Black Box SW035A Manuel utilisateur

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

MARCH 2001

SW035A SW580A

SW059A SW640A

SW076A SW694A

SW077A SW830A

SWL090A SW920A

6-to-1 Manual Switches

G F E C D B A

6-TO-1 MANUAL SWITCHES

TRADEMARKS USED IN THIS MANUAL

Any trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

6-TO-1 MANUAL SWITCHES

1. Specifications

Leads Supported:

SW035A: 1–9

SW059A: 24 (Pin 25 tied common)

SW076A: 1–6

SW077A: 1–8

SWL090A: 2–8, 15, 17, 20, 22, Pin 1 tied common

SW580A: Center conductor and shield

SW640A: Center conductor and shield

SW694A: 1–6

SW830A: 4 leads

SW920A: 15 leads

Connectors:

SW035A: DB9 female

SW059A: DB25 female

SW076A: 6-wire female

SW077A: 8-wire female

SWL090A: DB25 female

SW580A: BNC or TNC female

SW640A: BNC and TNC

SW694A: 6-wire MMJ female

SW830A: 4-position terminal block

SW920A: VGA female

Power: None needed

Size: SW059A, SWL090A, SW830A: 3.5"H x 6"W x 6.3"D (8.9 x 15.2 x 16 cm); All

others: 2.5"H x 6"W x 6.3"D (6.4 x 15.2 x 16 cm)

Weight: 1.5 lb. (0.7 kg)

6-TO-1 MANUAL SWITCHES

2. Introduction

About Your Switch

The switch you’re about to install is one of the best low-cost investments you can

make for your system. You’ll extend the life of your peripherals and add hours to

your work month with the time you eliminate in cabling and recabling.

The switch itself is one of the most durable devices you’ll ever own—the all-

mechanical operation and self-cleaning wiper action make for resistance to wear, a

very low failure rate, and years of life.

Our switches come in versions for nearly every connector on the market. If you

have any special requirements, such as unusual connector configurations or special

pinning, call us. We can get you a custom switch for your application.

Before You Install…

It’s easy to install your switch. The procedure is simple—it should be almost

instinctive for anyone who has ever hooked up a PC, VCR, or stereo system.

But there are a few things to be careful about. Before you start your installation,

check this list of cautions:

•Unplug everything. You should use the same care when installing your switch

that you use for connecting a PC or speaker. Although the switch doesn’t draw

current, your devices do, so unplug the power for all of them before you begin.

•Consider surge protection. The switch will not actively resist power surges, and can

pass along enough energy from a major surge to damage your data or equip-

ment. You might want the protection of an in-line surge protector. Call for

details on the surge protector that best fits your system.

•Don’t use a manual switch with laser printers. The delicate circuitry in any laser

printer could be damaged by the small amount of energy that any manual

switch passes. If you need a switch for a laser printer, ask about our electronic

switches.

6-TO-1 MANUAL SWITCHES

3. Installation

Where to Put the Switch

The switch can be put almost anywhere. The site should be flat, dry, and stable,

and you should be able to reach the knob on the front easily. You don’t have to

worry much about airflow—the switch won’t get very hot.

Cables

You’ll need seven lengths of cable. Check your manufacturer’s specifications for

information on pinning—DTE-to-DTE connections, for example, will require

cross-pinned cable. Call us if you need cables. We can supply them for almost any

application.

All the switches, except the MMJ Switch (SW694A), are pinned straight through—

they don’t switch any leads during the passage of your signal. The MMJ Switch uses

a special cross-pinning scheme that lets you use your existing cables to make

connections.

Setting Up the Switch

Gather your cables and follow these steps:

1. Set your switch in the site you’ve chosen.

2. Turn off the power to all the devices you’ll connect to the switch.

3. Turn your switch around so that the connectors are facing you. The connector

marked “C” is the common connector. Run a cable from that connector to the

common device you wish to share with your multiple devices.

4. The other connectors on the rear—A, B, D, E, F, and G—are for the multiple

devices. Run cables from the connectors to those devices.

5. Check your configuration against the diagram on the next page. Add power to

your devices, activate one after another, and switch between them to check

your connections.

6-TO-1 MANUAL SWITCHES

“A” through

“G” devices

Common device

(to “C” connector)

6-to-1 switch

6-TO-1 MANUAL SWITCHES

4. Connectors

A variety of 6-to-1 switches is available. The chart below shows all the available

connectors and pinnings. We might have updated our stock since this chart was

printed, so call us if you don’t see the switch you need.

Category Outline Type Leads supported Code

DB DB25 parallel 24 (25 common) SW059A

DB25 serial 2–8, 15, 17, 20, 22 SWL090A

DB9 9 SW035A

DB15HD 15 SW920A

RJ RJ-11 6 SW076A

RJ-45 8 SW077A

MMJ MMJ 6 SW694A

Barrier Block 4-wire 4 SW830A

Coaxial Coax BNC or TNC SW580A

WANG®

compatible BNC and TNC SW640A

NOTES

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Black Box Changer

Black Box

Black Box VSW-HDMI2X1-4K Manuel utilisateur

Black Box

Black Box LGH1004A Manuel utilisateur

Black Box

Black Box ServSwitch Wizard DVI KV1002A Manuel utilisateur

Black Box

Black Box ACX1004 SERIES Manuel utilisateur

Black Box

Black Box LGB5028A Manuel utilisateur

Black Box

Black Box ServSwitch Secure SW2006A-USB-EAL Manuel utilisateur

Black Box

Black Box AC1032A-2 Manuel utilisateur

Black Box

Black Box LB9002A-SC-R3 Manuel utilisateur

Black Box

Black Box MODULAR SMART SWITCH SW925AE Manuel utilisateur

Black Box

Black Box LGB5124A Manuel utilisateur

Black Box

Black Box IC562A Manuel utilisateur

Black Box

Black Box SW177A Manuel utilisateur

Black Box

Black Box KV6222A-R2 Manuel utilisateur

Black Box

Black Box Peripheral Sharer 2 to 1 Manuel utilisateur

Black Box

Black Box LGB1048A Manuel utilisateur

Black Box

Black Box ServSwitch Octet KV1700 Manuel utilisateur

Black Box

Black Box ServSwitch Wizard SW652A Manuel utilisateur

Black Box

Black Box AC505A-2A Manuel utilisateur

Black Box

Black Box Stackable MiniHub Manuel utilisateur

Black Box

Black Box LIG1014A Manuel utilisateur

Black Box

Black Box SS4P-DVI-4X2-UCAC Manuel utilisateur

Black Box

Black Box SWL065A Manuel utilisateur

Black Box

Black Box ServSwitch KV0004A Manuel utilisateur

Black Box

Black Box ServSwitch DT Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur