Beward ST-811HP Manuel utilisateur

8-Port 10/100TX 802.3at PoE + 1-Port 10/100/1000T +

1-Port 100/1000X SFP Desktop Switch

ST-811HP

User’s Manual

publication may be reproduced, transmitted, transcribed, stored in a retrieval

system, or translated into any language or computer language, in any form or

by any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission of BEWARD.

BEWARD makes no representations or warranties, either expressed or implied,

with respect to the contents hereof and specically disclaims any warranties,

merchantability or tness for any particular purpose. Any software described

in this manual is sold or licensed "as is". Should the programs prove defective

following their purchase, the buyer (and not BEWARD, its distributor, or its dealer)

assumes the entire cost of all necessary servicing, repair, and any incidental or

consequential damages resulting from any defect in the software. Further, BEWARD

reserves the right to revise this publication and to make changes from time to time

in the contents hereof without obligation to notify any person of such revision or

changes.

All brand and product names mentioned in this manual are trademarks and/or

registered trademarks of their respective holders.

Trademarks

BEWARD is a registered trademark of BEWARD Co., Ltd.

All other trademarks belong to their respective owners

Disclaimer

BEWARD Technology does not warrant that the hardware will work properly in all

environments and applications, and makes no warranty and representation, either

implied or expressed, with respect to the quality, performance, merchantability, or

tness for a particular purpose.

BEWARD has made every effort to ensure that this User’s Manual is accurate;

BEWARD disclaims liability for any inaccuracies or omissions that may have

occurred. Information in this User’s Manual is subject to change without notice and

does not represent a commitment on the part of BEWARD. BEWARD assumes no

responsibility for any inaccuracies that may be contained in this User’s Manual.

BEWARD makes no commitment to update or keep current the information in this

User’s Manual, and reserves the right to make improvements to this User’s Manual

and/or to the products described in this User’s Manual, at any time without notice.

If you nd information in this manual that is incorrect, misleading, or incomplete,

we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the Instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not

dispose of WEEE as unsorted municipal waste and have to collect such WEEE

separately.

Revision

BEWARD 8-Port 10/100TX 802.3at PoE + 1-Port 10/100/1000T + 1-Port

100/1000X SFP Desktop Switch User's Manual

For Model: ST-811HP

Table Of Contents

1. Introduction ............................................................................................... 5

1.1 Checklist............................................................................................. 5

1.2 Product Description.............................................................................. 5

1.3 Features ............................................................................................. 6

1.4 Specications ...................................................................................... 7

2. Hardware Description .................................................................................. 9

2.1 Front Panel ......................................................................................... 9

2.1.1 LED Indicators ..........................................................................11

2.2 Rear Panel .........................................................................................11

3. Hardware Installation .................................................................................12

3.1 Desktop Installation ............................................................................13

3.2 Rack Mounting ...................................................................................14

3.3 Wall Mounting Installation ...................................................................15

4. Troubleshooting .........................................................................................17

Appendix A - 10/100Mbps, 10/100BASE-TX ......................................................18

1. Introduction

1.1 Checklist

Check the contents of your package for the following parts:

ST-811HP x 1 User’s Manual x 1

Power Cord x 1 Rubber Feet x 4

Rack-mounting Brackets Screws x 8

If any of these pieces are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing material,

and use them again to repack the product in case there is a need to return it to us

for repair.

1.2 Product Description

The ST-811HP, a new member in the BEWARD 802.3at PoE Fast Ethernet Switch

family, provides 8-port 10/100Mbps 802.3af/at Power over Ethernet, 1 Gigabit port

and 1 Gigabit SFP port with a total of 120 watts of PoE budget. Its PoE power

is more than enough for those network applications with Fast Ethernet speed

transmission. The eight 802.3af/at PoE ports feature PoE power injector function

which is able to drive 8 IEEE 802.3at compliant powered devices. The ST-811HP

also offers a simple, costeffective and nonblocking wirespeed performance. It

comes with a 9-inch metal compact housing, suitable for desktop deployment in

SOHO ofce or department network application.

The mini-GBIC slot built in the ST-811HP supports SFP auto-detection and dual

speed as it features 100BASE-FX and 1000BASE-SX/LX SFP (Small Form-factor

Pluggable) ber-optic modules, meaning the administrator now can exibly

choose the suitable SFP transceiver according to the transmission distance or the

transmission speed required to extend the network efciently.

1.3 Features

Physical Port

z8 10/100Mbps Fast Ethernet ports

z1 10/100/1000BASE-T Gigabit Ethernet port

z1 1000BASE-X mini-GBIC SFP interface

Power over Ethernet

zComplies with IEEE 802.3af/at Power over Ethernet end-span

zUp to 8 IEEE 802.3af/at devices powered

zSupports PoE Power up to 30 watts for each PoE port

z120-watt PoE budget

z8 ports support 52V DC power to PoE powered device (Port 1 to port 8)

zHardware DIP switch for “Standard”, “VLAN” and “Extend” mode selection; the

“Extend” mode features 30-watt PoE transmit distance of 250m at speed of

10Mbps and VLAN isolation

zAuto detects powered device (PD)

zCircuit protection prevents power interference between ports

zRemote power feeding up to 100m in standard mode

Switching

zHardware-based 10/100/1000Mbps auto-negotiation and auto MDI/MDI-X

zFlow control for full duplex operation and back pressure for half duplex opera-

tion

zIntegrates address look-up engine, supporting 4K absolute MAC addresses

zAutomatic address learning and address aging

zSolid DIP switch to isolate ports to prevent broadcast storm and defend DHCP

spoong

Hardware

z9-inch desktop size, 1U height, mountable

zLED indicators for PoE ready/activity and LINK/ACT

zFanless design

zInternal AC power supply

zSupports Energy-Efcient Ethernet (EEE) function (IEEE 802.3az)

1.4 Specications

Model ST-811HP

Hardware Specications

10/100Mbps Ports 8 10/100BASE-TX MDI/MDI-X RJ45 ports

Gigabit Ports 1 10/100/1000BASE-T MDI/MDI-X RJ45 port

SFP Slot 1 100/1000BASE-X SFP/mini-GBIC interface

PoE Inject Port 8-port with 802.3af/at PoE injector function

(Port-1 to Port-8)

LED Display

System:

Power (Green)

10/100BASE-TX RJ45 Interface:

PoE (Orange, Port-1 to Port-8)

LNK/ACT (Green, Port-1 to Port-8)

10/100/1000BASE-T RJ45 Interface:

1000Mbps LNK/ACT (Green, Port 9)

100/1000BASE-X SFP Interface:

1000Mbps LNK/ACT (Green, Port 10)

DIP Switch

100m distance in standard mode

250m distance in extend mode

(based on the cable category)

Switch Architecture Store and Forward switch architecture

MAC Address Table 4K MAC address table with auto learning function

Switch Fabric 5.6Gbps

Switch Throughput 4.16Mpps @64bytes

Maximum Packet Size 9K bytes

Flow Control Back pressure for half duplex; IEEE 802.3x pause

frame for full duplex

Power Requirements AC 100~240V, 2.5A max.

Power Consumption 135 watts, 463.2 BTU

Dimensions (W x D x H) 220 x 150 x 44 mm

Weight 1220 g

ESD Protection Contact discharge of ±6KV DC

Air discharge of ±8KV DC

Surge Immunity ±4KV

Power over Ethernet

PoE Standard IEEE 802.3af Power over Ethernet/PSE

IEEE 802.3at Power over Ethernet Plus/PSE

PoE Power Supply Type End-span

Power Pin Assignment 1/2(+), 3/6(-)

PoE Power Output

Per Port 52V DC, 600mA. max. 30 watts

(IEEE 802.3at)

Per Port 52V DC, 300mA. max. 15.4 watts

(IEEE 802.3af)

PoE Power Budget 120 watts

Number of PDs, 7 watts 8

Number of PDs, 15.4 watts 8

Number of PDs, 30 watts 4

Standards Conformance

EMI Safety CE, FCC

Standards Compliance

IEEE 802.3

IEEE 802.3u

IEEE 802.3ab

IEEE 802.3z

IEEE 802.3x

IEEE 802.3af

IEEE 802.3at

Ethernet

Fast Ethernet

Gigabit 1000BASE-T

Gigabit SX/LX

Flow Control

Power over Ethernet

Power over Ethernet Plus

Environment

Operating Environment 0 ~ 50 degrees C

Storage Environment -10 ~ 70 degrees C

Operating Humidity 5 ~ 95%, relative humidity, non-condensing

Storage Humidity 5 ~ 95%, relative humidity, non-condensing

2. Hardware Description

The switch provides three different running speeds – 10/100/1000Mbps, and

automatically distinguishes the speed of the incoming connection.

This section describes the hardware features of the ST-811HP. For easier

management and control of the ST-811HP, familiarize yourself with its display

indicators and ports. Front panel illustrations in this chapter display the unit LED

indicators. Before connecting any network device to the ST-811HP, please read this

chapter carefully.

2.1 Front Panel

The front panel of the ST-811HP PoE+ Ethernet Switch consists of 8 auto-sensing

10/100Mbps Ethernet RJ45 ports, 1 auto-sensing 10/100/1000Mbps Ethernet RJ45

port and 1 auto-sensing 10/100/1000 Mbps SFP port. The LED indicators are also

located on the front panel of the ST-811HP.

4 6 82

1 3 5 7 9

PWR

Gigabit

53 7

2 6

4 8

9 10

PoE

8-Port 10/100TX 802.3at PoE+1-Port Gigabit+

1-Port Gigabit SFP Desktop Switch

PoE In-Use

ACTLNK

1000

ACTLNK

Standard

VLAN

Extend 10

Uplink

Figure 2-1: ST-811HP Switch Front Panel

The front panel of the ST-811HP provides one DIP switch for Standard, VLAN and

Extend mode selections. The detailed descriptions are shown in the following table.

DIP Switch Mode Function

Standard

VLAN

Extend

This mode makes the ST-811HP operate as a general switch

and all PoE ports operate at 10/100Mbps auto-negotiation.

Standard

VLAN

Extend

This mode makes the ST-811HP operate as a VLAN isolation

switch and

1.Port 1 to port 8 will isolate respectively.

2.Port 1 to port 8 can only communicate with port 9 and port

10 (uplink port).

Standard

VLAN

Extend

This mode makes the ST-811HP operate as an Extend and

VLAN isolation switch and

1.Port 1 to port 8 will isolate respectively

2.Port 1 to port 8 can only communicate with port 9 and port

10 (uplink port).

3. 30-watt PoE transmit distance of 250m at speed of 10Mbps.

Note

Please reboot the ST-811HP after adjusting the DIP switch to take

effect.

Standard Mode (default)

Power

PoE IP Camera

PoE

100 meters (328 feet)

ST-811HP

PoE

100BASE-TX UTP with PoE

Standard

VLAN

Extend

VLAN Isolation Mode

NVR

Ports 1 to 8

Access Denied

PoE

100BASE-TX UTP with PoE

ST-811HP

IP Camera

Standard

VLAN

Extend

Port 9 and 10

To Port 1~8 Access Permitted

1000BASE-T UTP

Extend Mode

Power

250 meters (820 feet)

PoE

10BASE-T UTP with PoE

ST-811HP PoE IP Camera

Standard

VLAN

Extend

Table des matières

Autres manuels Beward Changer

Beward

Beward ST-810P Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur