Black Box Maverick SW161A Manuel utilisateur

V.03/2004

Power Switch

Maverick SW161A

Power Management and

Server Supervision

User Guide

SW161A Power Switch Maverick 1-Port User Guide

SW161A Power Switch

User Guide

The SW161A Power Switch is a power control unit with a built-in Web server, an Ethernet and a

serial RS232 connection. It enables to control the power supply of a power outlet either remotely

through a network (Intranet or Internet) or locally through its serial RS232 connection.

Its special Pinging and Scanning functions also allow the SW161A to supervise IP devices

(servers, routers...) and automatically reboot them in case of lock-up.

Chapters

1. Safety instructions to be read before use!

2. Configuration of the Power Switch

3. Configuration using the Power Switch Finder program

4. Configuration using a Web browser

5. Configuration using a Terminal connection

6. Security parameters configuration

7. Ping and Port Scanning

8. Serial port pin configuration

9. Command the state of the socket through a Web browser

10.Command the state of the socket through a serial connection

11.Technical characteristics

SW161A Power Switch Maverick 1-Port User Guide

1. Safety instructions: To be read before use!

 The Power Switch devices can only be installed by qualified people with the following

installation and use instructions. The manufacturer disclaims all responsibility in case of a

bad utilisation of the Power Switch devices and particularly any use with equipments that

may cause personal injury or material damage.

 This equipment is designed to be installed on a dedicated circuit that must have a circuit

breaker or fuse protection.

 The electrical power socket used to plug the power cord of the Power Switch devices must

be close to the Power Switch devices and easily accessible.

 Check that the power cord, plug and socket are in good condition.

 The Power Switch devices can only be connected to three-wire 230 VAC (50-60Hz) sockets.

 Always plug the Power Switch devices into properly grounded power sockets (two poles plus

ground).

 Never exceed 10 Amp total load.

 If you have to replace an external fuse of an Power Switch device, never use another type of

fuse than 10A/250V T.

 The Power Switch devices are intended for indoor use only. Do NOT install them in an area

where excessive moisture or heat is present.

 Always disconnect the power cord of the Power Switch device if you want to intervene on the

Power Switch device or on the equipment powered from the Power Switch device.

 The power outlet of the Power Switch device is not a circuit breakers! If you want to intervene

on equipment connected to an Power Switch device you must disconnect this equipment

from the Power Switch device.

 The Power Switch devices contain potentially hazardous voltages. Do NOT attempt to

disassemble them.

 The Power Switch devices contain no user serviceable parts and repairs are to be performed

by factory trained service personnel only.

SW161A Power Switch Maverick 1-Port User Guide

2. Configuration of the Power Switch

To use the Power Switch on your network you must first configure its network parameters. Ask

your network administrator for the parameters to use.

There are three different methods to configure the Power Switch:

Method 1:

Through a network using the Power Switch Finder Program (on the delivered CD).

It is the simplest and fastest configuration method if you use Windows as operating system. We

suggest that you use this program at least during the first configuration: it allows you to

configure your Power Switch through your local network even if its network parameters (IP

Address, Subnet mask and Port) are not compatible with those of your PC or your local

network.

If you decide to use this method you can directly go to §3 "Configuration using the Power Switch

Finder program".

Method 2:

Through a network using a Web browser (Internet Explorer > 6.0 and Netscape > 6.1).

This method can only be used if the network parameters of the Power Switch (IP Address,

Subnet mask…) have already been configured using either the Power Switch Finder program

(Method 1) or a Terminal program (Method 3).

For the first configuration you can also change the Network parameters of your PC according to

the default settings of the Power Switch.

Default Network setting of the Power Switch:

IP Address: 192.168.100.100

Mask: 255.255.255.0

Port: 80

If you decide to use this method you can directly go to §4 "Configuration using a Web browser".

Method 3:

Through a RS232 serial connection using a Terminal connection (see §7 "serial port pin

configuration" for the configuration of the serial interface connector).

If you use a PC, use the serial cable supplied with the product and a Terminal program such as

HyperTerminal from Microsoft.

If you decide to use this method you can directly go to §5 "Configuration using a Terminal

connection".

SW161A Power Switch Maverick 1-Port User Guide

3. Configuration using the Power Switch Finder program

Remarks:

∇ The Power Switch and the PC used to configure it have to be connected on the same

segment of the network. The protocol of this program can not be routed so it can not be used

to configure the Power Switch through a WAN or the Internet.

∇ This program does not work if the administrator has deactivated it in the configuration of the

Power Switch (for security reasons for example).

1. Start the program PS-Finder.exe on the CD-ROM.

The Power Switch Finder window appears.

2. In the tool bar click on the first left button or choose the File/Scan Menu.

The program browses the segment on which is connected your PC and displays the name,

the type, the IP and MAC Address of the connected Power Switch.

3. In the tool bar click on the second left button or choose the File/Configure Menu.

The properties dialog box appears and you can now configure all parameters. To configure

all other parameters click on the Options button on the bottom of the dialog box.

SW161A Power Switch Maverick 1-Port User Guide

General Tab

This tab is used to attribute all the network parameters.

Labels Tab

This tab is used to attribute a name to the device and its controlled power socket.

User Accounts Tab

This tab is used to attribute a name and a password to the administrator and the user.

Security Tab

This tab is used to define addresses which are authorised or denied access to the Power Switch

over the Network. For all details about this features please refer to chapter 6 "Security

parameters configuration".

Supervision Tab

This tab is used to define the IP address of the device which has to be supervised and all the

corresponding parameters. The Power Switch can supervise IP devices by pinging a specific IP

address and/or by scanning a specific port number.

Remark: the supervision function works only if the power outlet is ON.

Options Tab

This tab is used to define the default status of the controlled power socket after power up and

the delay for the restart function.

Miscellaneous Tab

This tab indicates the number of Power Ups and the number of switching cycles from OFF to

ON.

SW161A Power Switch Maverick 1-Port User Guide

4. Configuration using a Web browser

Remarks:

∇ In order to be able to access the Web server of the Power Switch, you must before have

configured its network parameters (ask your network administrator).

∇ The configuration using a Web browser does not work if the administrator has deactivated it

in the configuration of the Power Switch (for security reasons for example).

∇ The Web server of the Power Switch works with Internet Explorer Version 6.0 or higher and

with Netscape Version 6.1 or higher.

1. Start your Web browser.

2. Type the IP address of your Power Switch.

The browser displays the authentication dialog box.

3. Enter the administrator name (default value = admin) and the administrator password (default

value = admin) and click on OK.

The home page is displayed, allowing you to configure all the parameters of the Power

Switch.

SW161A Power Switch Maverick 1-Port User Guide

Home Tab

This tab is used to switch on, off and restart the controlled power socket and to configure the

Power Switch.

General Tab

This tab is used to:

- attribute a label to the Power Switch and its controlled power socket

- define all IP parameters (IP Address, Subnet mask, Gateway and Port number)

- enable or disable the use of the Power Switch Finder program

- enable or disable the configuration of the Power Switch through HTTP.

Security Tab

This tab is used to define the Name and the Address of the Administrator and the User.

It’s also used to set the Network Security Masks. For all details about this features, please refer

to chapter 6 "Security parameters configuration".

Supervision Tab

This tab is used to define the IP Address of the device that has to be supervised and all the

corresponding parameters. The Power Switch can supervise IP devices by pinging a specific IP

address and/or scanning a specific port number.

Remark: the supervision function works only if the power outlet is ON.

Options Tab

This tab is used to define the default status of the controlled power socket after power up and

the delay for the restart function. This tab also indicates the number of Power Ups and the

number of switching cycles from OFF to ON.

SW161A Power Switch Maverick 1-Port User Guide

5. Configuration using a Terminal Connection

The RS232 serial port of the Power Switch can be used to control its power socket and to

configure its Web server.

To configure the Web server:

1. Use the supplied RS232 serial cable to connect the Power Switch-1 to an available serial port

of your PC.

2. Run a terminal program such as Windows HyperTerminal.

3. Configure the appropriate serial port with the following settings:

9.600 bauds, 8 bits, no parity, 1 stop bit and no flow control.

SW161A Power Switch Maverick 1-Port User Guide

4. From your computer, press <ENTER> until the prompt «>» appears on your screen.

(the Power Switch is now in Command mode and is waiting for commands to switch the

power socket).

5. Press the <TAB> key on your keyboard.

The Configuration menu appears on your screen and the Power Switch is now in

Configuration mode. Follow the menu to configure the Web server of your Power Switch.

All commands start with the slash «/»

(ex.: type the command /NP to go to the Network Parameters setting menu.

To display the current menu again, press <ENTER>.

To go to the previous menu and to display it, press <ESC>.

Remark: to leave the configuration mode, type the restart command /RS. This is particularly

important if you want to control the power outlet later through the serial connection.

Power Switch 1 Guard

Version: 1.2.0.2

Commands :

Display

/DS Display Socket State

Control

/SS Switch the socket

Configuration

/NP Network Parameters Setting

/PS Passwords Setting

/NS Device and Socket Name Setting

/SP Socket Parameters Setting

/SU Device Supervision Setting

/IS IP Security Setting

/RS Restart the Device

Enter Selection

Table des matières

Autres manuels Black Box Changer

Black Box

Black Box LBH120A-H SERIES Manuel utilisateur

Black Box

Black Box ISU2011-4-UK Manuel utilisateur

Black Box

Black Box AC1032A-2A Manuel utilisateur

Black Box

Black Box High-Speed SME V.35-M34 Manuel utilisateur

Black Box

Black Box ServSwitch ACR9000A Manuel utilisateur

Black Box

Black Box IC454AE Manuel utilisateur

Black Box

Black Box LGB708A-R3 Manuel utilisateur

Black Box

Black Box SW613A Manuel utilisateur

Black Box

Black Box LB9006A-SC Manuel utilisateur

Black Box

Black Box LGB5028A Manuel utilisateur

Black Box

Black Box KV1044A-R2 Manuel utilisateur

Black Box

Black Box LHB8050A Manuel utilisateur

Black Box

Black Box LGB616A Manuel utilisateur

Black Box

Black Box MT210A Manuel utilisateur

Black Box

Black Box EMS100G-32 Manuel

Black Box

Black Box ServSwitch KV0202A Manuel utilisateur

Black Box

Black Box LPD100A Manuel utilisateur

Black Box

Black Box SS4P-SH-DP-U Manuel utilisateur

Black Box

Black Box PI9120A Manuel utilisateur

Black Box

Black Box ServSwitch ACR9000A Manuel utilisateur

Black Box

Black Box LGB2118A-R2 Guide de l'utilisateur

Black Box

Black Box LGB4308A Manuel utilisateur

Black Box

Black Box LB8418A Manuel utilisateur

Black Box

Black Box LGB105A Manuel du propriétaire

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur