Bircher RFGate 2.2.W2.F.A Guide rapide

12 3 4 5

2032

175

189

50.8

138

10.8

4.8

80 45

121

162

178

RFGate 2.2.W2.F.A

4.3

57.6

1 7. 0

15.5

65.7

Wireless signal transmission system for safety edges, two channels

Translation of the original operating instructions

General

1Safety instructions

2Common application

2.1 Industrial door with wicket door

ENGLISH

349284D

10/17

Warning: Switch off the operating voltage before working on the system.

Only trained, qualied personnel may perform installation and startup.

The unit may only be opened and repaired by Bircher Reglomat employ-

ees. The switching unit may only be used to protect against dangers on

crushing and shearing points and on automatic industrial doors (intended

use). National and international regulations on industrial door safety must

be complied with. Always consider the safety functions of your applica-

Transmitter 1

DIP switch 5 ON

tion as a whole, never just in relation to one individual section of the

system. A risk assessment in advance is mandatory. The installer is re-

sponsible for installing the industrial door system correctly.

It is recommended to change the batteries every year.

Transmitter 1 Transmitter 2 Receiver

Receiver

Safety edges

8.2 kΩ

Transmitter 1 input 1 corresponds to receiver output 1

Transmitter 2 corresponds to receiver output 2

Magnet

Transmitter 2

Drilling template enclosed

8K2

1 2

IN1

IN2 2)

1 2

IN1

IN2 2)

3 4 5 6 7 8

8K28K2

3 4 5 6 7 8

8K28K2

1 2

2032

1 2

2032

NC 2x

3 4 5 6 7 8

NO 5x

+/~ –/~

12/24V

AC/DC

1 2 3 4 5 6 7 8 9 10 11 12

VCC1

VCC2

COM1

OUT1

SOUT1

COM2

OUT2

SOUT2

TST1

COM.T1

TST2

COM.T2

DIP switch Sensor connection DIP switch Sensor connection

1) Change from NC to NO, see chapter 3.2

IN2 without function

Relay contacts are shown unpowered

3.2 Changing input from NC to NO (factory setting = NC)

4.2 Wiring: Outputs and control

4.3 DIP switches

3.1 DIP switch setting according to sensor (safety edge, switching contact)

4Receiver

3Transmitter 1

Gate control

with NC input

Gate control

8.2 kOhm input

Gate control with

NO input

Remove jumper(s)

4.1 Wiring: Power supply and test inputs

1 2 3 4 5

ON *Safety application

Standard

according to EN ISO 13849-1

1 2 3 4 5

ON Inactive ➔ no safety function

(Radio connection is not monitored)

12 3 4 5

ON Transmission frequency

869.85 MHz:

Set DIP-switch before pairing transmitter –

receiver

12 3 4 5

ON *868.95 MHz:

Set DIP-switch before pairing transmitter –

receiver

12 34 5

ON Test input type

activated = contact open

12 34 5

ON *NO

activated = contact closed

12 3 45

ON Automatic frequency adjustment

Active

Used only in case of severe radio disturbance

12 3 45

ON *Inactive

12 3 4 5

ON *Programming (2 transmitters)

Transmitter 1 corresponds to output 1

Transmitter 2 corresponds to output 2

12 3 4 5

ON Programming (for 2 channel transmitter)

Not for this application

*= factory setting

RFGate 2.2.S.F

Insert

battery 1

Insert

battery 2

Status

Change

concluded

Press button on

transmitter Status changes LED ashes

LED ashes 2x LED ashes 5x

> 1.5 sec.

After inserting battery 1, you have

10 seconds to change the status

Observe the

sequence

Transmitter 2 is xed to NC

Test Common

1 2

2032

1 2

2032

1 2

1 2 3 4 5

12 3 4 5

OK?

< 5 mm

LITHIUM

CR 2032

LITHIUM

CR 2032

LITHIUM

CR 2032

LITHIUM

CR 2032

6.1 Pairing the transmitter with the receiver

5Set-up

6Programming

On the trans-

mitter 1 for

channel 1

On the receiver

Press and

release button

Beep Wait 2 beeps

10 sec.

On the trans-

mitter 2 for

channel 2

Press and

release button

Beep Wait

10 sec.

On the receiver

Beep BeepRelease button Release buttonLED

lights up

LED ashesPress button

> 1.5 sec.

Press

button

> 1.5 sec.

On the receiver

BeepPress button

> 1.5 sec.

LED lights up

Transmitter 1:

mount

Release button

Transmitter 1:

insert

batteries

Transmitter 2:

insert

batteries

Please observe the torque when

fastening the cover:

Max. 45 N cm

Check DIP switch

settings

Programming (Chapter 6.1):

pair transmitter with receiver

The distance between the trans-

mitter and receiver and additional

transmitters must be at least 1 m

2 beeps

Observe

order

Code saved

LED goes out

Code saved

LED goes out

Transmitter 1:

wire

Receiver:

Turn on power

supply

Receiver: Install

and wire

11.

System test:

safety edge on gate

see 7.1

Beep

BeepBeep

Beep

Mount trans-

mitter 2 and

the magnet

10.

Note: Distance between

magnet / transmitter when

doors are closed

12.

System test wicket door:

opening and closing

see 7.1

Transmitter 1:

Transmitter 2:

Wicket

door

correctly

positioned

12345

ON SAB

SELECT

REL 1 REL21

R2R1

1 2

12345

ON SAB

SELECT

REL 1 REL21

R2R1

1 2

Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen, www.bircher-reglomat.com

LITHIUM

CR 2032

LITHIUM

CR 2032

LITHIUM

CR 2032

LITHIUM

CR 2032

7Standard operation

9Technical data

10 EC-Declaration of Conformity

11 Contact

7.1 Receiver LED indicators

7.2 Warning indicator for low battery voltage

Object

detected

LED off

Wicket doors

open

LED off

LED 1 LED 2

Signal emitted with each activation of the transmitter

Receiver

Supply voltage 12/24 V ACDC

Transmitter memory 7 + 7

Output 2 relays 24 V, 0.5 A; micro switch-off 1B

Power consumption 0.5 W @ 12 V; 1.2 W @ 24 V

Test signal input 12/24 VACDC

Protection class IEC 60529 IP55

Transmitter 1

Battery power 2 x Lithium 3 V type CR2032

Power consumption Transmitting: 17 mA standby: 16 µA

Protection class IEC 60529 IP55

Manufacturer: Bircher Reglomat AG, Wiesengasse 20, CH-8222 Beringen

Following directives have been observed: MD 2006/42/EC, RoHS 2011/65/EU, RED 2014/53/EU

EC type-examination certicate: E6945

Notied inspection centre: Suva, technology division, SCESp 0008, ID no. 1246

Product variant: RFGate 2.1.x, RFGate 2.2.x

Safety OK Wicket doors

closed

LED on LED on

Battery voltage

low

System

Frequency bands 868.95 MHz & 869.85 MHz

Range Under optimum conditions up to 100 m

Pollution degree 2

Working temperature -20 °C to +55 °C

Transmitter 2

Battery power 2 x Lithium 3 V type CR2032

Power consumption Transmitting: 17 mA standby: 16 µA

Protection class IEC 60529 IP65

6.2 Transmitter reset (Deletion of transmitter-receiver pairing)

6.3 Memory full

Press button Hold down button Short beepsBeep WaitRelease button

10 sec.

> 1.5 sec. > 3 sec.

2 beeps

On the receiver Memory cleared

on all trans-

mitters

BeepBeep Beep BeepBeep

Beep

Beep 10 sec.

8Alternative installation with double sided tape (not supplied)

Caution!

Ensure surfaces are clean, dry and free of dust and grease.

View of transmitter 2

(bottom) Double-sided

adhesive tape

6.4 Battery change

Danish seller

Swissdoor ApS, Stenhuggervej 2, DK-5471 Soendersoe

[email protected], www.swissdoor.dk

Autres manuels Bircher Système de microphone

Bircher

Bircher XRF-RD Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur