Black Box COE-8I Manuel utilisateur

LEMV295034

LEEM295035

8 Port COE-8I & COE-8O

Contact Closure Over Ethernet

Overview

COE-8 is a system for transporting switch closure information over a TCP/IP network. The COE-8

consists of two devices, and Transmitter Unit (COE-8I) and a Receiver Unit (COE-8O). The COE-8I

provides 8 inputs for switch contacts, relay closures or DC Voltage. Upon a change of state for any

channel, it will transmit a message to one or more (up to 32) COE-8O units. The COE-8O has eight

relays that will mirror the status of the eight inputs of the COE-8I. Each unit can be monitored and

configured from a Web Browser.

Hardware Installation

Inputs (COE-8I)

Connect the inputs to the COE-8I using the screw terminals on the printed circuit card, as illustrated. Inputs

can be either dry relay or switch contacts, or a +VDC voltage (3 to 30 V), referenced to a common ground.

Status Dry Relay DC Voltage

Open Open >3VDC

Closed Closed <=0VDC

Input Specification Dry Contact (common ground) or Wet ±30VDC Max

Relays (COE-8O)

Connect the inputs to the COE-8I using the screw terminals on the printed circuit card, as illustrated.

Relays are Form A. Relay Specifications

Rating (resistive) 0.5 A 120 VAC or 1 A 24 VDC

Maximum Carrying Current 2 A

Maximum Switching Power 60 AV, 24 W

Maximum Switching Voltage 120 VAC/60 VDC

Maximum Switching Current 1A

Life Expectancy: 5 Million Operations Mechanical 100K Operations at rated load

Network

Connect the network to the connector provided. A yellow LED indicates a successful connection to the

network, a green LED data activity.

Power

Apply power only when the cover is secured onto the COE-8. Use only the wall mounted power supply

provided.

Board Diagram

COE-8I COE-8O

LEMV295034 LEEM295035

WEB Page Access

The web pages provide status information on the inputs and outputs of the COE-8, as well as provide

configuration for the unit. Open a browser to the default or current IP address of the unit.

Enter the default username and password:

Factory Defaults:

IP Address 192.168.1.254

Username admin

Password admin

The unit will display the current status of each of the channels and provide buttons for Refresh, Setup

and Logout.

Configuration

Setting I/P Address

The COE-8 units provide three methods for setting the IP Address

1) Static IP via the Web Page Setup

2) DHCP

3) ARP/Ping

WEB Page

Click on the IP button to bring up the IP Settings page:

Select Static Mode from the radio buttons and fill in the IP Address, Subnet Mask and Gateway as

provided by your network administrator. Click Apply to save the changes. You will then be prompted

to reboot the COE-8. Click on the Reboot button. The COE-8 will reboot and the new IP address will

be ready to be accessed.

DHCP

Selecting DHCP from the IP Setup page allows a DHCP server to provide IP address information to

the COE-8. Click Apply and then Reboot when prompted. The COE-8 will reboot and will have to be

accessed with the IP address assigned by the DHCP server. If no IP address is assigned by a DHCP

server, the original IP address will be retained.

ARP/Ping

Select ARP/Ping radio button. Click Apply and then Reboot when prompted. Follow the steps below.

It is recommended that after a successful setting of the IP address using this method, that the Mode

be changed back to Static. This will prevent malicious programs from altering the IP address.

To set the IP address, the hardware (MAC) address must be known. This address is located on a

label on the bottom of the unit. The syntax for the MAC address is: nn-nn-nn-nn-nn-nn. To set the IP

address using ARP, connect the 10Base-T connection to your local ethernet network and apply power

to the unit. The computer used to set the IP address must be on the same subnet as the COE-8. ARP

does not work across routed or switched networks.

Windows® (98 and later)

1. Open a Command Prompt window.

2. Type the following command:

arp -s <IP Address> <MAC Address>

Where <IP Address> is the desired IP address for the COE-8 and the <MAC address> is the MAC

Address of the COE-8. The MAC Address of the COE-8 is located on the COE-8’s serial number

label. Windows 95 users see note below.

3. Ping the device to program the IP address by typing the following:

ping <IP Address>

If the ping command returns “host not responding” 4 times then the address has not been programmed

properly, or the IP Address is incorrect. In either case redo step 2. If the problem persists contact

the Tech Support Hot Line.

4. Delete the entry from the ARP cache by typing:

arp -d <IP Address>

5. Ping the device again (step 3) to confirm that the address has been programmed properly

Unix, Linux, other

Consult your systems administrator for information on setting an IP Address using ARP.

The unit should be pinged after the IP Address has been set to confirm proper operation.

Setup

The Setup button from the Home page provides access to all the configuration of the COE-8. The

Setup area is divided into several pages:

Device Page:

Basic setup of the COE-8, IP address and TCP/IP settings

Name Assign a name up to 20 characters to help identify the COE-8

IP Address Set the IP Address manually in the Static Mode (see below)

IP Modes Set the method to configure the IP address. See section above for details.

§ Static: Manually entered IP address information

§ DHCP: IP address obtained upon power up from DHCP server.

§ ARP-Ping: IP address set from another computer

Port Settings The IP Setup page also allows for changing of the port assignment for both the Control

communication and web page access. Black Box recommends changing the Web port for units that

will be connected to the Internet. This will minimize the number of hacker attacks that the COE-8 will

be subject to.

The Control Port for both the COE-8I and all COE-8Os that receive status from it must be set the same.

If a port other than the default Port 80 is used for web browser access, that port must specifically be

used in the URL when accessing the COE-8. For example, if the Web Port is changed to 9090 then

the URL for the unit would be http://192.168.1.254:9090

Receivers (COE-8I Only)

Transmission Frequency 0 to 9999 seconds

This sets the frequency that the COE-8I transmits its status to the receivers. When set to 0,

transmission will only occur upon change of status.

Receiver IP Address Set up to 32 IP addresses of the COE-8O units that will have input

status information set to them.

Inputs (COE-8I Only)

The COE-8 I can send individual input status to multiple COE-8O receivers, or other IP address. This

page provides for selecting which output of the COE-8Os will be operated by each input of the COE-8I.

Select the Input from the drop down box, then configure the Name for that input, along with the

channel of each COE-8O unit to receive the status. Use Output 0 if no output of a given COE-8O is to

be used for that channel. Configure each of the 8 inputs as necessary.

SNMP

The COE-8 can be monitored and configured via SNMP managers.

Download the MIB at ftp://ftp.blackbox.com/lan/

Enter the IP addresses of up to 4 SNMP managers. Enable or Disable SNMP with the checkbox provided.

Traps can be sent every time there is a change of state on any COE-8 channel. Check the box provided to

enable this. If both the COE-8I and COE-8O are configured to send traps, two messages will be received by

each SNMP manager for each event.

Passwords

Two username and password sets allow for two types of users:

User Type Default Username / Password Access

Administrator admin / admin Full view and setup

General User user / user View status only

Click Apply to save the new usernames and passwords.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Black Box Matériel réseau

Black Box

Black Box ServSelect KV119A Instructions d'installation et d'entretien

Black Box

Black Box LES1208A-R2 Manuel utilisateur

Black Box

Black Box TS230A-R2 Manuel utilisateur

Black Box

Black Box IC448A Manuel utilisateur

Black Box

Black Box Lineshare Master - 4 Manuel utilisateur

Black Box

Black Box 39625 Manuel utilisateur

Black Box

Black Box KVT617A Manuel utilisateur

Black Box

Black Box 38891 Manuel utilisateur

Black Box

Black Box USB Director RS-232 Manuel utilisateur

Black Box

Black Box COMPACT T1 Manuel utilisateur

Black Box

Black Box RM425A-R3 Manuel utilisateur

Black Box

Black Box SW591C Manuel utilisateur

Black Box

Black Box AC504A Manuel utilisateur

Black Box

Black Box AC1003A Manuel utilisateur

Black Box

Black Box SW551A Manuel utilisateur

Black Box

Black Box Multi Quick Check RJ-11 Manuel utilisateur

Black Box

Black Box MT1500A Manuel utilisateur

Black Box

Black Box KV1308C Manuel utilisateur

Black Box

Black Box VIDEO CCTV-A/V HUB Manuel utilisateur

Black Box

Black Box EncrypTight ET0010A Manuel utilisateur

Black Box

Black Box JPM403A-R2 Manuel utilisateur

Black Box

Black Box Veri-NAC LVN5600A Manuel utilisateur

Black Box

Black Box LES1604A Manuel utilisateur

Black Box

Black Box JPM440A Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur