BENDIX SmarTire Manuel utilisateur
Full Function Display
User’s Manual
SmarTire Systems Inc. reserves the right to change the contents of this manual at any time
and without notice. The information contained in this manual is proprietary and must not be
reproduced without prior consent from SmarTire Systems Inc.
© 2001 SmarTire Systems Inc.
1
TABLE OF CONTENTS
Notices 3
FCC Notice 3
European Regulations 4
System Scope of Use and Warnings 5
The SmarTire®System and Tire Maintenance 5
System Installation and Usage 5
Warnings 5
Introduction 6
Full Function Display Features 6
Power Stages 7
Full Function Display Controls and Indicators 7
Operation 8
Getting Started 8
Checking Tire Conditions 9
Alerts and Warnings 10
Pressure Deviation Alert 10
Low Pressure Warning 11
High Temperature Alert 11
Programming 12
To Enter Programming Mode 12
Display Icons 12
Operating Settings –Level 1 13
Cold Inflation Pressure 13
Low-Pressure Warning 14
2
SMARTIRE SYSTEMS INC.
Pressure Deviation Alert 15
Understanding Temperature Compensated Pressure Readings 16
High Temperature Alert 17
Metric or Imperial Measurement Selection 18
Tire Rotation 19
Advanced Programming –Level 2 21
Slope 21
Learn 22
Receiver Programming Mode –Level 3 25
Low Pressure Alert 25
Installation and Service 26
Installation 26
Full Function Display Specifications 27
Service and Warranty 28
System Diagnostics 28
Troubleshooting 28
Replacing a Full Function Display 29
Part numbers 29
US Warranty 29
Canadian Warranty 31
European Warranty 32
3
Notices
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device without the express approval of SmarTire
Systems Inc. may void the userís authority to use this device.
4
SMARTIRE SYSTEMS INC.
EUROPEAN REGULATIONS
This device complies with all European Electromagnetic compatibility regulations
(95/54 /EC and EN300 220-1). The equipment has been tested and found to comply
with the above regulations, and in addition it meets the requirements for low
powered transmitters/receivers as defined by the relevant radio approval authority.
The regulations are designed to provide reasonable protection against harmful
interference or susceptibility. Changes made to this device without the express
approval of SmarTire Europe Ltd. may void the user’s authority to use this device.
5
SYSTEM SCOPE OF USE AND WARNINGS
The SmarTire
®
System and Tire Maintenance
This system is a sensing device designed to identify and display tire operating data
and activate an alert or warning when pressure or temperature irregularities are
detected. It is the responsibility of the driver to react promptly and with discretion
to alerts and warnings. Abnormal tire inflation pressures should be corrected at
the earliest opportunity.
System Installation and Usage
Use of the SmarTire
®
system requires that it has been properly installed and
programmed by qualified personnel according to SmarTire Systems Inc. documentation.
This includes the Owner s Manual and any supplementary installation instructions
included with system components.
Warnings
1. When an alert or warning conditions is detected, reduce vehicle speed to an
appropriate safe level and proceed to a safe stopping location or facility where
the tire can be inspected and serviced.
2. The pressure deviation alert indicates that the pressure has dropped a selected
amount below the required pressure for that level of tire temperature.
3. The low pressure warning indicates that the air pressure has dropped to a
selected minimum.
4. The high temperature warning indicates that the contained air temperature has
exceeded the selected maximum. A tire temperature buildup can be caused by a
number of factors including severe under inflation, hard sustained braking,
vehicle overload and sustained high speeds.
Introduction
FULL FUNCTION DISPLAY FEATURES
The Full Function Display adds additional features to a previously installed SmarTire
system (refer to the Tire Pressure Monitoring System Owner’s Manual ). It provides
digital tire pressure and temperature data for up to 20 tire positions as well as
enabling warning level adjustment to suit driver needs.
The system’s modular design offers two digital display units. One clips onto the basic
receiver, while the other can be remotely located with an interconnecting cable.
6
SMARTIRE SYSTEMS INC.
F
ULL
F
UNCTION
D
ISPLAY
F
ULL
F
UNCTION
R
EMOTE
D
ISPLAY
7
POWER STAGES
The Full Function Display has an energy saving feature that turns lights on to full
intensity (Active stage) only when required to display alert conditions or program
the unit. The unit automatically switches to lower power stages when no control
activity is detected.
Full Function Display Controls and Indicators
Low pressure warning
Alarm light
TIRE button
MODE button
Alert indicator
Learn mode
Set button
Towing vehicle indicator
Units of pressure or
temperature
Tire rotation program
Cold pressure program
Programming mode
Numerical display
Programmed wheel position
No data
Data received
8
SMARTIRE SYSTEMS INC.
Operation
GETTING STARTED
Mount the display unit and connect to power source.
When power is applied to the receiver, the Full
Function Display momentarily turns on all icons,
beeps, and the alarm light blinks once. The unit
then goes into stand-by mode waiting for data
from the wheel transmitters.
Until the vehicle is in motion no data will be
received from any installed transmitter. The
display will remain blank as shown.
The respective tire icon is filled in as soon as data
from its transmitter is received. The windshield/
louver is shown for any towing vehicle transmitter.
After data from all transmitters is received the
display will be in the state shown at left until an
alert or warning condition is detected.
(Normal Mode)
Data from a towed vehicle is indicated by tire
icons with no windshield/louver icon.
Note: The system will alternate views between
the towing and towed vehicle when operating
with this configuration.
Autres manuels pour SmarTire
3
Table des matières
Autres manuels BENDIX Accessoires automobiles
BENDIX
BENDIX Bendix Wingman Advanced Manuel utilisateur
BENDIX
BENDIX Sheppard Instructions de montage
BENDIX
BENDIX AUTOVUE FLC-20 Instructions de montage
BENDIX
BENDIX VORAD VS-400 Manuel utilisateur
BENDIX
BENDIX VORAD VS-500 Manuel utilisateur
BENDIX
BENDIX Bendix Wingman ACB Instructions de montage
BENDIX
BENDIX VORAD VS-400 Manuel d'installation et d'exploitation
BENDIX
BENDIX BlindSpotter BW2860 Guide de configuration
BENDIX
BENDIX TABS-6 TRAILER ABS MODULE Instructions de montage
BENDIX
BENDIX ACTIVE STEERING SYSTEM Manuel utilisateur
BENDIX
BENDIX Wingman FLR20 Manuel utilisateur
BENDIX
BENDIX TLV-9000 Instructions de montage
BENDIX
BENDIX ADB22X-V Instructions de montage
BENDIX
BENDIX SmarTire Manuel utilisateur
BENDIX
BENDIX Intellipark Manuel utilisateur
BENDIX
BENDIX Gen. 4 ABS ECU Manuel utilisateur
BENDIX
BENDIX TC-2 Manuel utilisateur
