Bertazzoni KIN70MOD1XB Manuel utilisateur

COOKER HOOD - Instructions Manual

KIN70MOD1XB

KIN52MOD1XC

KIN86MOD1XB

INDEX

SAFETYINFORMATION......................................................................................................................................................... 3

CHARACTERISTICS.............................................................................................................................................................6

INSTALLATION...................................................................................................................................................................... 7

USE........................................................................................................................................................................................ 9

CAREANDCLEANING.........................................................................................................................................................10

EN 3

SAFETY INFORMATION

For your safety and correct operation of the appliance, read this manual

carefully before installation and use. Always keep these instructions

with the appliance even if you move or sell it. Users must fully know the

operation and safety features of the appliance.

The wire connection has to be done by specialized technician.

 The manufacturer will not be held liable for any damages resulting from

incorrect or improper installation.

 The minimum safety distance between the cooker top and the extractor

hood is 650 mm (some models can be installed at a lower height,

please refer to the paragraphs on working dimensions and installation).

 If the instructions for installation for the gas hob specify a greater

distance, this must be respected.

 Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

 Means for disconnection must be incorporated in the fixed wiring in

accordance with the wiring rules.

 For Class I appliances, check that the domestic power supply

guarantees adequate earthing.

 Connect the extractor to the exhaust flue through a pipe of minimum

diameter 120 mm. The route of the flue must be as short as possible.

 Regulations concerning the discharge of air have to be fulfilled.

 Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc.).

EN 4

 If the extractor is used in conjunction with non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of aeration must be

guaranteed in the room in order to prevent the backflow of exhaust gas.

When the cooker hood is used in conjunction with appliances supplied

with energy other than electric, the negative pressurein the room must

not exceed 0,04 mbar to prevent fumes being drawn back into the room

by the cooker hood.

 The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels.

 If the supply cord is damaged, it must be replaced from the manufac-

turer or its service agent.

 Connect the plug to a socket complying with current regulations, lo-

cated in an accessible place.

 With regards to the technical and safety measures to be adopted for

fume discharging it is important to closely follow the regulations pro-

vided by the local authorities.

WARNING: Before installing the Hood, remove the protective films.

 Use only screws and small parts in support of the hood.

WARNING: Failure to install the screws or fixing device in accordance

with these instructions may result in electrical hazards.

 Do not look directly at the light through optical devices (binoculars,

magnifying glasses…).

 Do not flambè under the range hood; risk of fire.

 This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in a safe way and under-

stand the hazards involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without

supervision.

 Children should be supervised to ensure that they do not play with the

appliance.

EN 5

 The appliance is not to be used by persons (including children) with re-

duced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction.

Accessible parts may become hot when used with cooking appliances.

 Clean and/or replace the Filters after the specified time period (Fire

hazard). See paragraph Care and Cleaning.

 There shall be adequate ventilation of the room when the range hood is

used at the same time as appliances burning gas or other fuels (not

applicable to appliances that only discharge the air back into the room).

 The symbol on the product or on its packaging indicates that this

product may not be treated as household waste. Instead it shall be

handed over to the applicable collection point for the recycling of elec-

trical and electronic equipment. By ensuring this product is disposed of

correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by

inappropriate waste handling of this product. For more detailed informa-

tion about recycling of this product, please contact your local city office,

your household waste disposal service or the shop where you pur-

chased the product.

EN 6

CHARACTERISTICS

Dimensions

500 mm 650 mm

Components

Ref. Q.ty Product Components

11 Hood Body, complete with :Controls, Light, Blower,

Filters

21 Frame

81 Directioned grid

9 1 Reducer Flange ø 150-120 mm

Ref. Q.ty Installation Components

12a 10 Screws

12e 2 Screws 2,9 x 9,5

12f 6 Screws 2,9 x 6,5

Q.ty Documentation

1 Instruction Manual

812e

12f

EN 7

INSTALLATION

Fitting the Hood canopy

BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:

• Disconnect the wires to the Commands at the connectors.

•Disconnect the wires to the Light at the con-

nectors.

• The Hood can beinstalled directly on the underside

of the wall unit.

•Create an opening in the bottom of the wallunit, as

shown.

•Insert the hood until the side supports snap into

place.

• Fasten using the 10 screws 12a provided.

•Lock in position by tightening thescrews Vf from

underneath the hood.

•Open the suction panel by pushing the lever.

• Disconnect the panel from the hood canopy by sliding the

fixing pin lever.

•Remove grease filters.

• Screw the Frame into place

using the 6 screws 12f, re-

connect the wires to the

Commands and Light, re-

place the metal grease filter

and the Panel.

260

495 - 675 - 835

EN 8

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to

the chimney using either a flexible or rigid pipe ø 150

or 120 mm, the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection, insert

the reducer flange 9on the hood body outlet.

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

• Remove possible charcoal filters.

ø 150

ø 120

RECIRCULATION VERSION AIR OUTLET

• Cut a hole ø 125 mm in any shelf that may be posi-

tioned over the hood.

• Insert the reducer flange 9on the hood body outlet.

• Connect the flange to the outlet on the shelf over the

hood by using a flexible or rigid pipe ø120 mm.

• Fix the pipe in position using sufficient pipe clamps

(not supplied).

• Fix the air outlet grid 8on the recirculation air outlet

by using the 2 screws 12e (2,9 x 9,5) provided.

• Ensure that the activated charcoal filters have been

inserted.

ø 125

12e

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm..

• Charcoal filters are sold separately.

EN 9

T1 T2 T3 T4

LT3

T1 T4

USE

Control panel

Button Led Function

L- Turns the lights on/off at maximum strength.

T1 Fixed Turns the motor on/off at speed one.

Fixed Turns the Motor on at speed two.

- Press and hold the button for approximately 3 seconds, with all the loads turned

off (Motor and Lights), to turn the Activated Charcoal Filter alarm on. The

relevant LED flashes twice to confirm.

To turn the alarm off, press the button again and hold for at least 3 seconds. The

relevant LED flashes once.

Fixed Turns the Motor on at speed three.

- Press and hold the button for approximately 3 seconds, with all the loads turned

off (Motor and Lights), to perform a reset of Filter saturation alarm. The LED S1

flashes three times.

Fixed Turns the Motor on at INTENSIVE Speed.

This speed is timed to run for 6 minutes. At the end of this time, the system

returns automatically to the speed that was set before. If it is activated with the

motor turned off, the hood will switch to OFF at the end of the time.

- Press and hold for 3 seconds to enable the remote control, indicated by the LED

flashing twice.

Press and hold for 3 seconds to disable the remote control, indicated by the LED

flashing just once.

Fixed Signals the Metal Grease Filter saturation alarm, indicating that it is necessary to

wash the filters. The alarm is triggered after the Hood has been in operation for

100 working hours.

Flashing When this is activated, it signals the Activated Charcoal Filter saturation alarm,

indicating that the filter must be changed; the Metal Grease Filters must also be

washed. The Activated Charcoal Filter saturation alarm comes

into operation after the Hood has been working for 200 hours.

EN 1

CARE AND CLEANING

REMOTECONTROL (OPTIONAL)

This appliance can be commanded using a remote control, powered by a

CR2032 type 3 V battery (not supplied).

• Do not place the remote control near heat sources.

• Do not discard the batteries with normal waste, they must be put into the

specific containers.

Opening Panel

• Open the Panel by pulling it.

• Clean the outside with a damp cloth and neutral detergent.

• Clean the inside using a damp cloth and neutral detergent; do not

use wet cloths or sponges, or jets of water; do not use abrasive

substances.

Metal grease filters

These can be washed in the dishwasher, and need to be cleaned

whenever the S1 Led comes on or at least once every 2 months use,

or more frequently if use is particularly intensive.

CLEANING THE FILTERS

Resetting the alarm signal

• Turn the Lights and the Suction Motor off.

• Press T3 and hold for at least 3 seconds, until LED flashes three

times in confirmation.

Cleaning the Filters

• Open the panel.

•Remove the Filter, pushing it towards the back of the unit and at

the same time pulling downward.

•Wash the filter without bending it, and leave it to dry thoroughly

before replacing (if the surface of the filter changes colour over

time, this will have absolutely no effect on its efficiency).

•Replace, taking care to ensure that the handle faces forwards.

•Close the panel again.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bertazzoni hotte de ventilation

Bertazzoni

Bertazzoni KIN 30 PER X Manuel utilisateur

Bertazzoni

Bertazzoni KGI90CONXA Instructions de fonctionnement

Bertazzoni

Bertazzoni KR70HER1NEDA Manuel utilisateur

Bertazzoni

Bertazzoni KI BI 120 NE A Instructions de fonctionnement

Bertazzoni

Bertazzoni KT Series Manuel utilisateur

Bertazzoni

Bertazzoni KU120PRO1XA Manuel utilisateur

Bertazzoni

Bertazzoni KT90MAS1NEC Manuel utilisateur

Bertazzoni

Bertazzoni Master Series Manuel utilisateur

Bertazzoni

Bertazzoni KMC30X Manuel du propriétaire

Bertazzoni

Bertazzoni Professional Series Manuel utilisateur

Bertazzoni

Bertazzoni KU24PRO1X/14 Manuel utilisateur

Bertazzoni

Bertazzoni K71FMHT2XN.UA Manuel utilisateur

Bertazzoni

Bertazzoni KTE60MOD1B Manuel utilisateur

Bertazzoni

Bertazzoni KV90MOD1NA Manuel utilisateur

Bertazzoni

Bertazzoni K41FMHT2XN.UA Manuel utilisateur

Bertazzoni

Bertazzoni KC90PRO1XA Manuel utilisateur

Bertazzoni

Bertazzoni KT90MAS1NEB Manuel utilisateur

Bertazzoni

Bertazzoni K90AMHXA/19 Instructions de fonctionnement

Bertazzoni

Bertazzoni KOTR24MXE Manuel utilisateur

Bertazzoni

Bertazzoni KTV30XV Manuel du propriétaire

Bertazzoni

Bertazzoni KU24 PRO 1XV Manuel utilisateur

Bertazzoni

Bertazzoni KU30 PRO 1XV Manuel utilisateur

Bertazzoni

Bertazzoni KT90PRO1XA Manuel utilisateur

Bertazzoni

Bertazzoni K24 PROX X Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur