Black Box SW178A Manuel utilisateur
SEPTEMBER 1998
SW178A
SW179A
Compact Bidirectional
Dual Bus Autoswitches
2 to 2
4 to 2
CUSTOMER SUPPORT INFORMATION
Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX
FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
1
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
TRADEMARKS USED IN THIS MANUAL
Centronics is a registered trademark of GENICOM
Corporation.
DeskJet is a registered trademark of Hewlett-Packard.
Zip is a registered trademark of Iomega Corporation.
Windows NT is a trademark, and Windows is a registered
trademark, of Microsoft Corporation.
Any trademarks mentioned in this manual are acknowledged
to be the property of the trademark owners.
2
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with the
manufacturer’s instructions, may cause interference to radio communication. It
has been tested and found to comply with the limits for a Class A computing
device in accordance with the specifications in Subpart J of Part 15 of FCC rules,
which are designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment. Operation of
this equipment in a residential area is likely to cause interference, in which case
the user at his own expense will be required to take whatever measures may be
necessary to correct the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
3
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones
de operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,
cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,
etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales
que sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más
allá a lo descrito en las instrucciones de operación. Todo otro servicio
deberá ser referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama,
sofá, alfombra o superficie similar puede bloquea la ventilación, no se
debe colocar en libreros o gabinetes que impidan el flujo de aire por los
orificios de ventilación.
4
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo
del tipo descrito en el instructivo de operación, o como se indique
en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la
polarización del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que
no sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen
del aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo
a las recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos
de las lineas de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo
no sea usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos
no sean derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro
del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra
un cambio en su desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
5
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
1. Specifications
SW178A SW179A
Autoswitch Device Output Ports 2 2
Autoswitch Computer Input Ports 2 4
Cable Type Required
Computer to Autoswitch DB25 M/M
Device to Autoswitch DB25 M/Centronics®36 M
Maximum Cable Distance 5 meters
Maximum Transfer Rate 2 megabytes/second
Number of Device LEDs 2
Computer Input Port LEDs 4
Input/Output Port Selection Auto/manual
Timeout Selection 5, 10, 20, or 40 seconds
File Transfer A, B A–B, C–D
Software DOS; Windows 3.1, 95, 98;
Windows NT
Size SW178A: 7"H x 3.7"W x 1.1"W
(17.9 x 9.3 x 2.7 cm);
SW179A: 7.3"H x 3.7"W x 1.1"W
(18.5 x 9.3 x 2.7 cm)
Weight 7 oz. (200 g) 8.5 oz. (240 g)
Operating Temperature 41 to 104°F (5 to 40°C)
Optional Power Adapter 9 VDC, 500 mA
Certification FCC, CE
6
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
2. Introduction
2.1 Description
The IEEE 1284 standard interface is found on most
printers today. It enables bidirectional communication
between the PC and the printer, allowing the printer to
send information back to the host PC using its built-in
microprocessor.
The Compact Bidirectional Dual Bus Autoswitch
supports full compatibility with IEEE 1284, including
Centronics, nibble, special nibble, byte, Enhanced
Parallel Port (EPP), and Extended Capabilities Port
(ECP). The dual-bus design allows simultaneous access
of both devices to the attached computer. It also
features manual and auto channel-port selection, and
works with DOS, Windows 3.1, Windows 95, Windows 98,
and Windows NT.
The Autoswitch supports IEEE 1284 parallel devices
such as Zip®drives, scanners, CD-ROMs, back-up tapes,
digital CCD cameras, external hard drives, and Ethernet
adapters.
7
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
2.2 Function Descriptions
2.2.1 A
UTO
-L
INK
M
ODE
When powering the Autoswitch, you will see the LEDs of
the Computer Input Port circularly scanned from LED A
to D. The Printer Output Port LEDs will remain lit. Your
Autoswitch constantly scans its computer input ports,
looking for a job to send to one of its output ports. You
will see the input ports’ LEDs blink in sequence as the
switch goes through its scan cycle.
Device Out Ports LED Indicator:
PA & PB LED Remain Lit Auto-Link Mode
PA & PB LED are Lit OFF File Transfer Mode
2.2.2 M
ANUAL
M
ODE
The Switch has two input push buttons labeled Device
and Computer. When you power on the switch, the
switch is in Auto-Link Mode. After you press the
Computer button, it is in manual-setting mode. Press the
Computer button several times and you will see the
LEDs light in order as the active selection moves from
AutoScan to LED A, B, C, and D. Stop pressing the
button when the LED lights for the computer input port
8
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
you want to set up. You can press the Printer button
several times to cycle through the three level of available
choices (PA, PB, or File Transfer). Finish the cycle to go
back to Auto-Link Mode.
2.2.3 F
ILE
T
RANSFER
M
ODE
Use the software selection utility to set up the
Autoswitch to File Transfer Mode. The SW179A dual bus
permits only that the computer attached to Port A can
do file transfer with the computer attached to Port B.
The same goes to Port C and Port D.
2.2.4 S
OFTWARE
S
ELECTION
See the README file on the driver disk for complete
instruction. This software driver will run an application
in the background and will not do any modification to
your system .INI settings.
2.3 Autoswitch Dual-Bus Design
The Autoswitch has two independent channels for the
switch which provide simultaneous access of either
device by any of the two attached computers. If two PCs
send their jobs simultaneously to two different ports, the
print job will be processed at the same time. But if the
9
COMPACT BIDIRECTIONAL DUAL BUS AUTOSWITCHES
two PCs send their jobs to the same output port, the
first-come, first-serve rule will follow.
2.3.1 A
N
E
XAMPLE OF
S
IMULTANEOUS
O
PERATION WITH THE
SW178A
NOTE
PA is the print device on port PA.
PB is the print device on port PB.
Computer A sends a print job to PA and Computer B
sends a print job to PB. Computer A and Computer B
run the File Transfer Program.
2.3.2 A
N
E
XAMPLE OF
S
IMULTANEOUS
O
PERATION WITH THE
SW179A
Computer A sends a print job to PA and Computer C
sends a print job to PB. Computer A and Computer B
run the File Transfer Program while Computer D sends
a print job to PA.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Black Box Changer
Black Box
Black Box LGB5124A-R2 Manuel utilisateur
Black Box
Black Box AC1032A-2 Manuel utilisateur
Black Box
Black Box IC445A Manuel utilisateur
Black Box
Black Box SW056A Manuel utilisateur
Black Box
Black Box VSW-HDMI8X8-B Manuel utilisateur
Black Box
Black Box MODULAR SMART SWITCH SW925AE Manuel utilisateur
Black Box
Black Box S-COS/2 Manuel utilisateur
Black Box
Black Box LB9020A Manuel utilisateur
Black Box
Black Box LBH3050A Manuel utilisateur
Black Box
Black Box ServSwitch Secure Plus (with USB) Manuel utilisateur
Black Box
Black Box MEG821AE Manuel utilisateur
Black Box
Black Box LEH1104A-2GSFP Manuel utilisateur
Black Box
Black Box PS/2 Manuel utilisateur
Black Box
Black Box ServSensor JR EME102A Manuel utilisateur
Black Box
Black Box LPB208A-R2 Manuel utilisateur
Black Box
Black Box EMS100G32-R2 Manuel utilisateur
Black Box
Black Box LPB1205A Manuel utilisateur
Black Box
Black Box ServSwitch DT Basic II KV7024A Manuel utilisateur
Black Box
Black Box ACX576 Manuel utilisateur
Black Box
Black Box LIG1014A Manuel utilisateur
