Bimba Intellipress Manuel utilisateur
INTELLIPRESS™
BENCH TOP
PRESS
User Manual
We make
things MOVE
®
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
2
WARNING
Only authorized personnel are permitted to disassemble the electric bench top press.
WARRANTY AND LIMITATIONS OF LIABILITY
For warranty information, visit www.bimba.com.
Technical support is available from:
Bimba Manufacturing Company
25150 S Governors Hwy University Park, Illinois 60484
Phone: 708-534-8544 Toll Free: 800-44-BIMBA Fax: 708-235-2014
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
3
General Information 4
Ordering Codes 4
Section 1: Startup Instructions 5
Section 1.1: Initial Login 5
Section 1.2: Initial Parameter Setting - Jog 8
Section 1.3: Definitions and Parameter Setting - Manual Run 9
Section 1.4: Definitions and Parameter Setting - Auto Run 11
Section 1.5: User Setup 12
Section 2: E-Stop / Forced Stop and Start Inputs 13
Section 1.2: E-Stop / Forced Stop and Start Inputs 13
Section 3: Recipe Selection and Auto Run 14
Section 3.1: Recipe Select 14
Section 4: Press Status, Run Count, and Error Reset 17
Section 4.1: Status 17
Section 4.2: Run Count 17
Section 4.3: Error Reset 17
TABLE OF CONTENT
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
4
GENERAL INFORMATION
ORDERING CODES
EBTP - 3K - PACL
FORCE
3K 3,000 lbs.
6K 6,000 lbs.
12K 12,000 lbs.
CONTROLS
PA Press and actuator only
PAC Press, actuator, and controls
PACL Press, actuator, controls and
load cell
PRESS
EBTP Electric Bench
Top Press
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
5
SECTION 1: STARTUP INSTRUCTIONS
Selecting the LOGIN/LOGOUT button will present the following screen pictured below. Select the LOGIN/
LOGOUT button again.
See Figure 2: Login Screen
SECTION 1.1: INITIAL LOGIN
At Power-up, the following screen below will be displayed. Select the LOGIN/LOGOUT button.
See Figure 1: Power Up Screen
LOGIN/LOGOUT BUTTON
LOGIN/LOGOUT BUTTON
This section will illustrate how to initialize the non-load cell enabled version of the IntelliPress™Electric
Bench Top Press beginning at power-up.
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
6
At the LOGIN screen, enter “SUPER” for both the Operator Name and Password and then press “ENT”
See Figure 3: Login Credentials Screen
Upon successful login, select “OK”. This will return you to the LOGIN screen with tabs populated at the
bottom of the screen.
See Figure 4: Successful Login Screen
ENT
SUCCESSFUL LOGIN
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
7
The following tabs on the screen below provide the following corresponding actions/abilities that are
available to the supervisor. See Figure 5.
Auto Run
• Select recipes
• Return to home position
• Review operational status
• View Run Count
• Taskbar: Reset Run Count, Error Reset, return to home screen, and cycle stop
Manual Run
• Set parameters for manual operations
• Jog+ / Jog-
• Advance to home, initial, approach, and full down positions
• Taskbar: reset errors, return to home screen and cycle stop
Recipe Settings
• Call up and adjust recipe parameters
• Taskbar: reset errors, return to home screen, and cycle stop
User Setup
• Modify user access settings
• Change administrator password
See Figure 5: Logged-In Screen
ENT
MANUAL RUN
AUTO RUN RECIPE SETTINGS RECIPE SETTINGS
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
8
SECTION 1.2: INITIAL PARAMETER SETTING - JOG
Press operations are made simpler by first establishing Jog parameters. To configure the Jog parameters
follow the steps below:
• From the Logged-in screen (Figure 5 pictured on page 7), select the Recipe Settings tab.
• Select the Jog button located in the Task Bar section of the screen (Figure 6).
• Press on the Jog Speed Value (0.00 in this case) and enter the jog speed values in units in mm/sec. A
maximum jog speed value of 50mm/sec is recommended.
»Jog+ will extend the press ram DOWN.
»Jog- will extend the press ram UP.
• Press the Home icon located in the taskbar to return to the Logged in screen.
See Figure 6: Jog Speed Selection
JOG+ SPEED
JOG- SPEED
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
9
SECTION 1.3: DEFINITIONS AND PARAMETER SETTING - MANUAL RUN
Operation of the IntelliPress™Electric Bench Top Press can be performed via either recipes or manual
operations. For Manual Run operation setup see the following below:
From the Logged-in screen (Figure 5), select the Manual Run tab.
See Figure 5 below:
From the Setup - Manual Operations screen (Figure 7), select the recipe to be modified
MANUAL RUN
INTELLIPRESS™ELECTRIC BENCH TOP PRESS
User Manual
BIM-IEBTPM-1218 Rev 1 | For Technical Assistance: 800-442-4622
10
Press on the parameters to be modified to bring up a pop-up keypad (Figure 8).
See Figure 8: Pop-Up Keyboard
The following parameters can be modified from the Setup - Manual Operations Screen:
• Jog+ / Jog-: Indexes the press ram UP (+) or DOWN (-).
• Initial Position: The location below the Home Position to where the press will return after each
automatic cycle.
• Initial Position Speed: The speed at which the press travels from the Home Position to the Initial
Position and from the Approach Position to the Initial Position.
• Approach Position: The location below the Initial Position where pressing torque begins.
• Approach Position Speed: The speed at which the press travels from the Initial Position to the
Approach Position. This also includes the speed at which the ram will retract to the Home Position.
• Full Down Press Position: The final ram position.
• Full Down Press Position Speed: The speed at which the press applies force in the downward
direction.
• Full Down Press Position Force: Expressed as a percentage of the force rating of the press, this is the
pressing force applied to the part.
• Home Position Button: Directs the press ram to the Home Position.
• Initial Position Button: Directs the press ram to the Initial Position.
• Approach Position Button: Directs the press ram to the Approach position.
Taskbar Definitions:
• Error Reset: Resets any alarms or faults in the press controller.
• Home Icon: Returns to the Logged-In Screen (See Figure 5 on page 9).
• Stop Icon: Stops the program operation of the press. Note: The stop icon does NOT remove power
from the motion control system
Modify the Setup - Manual Operations values as necessary.
When manual operations are complete, press the Home icon.
Table des matières
