories whose rated capacity is greater than the rated capacity of this jack.
• Ensure the center of gravity is center loaded on the saddle.
• Never use this device as a work/repair station. Transfer the load immediately to a suitable work station.
• No alteration shall be made to this product.
• Failure to heed these markings may result in personal injury and/or property damage.
5
SPECIFICATIONS
OPERATION
Follow the instruction for removal and installation of transmission, transfer case or transaxle according to the
vehicle manufacturer's service man
Raise saddle assembly:
1. Close release valve by turning release valve knob clockwise rmly.
2. Insert handle into handle sleeve, then pump handle until the load is contacted.
3. Secure load with provided chains.
Ensure center gravity of load is centered on the saddle and load is stable before moving jack. An o-center
transmission could cause the jack to tip or ip over .
Lower saddle:
Be sure all tools and personnel are clear before
lowering load. Slowly open the release valve! The more
you turn the knob counter-clockwise, the faster the load will come down. Maintain control of the rate of
speed at which the load lowers at all times!
1. Secure load to the jack with provided chain.
2. Slowly, gently turn the release valve knob counter-clockwise, never more than 1/2 full turn until the load is
completely lowered.
3. Immediately transfer the load to an appropriate work station.
4. After removing load from the jack, ensure that saddle is fully lowered to reduce ram exposure to rust and
contamination.
Never use this jack as a workstation!
!
!
!
Model Capacity Min.
Height
Max.
Height Saddle Base Extended Saddle
Area Jack Size Volume of
Hyd. Oil
BH7011 1100 lb 8 1/2" 24 3/4" 12 5/8" x 7 7/8" 17" x 9 3/8"
31" x 15"
85 mL
BH7210 2000 lb 7 7/8" 33 1/2" 14 1/4" x 7 7/8" 17" x 15 1/2"
40 3/8" x 19 1/8"
155 mL
MAINTENANCE
Important: Use only good grade hydraulic jack oil. Avoid mixing dierent types of uid and NEVER use brake uid,
turbine oil, transmission uid, motor oil or glycerin. Improper uid can cause premature failure of the jack and the
potential for sudden and immediate loss of load. We recommend Hein-Werner HW93291 or equivalent hydraulic
jack oil.
Adding oil
1. With saddle fully lowered set jack in its upright, level position. Locate and remove oil ller plug.
2. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall oil ller plug.
Changing oil
For best performance and longest life, replace the complete uid supply at least once per year.
1. With saddle fully lowered, remove oil ller plug.
2. Lay the jack on its side and drain the uid into a suitable container.
Note. Dispose of hydraulic uid in accordance with local regulations.
3. Set jack in its level position. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall
oil ller plug
.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
casters and pump assemblies move freely.
Cleaning
Periodically check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily
cloth.
Note: Never use sandpaper or abrasive material on these surfaces!
Storage
When not in use, store the jack with saddle fully lowered.
6
TROUBLESHOOTING
7
Symptom Possible Causes Corrective Action
Jack will not lift load • Release valve not tightly closed
• Load is too heavy
• Ensure release valve tightly closed
•Consider higher capacity jack
Jack will lift, but not maintain
pressure
•Release valve not tightly closed
•Hydraulic unit malfunction
•Ensure release valve tightly closed
•Discontinue use, Contact
Blackhawk Tech. Service
Jack will not lower after unloading • Reservoir overlled
• Linkage binding
• Ensure load is removed, then drain
uid to proper level
• Clean and lubricate moving parts
Poor lift performance • Fluid level low
•Air trapped in system
• Ensure proper uid level
•With ram fully retracted, remove
oil ller plug to let pressurized air
escape, reinstall oil ller plug
Jack will not lift to full extension • Fluid level low • Ensure proper uid level
8
Figure 4 - Replacement Parts Illustration for Model BH7011
A
2
B
CD
EFGH
I
J1
4
3
6
578
9
10 11
12
14
15
16
17 22
18
19
20
13
21
23
25
24
REPLACEMENT PARTS
(refer to page 8 thru 11)
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, give Model number, serial number and parts description.
Call or write for current pricing: SFA Companies, 10939 N. Pomona Ave. Kansas City, MO 64153, U.S.A.
Tel: (816) 891-6390 Fax: (816) 891-6599 E-Mail: [email protected]
Replacement Parts Illustration for Model BH7011
9
Item Part No. Description Qty.
1 4500-01000-000 Hydraulic Unit 1
2 5905-00100-100 Filler Plug 1
3 5905-00091-000 Oil Seal 1
4 4500-90009-K03 Release Valve 1
5 4500-01004-000 Pump Cylinder 1
6 4500-01301-000 Pump Piston 1
7 5403-10038-000 Pin 1
8 5403-08038-000 Pin 1
9 4500-01008-000 Handle Sleeve 1
10 B020-10003-000 Filter 1
11 4500-00004-000 Pivot Pin, Hyd Unit 2
12 4500-02000-000 Handle Assembly 1
13 BL80-20002-000 Handle Grip 1
14 4500-90009-K02 Caster Assembly 4
15 4500-03000-000 Saddle Assembly 1
16 4500-03300-000 Angle Bar 2
17 4500-03100-000 Angle I 2
18 4500-03200-000 Angle II 2
19 4500-03001-000 Screw Hook 2
20 5207-00006-000 Wing Nut, M6 2
21 5207-00010-000 Wing Nut, M10 4
22 4500-03002-000 Chain 1
23 5202-00010-000 Nut 4
24 4500-03600-000 Tilt Screw 1
25 5202-00012-001 Nut, M12 1
* 45000S-071 Seal Kit, Hyd Unit -
(*) Seal Kit Contents:
Item Description Qty.
2 Filler Plug 1
3 Oil Seal 1
A O-ring 1
B O-ring 1
C Back-up Ring 1
DU-cup 1
EBack-up Ring 1
F O-ring 1
G Back-up Ring 1
H O-ring 1
I Seal 1
J O-ring 1
Replacement Parts List for Model BH7011
10
Replacement Parts Illustration for Model BH7210
C
B
A
D
E
F
G
H
I
J
K
L
M
N
O
1
2
3
4
5
6
7
9
8
10
11
12
13
14
15
16
17
18
19
20
22
21 11
23
24 25
26
26
29
27
28
30
31
27
28
32
34
33
Figure 5 - Replacement Parts Illustration for Model BH7210
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Black Hawk Automotive Jack
Black Hawk Automotive
Black Hawk Automotive BH2300 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH7000 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive Magic Lift BH6057 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH5010B Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6011 Manuel de service
Black Hawk Automotive
Black Hawk Automotive Banner B630 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH2500 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6036 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6023 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH5120B Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH2020B Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6011 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH2128 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive PLATINUM BP225 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6034B Manuel utilisateur
Black Hawk Automotive
Black Hawk Automotive BH7450 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6222 Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH700B Instructions d'utilisation
Black Hawk Automotive
Black Hawk Automotive BH6221 Instructions d'utilisation
Manuels Jack populaires d'autres marques
VEVOR
VEVOR TJD-12000SP-F Manuel utilisateur
ULTIMATE SPEED
ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur
Stels
Stels 51131 Manuel utilisateur
Bushranger
Bushranger RJX01 Manuel utilisateur
Clarke
Clarke CTJ2500QLG Manuel d'installation et d'exploitation
Valex
Valex 1650520 Manuel utilisateur
