Bend-Pak HD-973PX Manuel utilisateur

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Tel: (805) 933-9970

bendpak.com

Multi-Level Parking Lift

Installation and Operation Manual

Manual P/N 5900076 — Manual Revision B2— January 2021

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

Read the

entire

contents of this manual

before

using this product.

Failure to follow the instructions and safety precautions in this manual can

result in serious injury or death. Make sure all other operators also read

this manual. Keep the manual near the product for future reference.

By proceeding with installation and operation, you agree

that you fully understand the contents of this manual and

assume full responsibility for product use

Model:

•HD-973P

•HD-973PX

Manual. HD-973P Series Multi-Level Parking, Installation and Operation Manual, Manual P/N 5900076, Manual

Revision B1, Released January 2021.

agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain

any rights to this content, and you will not use the copies for commercial purposes.

Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for identification only. All trademarks and registered trademarks mentioned

in this manual are the property of their respective owners.

Limitations. Every effort has been made to make sure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

You can always find the latest version of the manual for your product on the BendPak website.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for

full warranty details.Go to bendpak.com/support/register-your-product/ and fill out the online form to register

your product (be sure to click Submit).

Safety.Your product was designed and manufactured with safety in mind. However, your safety also depends

on proper training and thoughtful operation. Do not install, operate, maintain, or repair the unit without reading and

understanding this manual and the labels on the unit;

do not use your Lift unless you can do so safely!

Owner Responsibility. In order to maintain your product properly and to ensure everyone’s safety, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all installation, operation, and maintenance instructions.

• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,

such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions; keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain that all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as specified.

• Service and maintain the unit with approved replacement parts only.

• Keep instructions permanently with the product

and make sure all labels are clean and visible.

• Only use the Lift if it can be used safely!

Unit Information. Enter the Model Number, Serial

Number, and the Date of Manufacture from the label

on your unit. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture:

HD-973P Multi-Level Parking Lift 3P/N 5900076 — Rev. B2 — January 2021

Table of Contents

Introduction 3 Operation 68

Shipping Information 4 Maintenance 73

Safety Considerations 4 Troubleshooting 75

Components 6 Wiring Diagrams 76

Specifications 8 Labels 79

FAQ 11 Parts Drawings 81

Installation Checklist 12 Maintenance Log 89

Installation 13

Introduction

This manual describes the following BendPak Parking Lift:

•HD-973P: Multi-Level Parking Lift that can raise Vehicles up to 7,000 lbs (3,175 kg) on the Upper

Platform and up to 9,000 lbs (4,082 kg) on the Lower Platform.

•HD-973PX: A taller version of the HD-973P with

higher rise

and

extended

Runways

This manual is mandatory reading for all users of the HD-973P series, including anyone who installs,

uses, maintains, repairs, or wants to know more about them.

⚠DANGER Use care when installing, operating, maintaining, or repairing this equipment; failure

to do so could result in property damage, product damage, injury, or (in very rare

cases) death. Make sure only authorized personnel operate this equipment. All

repairs must be performed by an authorized technician. Do not make modifications

to the unit; this voids the warranty and increases the chances of injury or property

damage. Make sure to read and follow the instructions in this manual and on the

labels on the unit.

Keep this manual on or near the equipment so that anyone who uses or services it can read it.

If you are having issues, refer to the Troubleshooting section of this manual for assistance.

Technical support and service is available from your dealer, on the Web at bendpak.com/support,

by email at support@bendpak.com, or by phone at (800) 253-2363, extension 196. You may

also contact BendPak for parts replacement information at (800) 253-2363, extension 191; please

have the model and serial number of your unit available.

HD-973P Multi-Level Parking Lift 4P/N 5900076 — Rev. B2 — January 2021

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect

the shipment

before

you sign to acknowledge that you received it.

When you sign a bill of lading, it tells the carrier that the items on the invoice were received in good

condition.

To protect yourself, do not sign until

after

you have inspected the shipment.

If any of

the items listed on the bill of lading are missing or are damaged, do not accept the shipment until the

carrier makes a notation on the bill of lading that lists the missing and/or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.

It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs, if available.

Our willingness to assist in helping

you process your claim does not make us responsible for collection of claims or

replacement of lost or damaged materials.

Safety Considerations

Read this entire manual carefully before installing or using the product

.Do not

install or operate the product until you are familiar with all operating instructions and warnings. Do not

allow anyone else to operate it until they are familiar with all operating instructions and warnings. Keep

this manual on or near the product for future reference.

Read and follow the warnings and instructions on the labels on the product. Contact BendPak at

(800) 253-2363 or support@bendpak.com if you need replacement labels or a replacement

manual.

Safety Information

The following safety information applies to the HD-973P:

•The product is a Multi-Level Parking Lift; this Lift may be different from other Parking Lifts

you have installed or used. Use it only for its intended purpose.

•BendPak recommends referring to the ANSI/ALI ALIS Standard (R2015) Safety Requirements for

Installation and Service for more information about safely installing, using, and servicing your Lift.

•You must wear OSHA-approved (publication 3151) personal protective equipment at all times

when installing, using, maintaining, or repairing the Lift: leather gloves, steel-toed work boots, eye

protection, back belts, and hearing protection are

mandatory

•The product may only be operated by authorized, trained persons.

•When the Lift is in use, keep all body parts well away from it.

•Do not make any modifications to the Lift; this voids the warranty and increases the chances of

injury or property damage.

•Make sure all operators read and understand this Installation and Operation Manual. Keep the

manual near the Lift at all times.

HD-973P Multi-Level Parking Lift 5P/N 5900076 — Rev. B2 — January 2021

•Make an inspection of the Lift

before

using it. Check for damaged, worn, or missing parts. Do not

use it if you find any of these issues. Instead, take it out of service, then contact an authorized

repair facility, your dealer, or BendPak at (800) 253-2363 or support@bendpak.com.

•BendPak recommends making a

thorough

inspection of the product at least once a year.

Replace any damaged or severely worn parts, decals, or warning labels.

Symbols

Following are the symbols used in this manual:

⚠DANGER Calls attention to an immediate hazard that will result in death or severe injury.

⚠WARNING Calls attention to a hazard or unsafe practice that could result in death or severe

personal injury.

⚠CAUTION Calls attention to a hazard or unsafe practice that could result in minor personal

injury, product damage, or property damage.

NOTICE Calls attention to a situation that, if not avoided, could result in product or property

damage.

Tip Calls attention to information that can help you use your product better.

Liability Information

BendPak Inc. assumes no liability for damages resulting from:

• Use of the equipment for purposes other than those described in this manual.

• Modifications to the equipment without prior, written permission from BendPak.

•Injury or death caused by modifying, disabling, overriding, or removing safety features.

• Damage to the equipment from external influences.

• Incorrect operation of the equipment.

HD-973P Multi-Level Parking Lift 6P/N 5900076 — Rev. B2 — January 2021

Components

The main components of your Lift include:

•Power Post. The Post that holds the Power Unit. Mount the Power Unit on one of the two

Mounting Brackets.

•Power Unit. An electric/hydraulic unit that connects to an electric power source and then

provides Hydraulic Fluid to the Hydraulic Cylinder that raises and lowers the Runways.

•Flex Tubes. Not shown. A flexible, black tube that attaches to an opening on the Powerside

Runway on one end and to the Power Unit on the other end. Used for protecting the Return Line,

Air Line, and Hydraulic Hose (and Microswitch Cable for Upper Platform) as they are routed to the

Power Unit. One Flex Tube per Platform.

•Upper Platform. Can hold Vehicles up to 7,000 lbs (3,175 kg).

•Lower Platform. Can hold Vehicles up to 9,000 lbs (4,082 kg).

•Powerside Runway. On the same side as the Power Post (holds the Power Unit). The

Powerside Runway has the Hydraulic Cylinder and the Cables under it. Same for both Platforms.

•Offside Runway. The other Runway. It does not have a Hydraulic Cylinder or Cables under it.

Same for both Platforms.

•Aluminum Decks. Sits in between the two Runways. Protects any leakage from falling onto the

Vehicle below. Two per Platform.

•Safety Shutoff Bar. Located on the underside of the Upper Platform. The Safety Shutoff Bar

stops upward movement of the Lift. If you are raising a Vehicle on the Lower Platform and it hits

the Safety Shutoff Bar, the Lift immediately stops moving.

•Crosstubes. Each Platform has one at each end of the Lift. The Crosstubes are hollow; the

Cables that raise and lower the Runways are routed through the Crosstubes. The Crosstubes are

not interchangeable: Each Crosstube has an opening (called a ‘Window’) that faces the inside.

Windows open to the inside of the Lift only

•Crossbeams. Extra structural stability for your Lift. Two Crossbeams connect the Powerside

Posts and another two connect the Offside Posts.

•Crossbeam Brackets. Holds the Crossbeams in place, two per Post. Brackets

must

face the

inside of the Lift.

•Drive-up Ramps. The Upper Platform uses a longer set of Ramps, and the Lower Platform uses

a shorter set of Ramps. Use them to drive onto and off of the Runways. Two per Platform.

•Tire Stops. Located at the Front of the Lift, Tire Stops prevent the Vehicle’s Front Tires from

going any further forward. Additionally, we recommend that you chock the Vehicle’s Rear Tires.

Two per Platform.

•Safety Locks. Once engaged, they hold the Runways in position, even if the power goes out or

there is a leak in the Hydraulic Hoses. Your Lift has two columns of Safety Locks per post, spaced

every four inches. This lets you lock the Runways at just the right height for what you want to do.

Only leave your Lift on the ground or engaged on a Safety Lock.

•Platform Selector Valve. Controls which Platform is in operation; only

one

Platform can be

raised or lowered at a time.

•Pushbutton Air Valve. Moves the Safety Locks away from the Ladder so that they do not

engage as you lower the Lift. Used to lower the Runways.

•Ladders. Pieces of steel that gets installed at the back of each Post; these are part of the Safety

Lock system.

HD-973P Multi-Level Parking Lift 7P/N 5900076 — Rev. B2 — January 2021

The Front of the Lift is the end opposite the Drive-up Ramps. Front view.

HD-973P Multi-Level Parking Lift 8P/N 5900076 — Rev. B2 — January 2021

Specifications

Side View

Top View

HD-973P Multi-Level Parking Lift 9P/N 5900076 — Rev. B2 — January 2021

HD-973P Upper Platform Lower Platform

Lifting capacity 7,000 lbs / 3,175 kg 9,000 lbs / 4,082 kg

aTotal width 110.5" (9.3 feet) / 2,806 mm

b Total length (includes Ramps) 242" (20.2 feet) / 6,137 mm 200" (16.8 feet) / 5,080 mm

cOutside length 198" (16.6 feet) / 5,024 mm

dHeight of post 158" (13.2 feet) / 4,010 mm

eDrive-thru clearance 87" (7.3 feet) / 2,201 mm

fMaximum rise 139.5" (11.8 feet) / 3,544 mm 67.5" (5.8 feet) / 1,713 mm

gMaximum lifting height 145" (12.1 feet) / 3,681 mm 75" (6.3 feet) / 1,906 mm

hDistance between posts 100" (8.4 feet) / 2,541 mm

iRunway width 19" / 482 mm

jWidth between runways 35" – 41"/ 887 – 1,045 mm

kRunway length 188.5" (15.8 feet) / 4,786 mm 176" (14.8 feet) / 4,474 mm

lHeight of Platform when lowered 10.75" / 270 mm 5" / 127 mm

Top Safety Lock 144" (12 feet) / 3,656 mm 72" (6 feet) / 1,839 mm

Min. wheelbase @ rated capacity 1135" (11.3 feet) / 3,429 mm 125" (10.5 feet) / 3,175 mm

Min. wheelbase @ 75 capacity 1115" (9.7 feet) / 2,921 mm 105" (8.9 feet) / 2,667 mm

Min. wheelbase @ 50 capacity 195" (7.11 feet) / 2,413 mm 85" (7.1 feet) / 2,159 mm

Min. wheelbase @ 25 capacity 180" (6.8 feet) / 2,032 mm 70" (5.10 feet) / 1,778 mm

Safety Locks 31

Spaced every 4" / 102 mm

Lifting time 90 seconds 50 seconds

Motor 220 VAC, 60 Hz, 1 Ph (special voltages available upon request)

1 The Runways supports less weight than its rated capacity if the Vehicle’s wheelbase is shorter

because the wheels of such a Vehicle are closer to the middle of the Runways, where there is less

strength. For example, the maximum weight allowed on the Top Platform for a Vehicle with a

wheelbase of 95" is 50 percent of the Top Platform’s rated capacity (or 3,500 lbs when the rated

capacity is 7,000 lbs).

Specifications subject to change without notice.

HD-973P Multi-Level Parking Lift 10 P/N 5900076 — Rev. B2 — January 2021

HD-973PX Upper Platform Lower Platform

Lifting capacity 7,000 lbs / 3,175 kg 9,000 lbs / 4,082 kg

aTotal width 110.5" (9.3 feet) / 2,806 mm

bTotal Length (w/ Drive-up Ramps) 252.25" (21 feet) / 6,409 mm

cOutside length 208.5" (17.4 feet) / 5,294 mm

dHeight of post 170" (14.2 feet) / 4,315 mm

eDrive-thru clearance 87" (7.3 feet) / 2,201 mm

fMaximum rise 151.5" (12.8 feet) / 3,849 mm 79.5" (6.8 feet) / 2,021 mm

gMaximum lifting height 157" (13.1 feet) / 3,986 mm 87" (7.3 feet) / 2,211 mm

hDistance between posts 100" (8.4 feet) / 2,544 mm

iRunway width 19" / 482 mm

jWidth between runways 35" – 41"/ 887 mm – 1,045 mm

kRunway length 199" (16.7 feet) / 5,056 mm 186.75" (15.7 feet) / 4,744 mm

lHeight of Platform when lowered 10.75" / 270 mm 5" / 127 mm

Top Safety Lock 156" (13 feet) / 3,964 mm 84.5" (7 feet) / 2,147 mm

Min. wheelbase @ rated capacity 1140" (11.8 feet) / 3,556 mm 135" (11.3 feet) / 3,429 mm

Min. wheelbase @ 75 capacity 1120" (10 feet) / 3,084 mm 115" (9.7 feet) / 2,921 mm

Min. wheelbase @ 50 capacity 1100" (8.4 feet) / 2,540 mm 95" (7.11 feet) / 2,413 mm

Min. wheelbase @ 25 capacity 180" (6.8 feet) / 2,032 mm 75" (6.3 feet) / 1,905 mm

Safety Locks 34

Spaced every 4" / 102 mm

Lifting time 90 seconds 50 seconds

Motor 220 VAC, 60 Hz, 1 Ph (special voltages available upon request)

1 The Runways supports less weight than its rated capacity if the Vehicle’s wheelbase is shorter

because the wheels of such a Vehicle are closer to the middle of the Runways, where there is less

strength. For example, the maximum weight allowed on the Top Platform for a Vehicle with a

wheelbase of 100" is 50 percent of the Top Platform’s rated capacity (or 3,500 lbs when the rated

capacity is 7,000 lbs).

Specifications subject to change without notice.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bend-Pak Système de levage

Bend-Pak

Bend-Pak GP-9F Manuel utilisateur

Bend-Pak

Bend-Pak HD-973P Manuel utilisateur

Bend-Pak

Bend-Pak LR-10000 Manuel utilisateur

Bend-Pak

Bend-Pak Clearfloor 10AP-168 Manuel utilisateur

Bend-Pak

Bend-Pak XPR-9D Series Manuel utilisateur

Bend-Pak

Bend-Pak PCL-18B Manuel utilisateur

Bend-Pak

Bend-Pak HDS-40X Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10-168 Manuel utilisateur

Bend-Pak

Bend-Pak XPR-9S Manuel utilisateur

Bend-Pak

Bend-Pak HD-12LS Manuel utilisateur

Bend-Pak

Bend-Pak PL-6000DC Manuel de référence

Bend-Pak

Bend-Pak HDS-27 Manuel utilisateur

Bend-Pak

Bend-Pak XPR-12FDL Manuel utilisateur

Bend-Pak

Bend-Pak GP-7LCS Manuel utilisateur

Bend-Pak

Bend-Pak xpR-10C Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10XLS-LP-181 Manuel utilisateur

Bend-Pak

Bend-Pak 5900181 Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10AXLS Manuel utilisateur

Bend-Pak

Bend-Pak PL-6000DC Manuel utilisateur

Bend-Pak

Bend-Pak Turf Maintenance Lift Kit Manuel utilisateur

Bend-Pak

Bend-Pak HD-9AE Manuel utilisateur

Bend-Pak

Bend-Pak P-9000LT Manuel utilisateur

Bend-Pak

Bend-Pak MDS-6EXT Manuel utilisateur

Bend-Pak

Bend-Pak XPR-7TR Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur