Bitstream MAGNETAR-105 Guide d'installation
Quick manual www.bitstream.pl
MAGNETAR-105
Wireless Ethernet r uter 2G/3G/4G/ RS232/422/485/ I/O USB
Measurement interfaces
1 FRONT PANEL OF THE DEVICE
Front panel of the Magnetar-105
1 – SMA connectors for connecting GSM or WiFi antennas
2– slots for two SIM cards
3– signal LEDS
4– R -45 Ethernet connector
5– USB B mini connector for management
6*– RS screw connector and digital inputs
7*– RS screw connector and relay output
8– relay output
9– power connector with ground terminal
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 1/12REV. 1.03 2020.06.08
1
2
3
4
6
7
8
9
5
Quick manual www.bitstream.pl
1.1 Indication of signal LEDS
Description of the signal LEDs on the front face
– GSM signal level indicator
GSM – GSM modem status indicator
LED lights up
[s]
LED dimmed
[s] Status GSM
0.1 0.1 Initialization
0.1 2 Error
2 0.1 Ok
0 - modem off.
RS1 ACT – RS1 port activity indicator
RS2 ACT – RS2 port activity indicator
STATUS – status indicator
SERVICE – service indicator
ALARM – alarm indicator
PWR – power indicator
1.2 Designation
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 2/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
1.3 Description of device connectors
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 3/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
RJ45 connector output appearance and numbering
Ethernet interface status signaling
Each Ethernet port is equipped with two signal LEDS.
1G – Ethernet link signaling for 1000Mbit/s throughput
10/100 – Ethernet link signaling for 10/100Mbit/s throughput
The distribution of individual signals for R -45 connectors is shown in the table.
C nnect r RJ-45 (PE1-PE4) Ethernet 10/100Mbit/s
1 (orange white) RXAn
2 (Orange) RXBn
3 (white green) TXAn
6 (Green) TXBn
Channel transmitter n
Channel receiver n
C nnect r RJ-45 (PE1-PE4) Ethernet 1000Mbit/s
1 (orange white) BI_DA+ Two-way contact +A
2 (Orange) BI_DA- Two-way contact -A
3 (white green) BI_DB+ Two-way contact +B
4 (blue) BI_DC+ Two-way contact +C
5 (white blue) BI_DC- Two-way contact -C
6 (Green) BI_DB- Two-way contact -B
7 (white brown) BI_DD+ Two-way contact +D
8 (Brown) BI_DD- Two-way contact -D
n – Ethernet channel number( (1-4)
Arrangement of individual signals for the connector RS1
The remaining connectors as described on the elevation of the device*:
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 4/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
2 POWER
Polarity – pay attention to polarity (marking on the housing), the device is protected in case of
incorrect power connection.
Parameter Parameter value
Rated supply v ltage f r
versi n '5'
9-60V DC (5.5W)
0.6 - 0.09A
3 FIRST START-UP
When the power supply with the appropriate parameters is connected, the POWER LED should
light up.
4 DEFAULT ACCESS PARAMETERS FOR DEVICE MANAGEMENT
Parameters IP:
Adress: 192.168.0.100 Mask: 255.255.255.0
User: admin Password: admin
5 MANAGEMENT
Device management and monitoring can be done through a web interface using HTTP or
HTTPS. In addition, access to all management points can be accessed via a CLI terminal
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 5/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
accessible via SSH or Telnet. The device is also equipped with an SNMP agent, which provides
MIB databases containing a lot of data about the current state of the device.
Interface names in the system :
eth0 → Eth
modem1 → modem interface1
modem2 → modem interface2
6 CONFIGURATION - WWW
6.1 Set modem parameters
Mode of operation 'Configuration/modem':
Off – Disabled
On – Enabled(modem active SMS only support)
PPPD – Enabled(active network interface modem)
Choosing radio technology:
If the software does not automatically set the technology, you must manually select the
appropriate
6.2 Setting IP 'Configuration/IP/Interfaces' :
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 6/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
6.3 Setting 'gate' Default 'Configuration/Route/Dafault gateway' :
6.4 Configuration NAT 'Configuration/IPTables/DNAT' :
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 7/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
7SAMPLE CONFIGRUTATION
7.1 Configuration of DHCP server on eth0
Setting 'DHCP' :
7.2 LAN eth0 / WAN modem 1
Modem Configuration 1:
•PPPD mode
•Radio technology LTE/UMTS/GSM - Preferred LTE
IP setting, modem1 and DHCP client enabled:
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 8/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
Default gateway via GSM modem:
7.3 WAN modem1/modem2 – modems are in backup mode
Modem configuration 1 and 2:
•Mode PPPD
•Radio technology LTE/UMTS/GSM - Preferred LTE
•Two default gateways set. Priority is given to modem1.
In case there is a connection problem modem1 'gateway' switches to
modem2
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 9/12REV. 1.03 2020.06.08
Quick manual www.bitstream.pl
Default settings 'gateway':
7.4 Configuration of serial ports
* - IO port functionality implemented according to specific customer requirements.
MANUAL Magnetar-105 10/12REV. 1.03 2020.06.08
Table des matières
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité