Billy Goat FORCE 602V Manuel utilisateur

FORCETM 6O2V & 602X BLOWER Owner’s Manual

Part No 441502 1441502_A_HI

FORCE BLOWER Owner's Manual

F602V, F602X

ACCESSORIES

Original Instructions

IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE

FRONT AIR DIRECTOR

Simple to attach, allowing air

to be directed forward.

PN# 441130

HOSE KIT

Easily attached hose and

nozzle for hard to reach

places.

PN# 441166

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

CONTENTS

SPECIFICATIONS, SAFETY, & INSTRUCTION LABELS 3

PACKING CHECKLIST 4

ASSEMBLY 5-6

OPERATION AND MAINTENANCE 6-7

TROUBLESHOOTING 8

ILLUSTRATED PARTS LIST 9-10

Go to http://www.billygoat.com for French-Canadian translations of the product manuals.

Visitez http://www.billygoat.com pour la version canadienne-française des manuels de produits.

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

SPECIFICATIONS

F602V F602X

Engine HP 5.0 HP (kW) 4.74 HP (3.53kW)

Engine Model 10V3320003F1 130G320231F1

Engine Type B & S VANGUARD ENGINE B&S XR

Engine Fuel Capacity 3.3 qt. (3.1 L) 3.2 qt. (3.0 L)

Engine Oil Capacity 0.63 qt.(0.60 L) 0.63 qt. (0.60 L)

Total Unit Weight 89 lb (40.3 kg) 83 lb (38kg)

Overall Length 43.5" (1.1m) 43.5" (1.1m)

Overall Width 22” (0.56m) 22” (0.56m)

Overall Height 45" (1.14m) 45" (1.14m)

Max Operating Slope 20o20o

SAFETY

WARNING

This product can expose you to chemicals including gasoline engine exhaust, which is known to the State of California to cause

cancer, and carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm. For

more information go to www.P65Warnings.ca.gov.

INSTRUCTION LABELS

The labels shown below were installed on your BILLY GOAT®FORCETM Blower. If any labels are damaged or missing, replace

them before operating this equipment. For your convenience in ordering replacement labels, part numbers are included in the

Illustrated Parts List. The correct position for each label may be determined by referring to the Figure and Item numbers shown.

LABEL SPARK ARRESTOR

P/N 100252

LABEL EXPLOSIVE FUEL

ITEM # 34 P/N 400268

LABEL READ OWNERS MANUAL

ITEM # 35 P/N 890301

LABEL SAFETY PROTECT

ITEM # 36 P/N 100346

LABEL FLYING DEBRIS

ITEM # 37 P/N 810736

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

PACKING CHECKLIST

These items should be included in your carton. If any of these parts are missing, contact your dealer.

Your BILLY GOAT®FORCE Blower was shipped in one carton, completely assembled except for the front wheel, upper handle

assembly, and the Aim-N-ShootTM cable.

READ all safety instructions before assembling unit.

TAKE CAUTION when removing the unit from the box as the Handle Assembly is attached to the unit by

cables.

PUT OIL IN ENGINE BEFORE STARTING

Boxing Parts Checklist

Handle Upper Assembly

Item 24 P/N-441408

Parts Bag & Literature Assy

P/N-441406

Vanguard 5.5

B&S XR950

PARTS BAG & LITERATURE ASSY

Warranty card P/N- 400972, Owner’s Manual P/N-441502, General Safety and Warnings Manual P/N-100294, Declaration of

Conformity P/N-441249

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

ASSEMBLY

1. First, attach the front wheel. The hardware

to secure the wheel (spacer, bolt, and nut)

are included with your unit. Gently lower

your Billy Goat ForceTM Blower onto its

back to access the front wheel bracket.

Insert the spacer into the front wheel. Then,

place the wheel into the front wheel

bracket. Line up the wheel axle holes with

the holes inthe bracket. Insert the bolt into

the bracket and front wheel, and then

secure the wheel with the nut provided.

Use 9/16” wrenches to tighten the

hardware and further secure the front

wheel assembly. See Figure 1. With the

front wheel attached, gently lift your Billy

Goat ForceTM Blower into operating

position. Chock the front wheel to keep the

unit from moving while you assemble the

handles.

2. Second, assemble the handles. Locate the

upper handle assembly hardware, two bolts

and two knobs. Line up the upper handle to

the lower handles. Secure the upper

handle to the lower handle with the bolt

and knob. Tighten by hand. Note that the

knob should be installed inside the handle

assembly. See Figure 2. Secure the

opposite side of the handle assembly with

the remaining bolt and knob.

3. Finally, connect the Aim-N-ShootTM cable.

One end of the Aim-N-ShootTM cable is

connected to the airdirector cone, but you

will need to connect the ball end of the

cable to the Aim-N-ShootTM control lever on

the upper handle. First, locate the rolled up

cable beneath the unit. Then unroll the

cable, thread the cable to the outside of the

machine and up to the handle. Push down

on the air director cone to release extra

length on the ball end of the cable. See

Figure 3. With the extra length released,

attach the Aim-N-ShootTM cable to its

holder on the Aim-N-ShootTM control lever.

See Figure 4. Finally, secure your Aim-N-

ShootTM cable to the unit with the zip ties

provided.

NOTE: All items referenced in ( ) can be found in the Illustrated Parts Drawing and Parts List found at the back of the

manual.

Fig. 1

Fig. 2

NOT FOR REPRODUCTION

OPERATION

BLOWING OPERATION

Your Billy Goat ForceTM blower isequipped with an air director cone and the patented Aim-N-ShootTM control lever to allow the

operator to direct the air stream up or down as required to assist in moving debris. This feature is extremely useful when debris

haspiled up to the point that it cannot be blown any farther. The air stream can be directed upward to blow the top of the debris

pile over and allow the operator to continue moving more debris farther.

ADJUSTING AIR DIRECTOR

To adjust airdirection, squeeze Aim-N-Shoot control lever.When you want to blow debris at the same angle for an extended

period, choose a suitable position and use the finger controlled push button lock to lock the cone in position. For operationsthat

do not require the use of the Aim-N-Shoot feature, themanual adjustment knob, pictured below, can be used to permanently lock

the cone into position. NOTE:be sure to release the knob when returning to using the Aim-N-Shoot (See Fig. 5).

DO NOT position director cone to where it will blow debris towards people, vehicles or other objects in vicinity. Flying debris

may damage, harm, or cause injury to people or objects in air flow range.

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

Manual

adjustment

knob

Fig. 5

Fig. 3

Fig. 4

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

MAINTENANCE

PERIODIC MAINTENANCE

Periodic maintenance should be performed at the following intervals:

Maintenance Operation Every Use Daily or Every 5 Hours Every 100-150 Hours

Inspect for worn or damaged parts 

Check for excessive vibration 

Inspect impeller for cracks or damage 

Inspect for loose parts 

IMPELLER REMOVAL

1. Wait for engine to cool and disconnect spark plug.

2. Remove housing front cover by removing the ten screws from around outside of front cover and the exhaust knob (item

#22) and nut (item #14).

3. Remove impeller bolt (item #29), lock washer (item #7) and washer (item #28).

4. DO NOT pry on impeller. Pull on center hub area only of impeller. If impeller slides off freely, proceed to (step 6).

5. If the impeller does not loosen, use a pry bar against the back of the hub and the plate and apply pressure to separate

the impeller from the shaft. DO NOT use the pry bar to apply pressure to any plastic part such as the impeller or the

main housing. Using a penetrating oil can help loosen a stuck impeller.

6. Reinstall new impeller in reverse order of removal.

7. Tighten impeller bolt. Torque impeller bolt (see Parts List on page 10 for proper impeller bolt torque specifications).

TIRE AIR PRESSURE

Check at regular intervals and maintain.

Rear Tires - 20 Psi (137 kPa).

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

TROUBLESHOOTING

*Using compressed air, or a backpack blower, you can

loosen or free debris easily from the impeller and housing,

which can cause wear and tear on the machine. You can

manually remove debris by taking off the front housing.

NOTE: Always disconnect the spark plug when servicing.

(See Fig. 4 and 5)

Fig. 6

Fig. 7

Problem Possible Cause Solution

Abnormal vibration Loose or out of balance impeller. Check impeller and replace if required.

Debris in impeller.

Clear debris with compressed air or a

backpack blower (See Fig . 6 and 7 below).*

Loose engine. Check engine.

Engine will not start Engine not in full choke position. Check choke position.

Out of gasoline or bad, old gasoline. Check gasoline.

Spark plug wire disconnected. Connect spark plug wire.

Gas valve off. Turn on gas valve.

Dirty air cleaner.

Clean or replace air cleaner. Contact a

qualified service person.

Engine is locked, will not pull

over

Engine problem.

Contact an engine servicing dealer for

engine problems.

Aim-N-Shoot

lever sticking Debris stuck around cone. Clean debis.

Cone adjustment knob too tight.

Apply silicone based lubricant to

Adaptor mount nut (item #43) too

pivot points.

tight. Loosen manual adjustment knob.

Loosen nut.

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

F601V and F601X PARTS DRAWING

NOT FOR REPRODUCTION

FORCETM 602V/X BLOWER Owner’s Manual

Part No 441502 441502_A_HI

F601V and F601X PARTS LIST

F602V F602X

ITE M NO. DESCRIPTION PART NUMBER QTY. PART NUMBER QTY .

1ENGINE, 160CC, VANGUARD 382351 1 - -

ENGINE B&S XR - - 441210 1

2BASE ENGINE WA 441151-S 1441151-S 1

3SCREW PLASTITE #8-16 X 3/4" HWH 441155 10 441155 10

4PLATE REINFORCE HOUSING 441102 2441102 1

5HOUSING FRONT MOLDED 441101-1-S 1441101-1-S 1

6HOUSING BACK MOLDED 441101-2 1441101-2 1

7WASHER LOCK 5/16 ST MED 8177011 58177011 5

8SCREW CAP 5/16-24 X 1" GR. 5 ZP 400164 4400164 4

9ROD HAND STOP 441154 1441154 1

10 WASHER 5/16 FLATWASHER Z/P 8171003 12 8171003 12

11 NYLON INSERT LOCKNUT 5/16-18 8160002 48160002 4

12 BOLT CARRIAGE 5/16-18 X 2" CONE HEAD ZP 80003918 280003918 2

13 SCREW PLASTITE 1/4-10 X 3/4 HWH 840082 4840082 4

14 NUT LOCK 5/16-18 LT WT TH ZP 8161041 18161041 1

15 RING RETAINING 3/4 850230 2850230 2

16 WHEEL 8" X 0.5 441123 1441123 1

17 SPACER FRONT AXLE 441162 1441162 1

18 WHEEL ASSY 10" 400295 2400295 2

19 FRONT WHEEL BRACKET 441122 1441122 1

20 SCREWCAP 3/8-16 X 3 3/4 HCS ZP 8041061 18041061 1

21 WASHER W/BOLT WA 441156 1441156 1

22 KNOB 5/16-18 X 5/8 FLUTED 400339 1400339 1

23 WASHER EXTENSION 810652 1810652 1

24 HANDLE UPPER 441157-S 1441157-S 1

25 HANDLE LOWER LH 441158 1441158 1

26 HANDLE LOWER RH 441159 1441159 1

27 NUT LOCK 3/8-16 LT WT THIN ZP 8161042 18161042 1

28 WASHER 1.125 OD X 0.344 ID X 10 GA. 441150 1441150 1

SCREWCAP 5/16-24 X 1 1/2 GR 8 24-28 Ft. lbs. (33-38 N.m.

830135 1830135 1

30 DIRECTOR CONE 3.5" 441120-01 1441120-01 1

31 SCREWCAP 5/16-18 X 2 1/2 8041034 48041034 4

32 IMPELLER ASSEMBLY 16" 441202-S 1441202-S 1

33 LABEL SPARK ARRESTOR 100252 1100252 1

34 LABEL WARNING FUEL EN/SP 100261 1100261 1

35 PLATE ENGINE XR 950 - - 441255 1

36 LABEL SAFETY PROTECT READ MANUAL 100346 1100346 1

37 LABEL DANGER FLYING DEBRIS 810736 1810736 1

38 GRIP 1" ID x 13" 400570 2400570 2

39 LABEL LOGO SMALL FRAME 441234 1441234 1

40 KEY 3/16" SQ x 1 3/4 9201084 19201084 1

41 SPACER ENGINE BRIGGS XR - - 441254 1

43 NUT LOCK 1/4"-20 HEX ZP 8160001 48160001 4

44 HANDLE DIVERTER FORCE 440119 1440119 1

45 PIN LATCH DIVERTER 440118 1440118 1

46 SPRING COMPRESSION 0.281 X 0.88 440129 1440129 1

47 RING RETAINING .122 DIA 440125 1440125 1

48 SADDLE LOWER DIVERTER 440115 1440115 1

49 PLATE LOCK DIVERTER 440116 1440116 1

50 SCREW PLASTITE #6-19 X 5/8" 440132 1440132 1

51 SADDLE UPPER DIVERTER 440114 1440114 1

52 SCREW PLASTITE #10-14 X 1" 440126 2440126 2

53 PIN PIVOT DIVERTER CONTROL 440123 1440123 1

54 RING RETAINING 5/16 430327 1430327 1

55 CABLE ASSY 441163 1441163 1

56 DIVERTER PIVOT ADAPTOR 440121 1440121 1

57 SPRING EXTENSION 0.468 X 5.25 440130 1440130 1

58 PIN CLEVIS 1/4 X 3/4 440124 1440124 1

59 .051 X 3/4" HITCH PIN CLIP 440193 1440193 1

60 ADAPTOR MOUNT WA 440122 1440122 1

61 TY-WRAP 900407 3900407 3

62 LABEL VIBRATION WARNING 440191 1440191 1

63 FORCE WHEEL BEARING .751 ID 440055 2440055 2

64 ELASTIC LOOP BLACK 5.5" 100267 1100267 1

65 SCREWCAP 1/4-20 X 1 1/4" HCS ZP 8041007 28041007 2

66 FENDER WASHER 5/16 8172020 48172020 4

67 WASHER 1/4" SAE 8172007 48172007 4

68 SCREWCAP 1/4"-20 1 1/2" HCS ZP 8041008 28041008 2

69 SCREWCAP #10-24 X 1 1/4" HWH ZP 8059140 18059140 1

70 WASHER #10 SAE 8172005 28172005 2

71 NUT LOCK LT #10 - 24 HEX 8164005 18164005 1

72 NUT LOCK 1/4"-20 2 WAY 8142004 18142004 1

73 LABEL AIM AND SHOOT 440332 1440332 1

74 KNOB, 5-LOBE 5/16"-18 FEMALE 441258 2441258 1

75 DIVERTER ASSY 440312 1440312 1

NOT FOR REPRODUCTION

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Billy Goat Ventilateur

Billy Goat

Billy Goat QUIET BLOW QB1004 Instructions d'installation

Billy Goat

Billy Goat KV600SP Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB1601 Instructions d'installation

Billy Goat

Billy Goat F902S Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB1601 Instructions d'installation

Billy Goat

Billy Goat QUIET BLOW QB1100HPN Manuel utilisateur

Billy Goat

Billy Goat F902S Manuel utilisateur

Billy Goat

Billy Goat F601S Manuel utilisateur

Billy Goat

Billy Goat HURRICANE X3000 Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB501CE Instructions d'installation

Billy Goat

Billy Goat QUIET BLOW QB554HC Manuel utilisateur

Billy Goat

Billy Goat 440021 Manuel utilisateur

Billy Goat

Billy Goat F902SPH Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB1004 Instructions d'installation

Billy Goat

Billy Goat MV VACUUM PUSH EU MV601EU Manuel utilisateur

Billy Goat

Billy Goat Force Blower Manuel utilisateur

Billy Goat

Billy Goat EX17D50012 Manuel utilisateur

Billy Goat

Billy Goat F1002SPV Manuel utilisateur

Billy Goat

Billy Goat Z FORCE FZ1300H Manuel utilisateur

Billy Goat

Billy Goat QUIET BLOW QB553 Instructions d'installation

Billy Goat

Billy Goat FORCE F601V Manuel utilisateur

Billy Goat

Billy Goat KV600SP Manuel utilisateur

Billy Goat

Billy Goat QB883, QB883H, QB1103, QB1103H Instructions d'installation

Billy Goat

Billy Goat F1302H Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

Weed Eater

Weed Eater VS2000BV Manuel utilisateur

KRAUSMANN

KRAUSMANN U37020-00 Manuel utilisateur

Bosch

Bosch ALB 36 LI Manuel utilisateur

Cub Cadet

Cub Cadet HB425 Manuel utilisateur

GreenWorks Pro

GreenWorks Pro BLB482 Manuel utilisateur

ARIETE

ARIETE 2768 Manuel utilisateur

NuTone

NuTone 331H Manuel utilisateur

GÜDE

GÜDE GLB 200 18 Li-Ion Manuel utilisateur

I.VA.CO.

I.VA.CO. SC Series Mode d'emploi

DeWalt

DeWalt DCE100 Manuel utilisateur

Becker

Becker SV 7.330 Manuel utilisateur

Metabo

Metabo AG 18 Pro Manuel utilisateur

Desa

Desa GA3650TB Manuel utilisateur

Echo

Echo Power Blower PB-230LN Manuel utilisateur

Echo

Echo PB-413H Manuel utilisateur

Black & Decker

Black & Decker BV3100 Manuel utilisateur

Ryobi

Ryobi RY08570 Manuel utilisateur

Haaga

Haaga 355 Manuel utilisateur