BGS technic 9235 Manuel utilisateur

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 9235

500 Kg Engine Support

GENERAL

The engine support allows the dismantling of front axle at front- and rear-wheel drive vehicles without

removing the drive unit. The engine support is also needed for gear repair and replacing the clutch on

front-wheel drive vehicles. By movable brackets and a hook, the engine support is suitable for

different vehicle types.

TECHNICAL DATA

Maximum load: 500 Kg

Width: 750 to 1450 mm

CAUTION

•Never exceed the recommended maximum carrying capacity of the engine support.

•Mount the safety chain only at points which can safely lift the load. (Check vehicle-specific

service literature for further information)

•Any additional shackles or other carrying/holding facilities need to match the engine support’s

dimensions and specifications. Oversizing is better!

•Before you hang a load on the engine support, check all components of the engine support for

proper working condition and secure that all screws are tight.

•Do not mount the chain in a twisted position. Make sure that the chain links are not jammed.

There is risk of bruising, as the jammed chain links may be released abruptly and the load will

be suddenly lowered several inches.

•Make sure that you align the tilt adjustment accurate and tighten the screw well.

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

D-42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

INSTRUCTION

The engine support must be assembled before first use. Start with

assembling at the brackets. These consist of two parts and are

coupled with a screw.

Place the two support parts together and tighten the screws on the

side manually.

Insert the bolt of the bracket into each side of the engine support.

Put a washer on top of the bolt and screw

them in place with the help of hand nuts on

the engine support.

Mount the two holding screws in the middle collet of the engine

support, place a washer on the holding screws and tighten the large

wing nuts a few turns on the holding screws.

Place the engine support with the bracket either on the fender’s

screwing edge or rather on the fender’s welding edge. Make sure that

both hand-locking screws of the alignment are tight.

Adjust the angle of engine support and fix the setting with the lateral

screws.

When the two fixing screws for adjusting the inclination and the hand-

locking screws of the bracket are tightened, the chains are attached to

the appropriate places on the engine or gearbox and mounted onto the

holding screws.

Screw the wing nuts (holding spindles) until the chains are pulled

under tension and the entire load hangs on the chain. A dismantling of

e.g. gear or axle parts is now possible.

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

CE-Erklärung

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected] www.bgstechnic.com

EU-KONFORMITÄTSERKLÄRUNG

EC DECLARATION OF CONFORMITY

DÉCLARATION„CE“ DECONFORMITE

DECLARATIONDE CONFORMIDADUE

Wir erklären in alleiniger Verantwortung, dass die Bauart des Produktes:

We declare that the following designated product:

Nous déclarons sous propre responsabilité que ce produit:

Declaramos bajo nuestra sola responsabilidad que este producto:

folgenden einschlägigen Bestimmungen entspricht:

complies with the requirements of the:

est en conformité avec les réglementations ci-dessous:

esta conforme a las normas:

Angewandte Normen:

,GHQWL¿FDWLRQRIUHJXODWLRQVVWDQGDUGV

Norme appliquée:

Normas aplicadas:

ppa.

Frank Schottke, Prokurist

BGS technic KG, Bandwirkerstrasse 3, D-42929 Wermelskirchen

Wermelskirchen, den

Motor-Traverse ( BGS Art. 9235 )

Engine Support

Traverse de moteur

Traviesa de motor

Machinery Directive 2006/42/EC

EN ISO 12100:2010

EN 1494:2000+A1:2008

Certificate No.: EC.1282.0B131230.ZZM3730/ZX0104-1A

Report: ZZM/TJ/TCF1.0(13)/MD

09.05.2016

Table des matières

Autres manuels BGS technic Équipement de service

BGS technic

BGS technic 9866 Manuel utilisateur

BGS technic

BGS technic 9638 Manuel utilisateur

BGS technic

BGS technic 8335 Manuel utilisateur

BGS technic

BGS technic BGS 7729 Manuel utilisateur

BGS technic

BGS technic 8957 Manuel utilisateur

BGS technic

BGS technic 70909 Manuel utilisateur

BGS technic

BGS technic 8640 Manuel utilisateur

BGS technic

BGS technic 1674 Manuel utilisateur

BGS technic

BGS technic 8697 Manuel utilisateur

BGS technic

BGS technic 70153 Manuel utilisateur

BGS technic

BGS technic 2851 Manuel utilisateur

BGS technic

BGS technic 6686 Manuel utilisateur

BGS technic

BGS technic 3501 Manuel utilisateur

BGS technic

BGS technic 8420 Manuel utilisateur

BGS technic

BGS technic 8546 Manuel utilisateur

BGS technic

BGS technic 40106 Manuel utilisateur

BGS technic

BGS technic 70110 Manuel utilisateur

BGS technic

BGS technic 70928 Manuel utilisateur

BGS technic

BGS technic 3001 Manuel utilisateur

BGS technic

BGS technic BGS 8702 Manuel utilisateur

BGS technic

BGS technic 7082 Manuel utilisateur

BGS technic

BGS technic 9327 Manuel utilisateur

BGS technic

BGS technic 9391 Manuel utilisateur

BGS technic

BGS technic 9234 Manuel utilisateur

Manuels Équipement de service populaires d'autres marques

CEMB

CEMB DWA1000CWAS Manuel utilisateur

Invacare

Invacare TDX SP Instructions de montage

MAHLE

MAHLE AIR-NEX 9310 Manuel utilisateur

Waeco

Waeco ASC 6300 G Manuel utilisateur

Multipick

Multipick MHP II Manuel utilisateur

FLO-DYNAMICS

FLO-DYNAMICS BrakeMate Jr Manuel de programmation

EDS

EDS LeekSeeker 89R Manuel utilisateur

Wen

Wen 73017T Manuel utilisateur

Sealey

Sealey VS820 Manuel utilisateur

OTC

OTC Genisys EVO Manuel utilisateur

Slime

Slime 50122 Manuel utilisateur

CAS

CAS LCH-TCR302 Manuel utilisateur

Matco Tools

Matco Tools R325HU Manuel utilisateur

Sealey

Sealey MS070CR Manuel utilisateur

CLAS

CLAS EG 0332 Manuel utilisateur

Boston

Boston AGS-200 Manuel utilisateur

Slime

Slime 40080 Manuel utilisateur

Waeco

Waeco AirCon Service 6300G Manuel utilisateur