Black Box LEH1008A Manuel utilisateur
BLACK BOX®
Hardened Managed Ethernet Switches Quick Start Guide
LEH1008A LEH1008A-2GSFP
LEH1008A-2MMSC LEH1008A-2SFP
LEH1008A-2MMST
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Customer
Support
Information
Available models
Part Number Product Name Description
LEH1000 Series
LEH1008A 8-Port 10/100 Mbps PoE Hardened Managed
Ethernet Switch
8 ports, 10/100 PoE (802.af), DC power
LEH1008A-2GSFP 8-Port 10/100 Mbps PoE 2-Port GE SFP Hardened
Managed Ethernet Switch
8 ports, 10/100 PoE (802.af), 2 ports GE SFP,
DC power
LEH1008A-2MMSC 8-Port 10/100 Mbps PoE 2-Port 100-Mbps MMSC
Hardened Managed Ethernet Switch
8 ports, 10/100 PoE (802.af), 2 ports 100BFX, SC,
DC power
LEH1008A-2MMST 8-Port 10/100 Mbps PoE 2-Port 100-Mbps MMST
Hardened Managed Ethernet Switch
8 ports, 10/100 PoE (802.af), 2 ports 100BFX, ST,
DC power
LEH1008A-2SFP 8-Port 10/100 Mbps PoE 2-Port SFP 100-Mbps
Hardened Managed Ethernet Switch
8 ports, 10/100 PoE (802.af), 2 ports 100BFX SFP,
DC power
This quick start guide describes how to install and use the hardened Managed Ethernet Switch. Designed for rugged
environments, Hardened Managed Ethernet Switches provide reliable switching in industrial areas constrained by space.
Functional Description
• Supports IEEE 802.3af Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
• Includes redundant power inputs: 47 to 57 VDC terminal block and 47–57 VDC jack.
• Power consumption: Device 15 W max. (without PoE); PoE power budget: 123.2 W max., PoE power output:
Ports 1–8: IEEE 802.3af: Up to 15.4 W/port, 47–57 VDC.
• Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock, and vibration for traffic control equipment.
• Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environments.
• Supports IEEE 802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation: 1000-Mbps full duplex; 10/100-Mbps full-/half-duplex;
Auto MDI/MDIX.
• Supports Command Line Interface in RS-232 console.
• 100BASE-FX: Multimode SC or ST type; single-mode SC or ST type. 100BASE-BX: WDM single-mode SC type.
• 1000BASE-SX/LX: Multimode or single-mode SC type. 1000BASE-BX: WDM single-mode SC type.
• Supports 8192 MAC addresses. Provides 2M bits memory buffer.
• Alarms for power and port link failure by relay output.
• Supports DIN-rail or panel mounting installation.
• RS-232 console, Telnet, SNMP v1 & v2c & v3, RMON, Web Browser, and TFTP management.
724-746-5500 | blackbox.com
Page 2
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
• Field Wiring Terminal: Use copper conductors only, 60/75° C, 12-24 AWG torque value 7 lb-in.
• Operating voltage and Max. current consumption: 0.31 A @ 48 VDC. Power consumption: 123.2 W max. (Full load with PoE),
15 W max. (without PoE).
Physical Description
Designed for rugged environments, Hardened Managed Ethernet Switches provide reliable switching in industrial areas.
Front panel of Front panel of Back panel (all models)
LEH1008A-2MMSC or LEH1008A-2SFP or
LEH1008A-2MMST LEH1008A-2GSFP
3
4
5
10
2
7
6
3
4
5
10
1
7
6
9 11
8
NOTE: LEH1008A (not shown) has (8) RJ-45 ports and no ST, SC, or G1/G2 ports.
Figure 1. LEH1000 Series Hardened Managed Ethernet Switch.
LEH1000 Series switches components.
Number in Figure 1 Product Name Description
1Ports G1 and G2 LEH1008A-2GSFP: (2) GE SFP ports;
LEH1008A-2SFP: (2) SFP ports
NOTE: These connectors are not present on LEH1000A-2MMSC
and LEH1000A-2MMST switches.
2(2) ST or SC fiber ports LEH1008A-2MMSC: (2) 10/100 MM SC ports;
LEH1008A-2MMST: (2) 10/100 MM ST ports
NOTE: These connectors are not present on LEH1008A-2GSFP and
LEH1008A-2SFP switches.
3(8) RJ-45 ports All LEH1000 Series switches: 10/100 Mbps PoE ports
4(8) TX LEDs See the Indicators table on the next page.
5(8) RX LEDs See the Indicators table on the next page.
6Per port: (2) LINK/ACT LEDs See the Indicators table on the next page.
7Per port: (1) PoE LED On when port is connected to a PoE PD (Powered Device).
8(1) Phoenix connector Terminal block for Power 1, Power 2, and Ground
9(1) DC power connector Links to DC power source
10 (1) DB9 connector Used for RS-232 serial control
11 (1) Reset button Press to reset the switch to factory defaults.
724-746-5500 | blackbox.com Page 3
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
LEH1000 Series Switches Indicators.
LED State Indication
Power 1 Steady ON (Green) Power ON
Off Power OFF
Power 2 Steady ON (Green) Power ON
Off Power OFF
Power 3 Steady ON (Green) Power ON
Off Power OFF
10/100BASE-TX, 100BASE-FX/BX
LINK/ACT Steady ON (Green) A valid network connection is established
Flashing Transmitting or receiving data.
NOTE: ACT stands for activity.
100 Steady ON (Green) Connection at 100-Mbps speed.
10/100/1000BASE-SX/LX/BX
LINK/ACT Steady ON (Green) A valid network connection is established
Flashing Transmitting or receiving data.
NOTE: ACT stands for activity.
1000 Steady ON (Green) Connection at 1000-Mbps speed.
Power Input Assignment
Power 3 47–57 VDC DC jack
Power 2 +47–57 VDC
-Power ground
Power 1 +47–57 VDC
-Power ground
Earth ground
Relay output rating 1 A @ 250 VAC
Relay Alarm Assignment
Fault Warning signal disable for the following:
• The relay contact closes if Power 1 and Power 2 both fail, but Power 3 is ON.
• The relay contact closes if Power 3 fails, but Power 1 and Power 2 are ON.
724-746-5500 | blackbox.com
Page 4
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
Console Configuration
STEP 1: Connect to the switch console.
Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of the terminal or computer
running the terminal emulation application. For direct access to the administration console, connect a terminal or a PC equipped
with a terminal-emulation program (such as HyperTerminal) directly to the switch console port.
STEP 2: Configure the terminal-emulation program settings.
When using the management method, configure the terminal-emulation program to use the following parameters (you can
change these settings after login):
Default parameters:
• 115,200 bps
• 8 data bits
• No parity
• 1 stop bit
STEP 3: Press the “Enter” key.
The Command Line Interface (CLI) screen should appear.
STEP 4: Log on to Exec Mode (View Mode).
At the “switch_a login:” prompt, type in “root” and press <Enter> to log on to Exec Mode (or View Mode). The “switch_a>”
prompt will show on the screen.
Exec mode (View mode) screen.
724-746-5500 | blackbox.com Page 5
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
STEP 5: Log on to Privileged Exec Mode (Enable Mode).
At the “switch_a>” prompt, type in “enable” and press <Enter> to log on to Privileged Exec Mode (or Enable Mode). The
“switch_a#” prompt will show on the screen.
STEP 6: Log on to Configure Mode (Configure Terminal Mode).
At the “switch_a#” prompt, type in “configure terminal” and press <Enter> to log on to Configure Mode (or Configure Terminal
Mode). The “switch_a(config)#” prompt will show on the screen.
Configure terminal mode screen.
724-746-5500 | blackbox.com
Page 6
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
Web Configuration
STEP 1: Login to the switch.
Specify the default IP address (192.168.1.10) of the switch in the Web browser. A login window will be shown as below:
Login window.
724-746-5500 | blackbox.com Page 7
LEH1000 Series Hardened Ethernet Switches Quick Start Guide
STEP 2: Log in using the factory default settings.
• Enter the factory default login ID: root.
• Enter the factory default password (no password).
• Click on the “Login” button to log on to the switch.
Welcome screen.
724-746-5500 | blackbox.com
About Black Box
Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks
and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7 Tech support
available in 60 seconds or less.
© Copyright 2014. Black Box Corporation. All rights reserved. Black Box®and the Double Diamond logo are registered trademarks of BB Technologies, Inc.
Any third-party trademarks appearing in this manual are acknowledged to be the property of their respective owners.
BLACK BOX®
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 60 seconds away at 724-746-5500 or blackbox.com.
LEH1008A Quick Start Guide, version 2
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Black Box Routeur réseau
Black Box
Black Box Multiport Analog VoIP Gateway Router VOE231A Manuel utilisateur
Black Box
Black Box lgb2001a Manuel utilisateur
Black Box
Black Box LR120A Manuel utilisateur
Black Box
Black Box LB9007A-SC-R3 Manuel utilisateur
Black Box
Black Box LGB4005A Manuel utilisateur
Black Box
Black Box LGH1006A Manuel utilisateur
Black Box
Black Box 5000 series Manuel utilisateur
Black Box
Black Box LEH1208A Manuel utilisateur
Black Box
Black Box LB9213A Manuel utilisateur
Black Box
Black Box LGB2007A Manuel utilisateur
Black Box
Black Box Nortel Secure 1001 Manuel utilisateur
Black Box
Black Box LGB316A-R2 Manuel utilisateur
Black Box
Black Box LR0003A Manuel utilisateur
Black Box
Black Box COS-4P Manuel utilisateur
Black Box
Black Box LR0019A-4U Manuel utilisateur
Black Box
Black Box WRT750A Manuel utilisateur
Black Box
Black Box LB9017A-R3 Manuel utilisateur
Black Box
Black Box Version 1.0 Manuel utilisateur
Black Box
Black Box LW001A Manuel utilisateur
Black Box
Black Box LPH1006A-R2 Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité